The MAX5713/MAX5714/MAX5715 4-channel, low-power,8-/10-/12-bit, voltage-output digital-to-analog converters(DACs) include output buffers and an internal referencethat is selectable to be 2.048V, 2.500V, or 4.096V. TheMAX5713/MAX5714/MAX5715 accept a wide supplyvoltage range of 2.7V to 5.5V with extremely low power(3mW) consumption to accommodate most low-voltageapplications. A precision external reference input allowsrail-to-rail operation and presents a 100kI (typ) load toan external reference.
上傳時間： 2013-12-23
上傳用戶：ArmKing88
The MAX17600–MAX17605 devices are high-speedMOSFET drivers capable of sinking /sourcing 4A peakcurrents. The devices have various inverting and noninvertingpart options that provide greater flexibility incontrolling the MOSFET. The devices have internal logiccircuitry that prevents shoot-through during output-statchanges. The logic inputs are protected against voltagespikes up to +14V, regardless of VDD voltage. Propagationdelay time is minimized and matched between the dualchannels. The devices have very fast switching time,combined with short propagation delays (12ns typ),making them ideal for high-frequency circuits. Thedevices operate from a +4V to +14V single powersupply and typically consume 1mA of supply current.The MAX17600/MAX17601 have standard TTLinput logic levels, while the MAX17603 /MAX17604/MAX17605 have CMOS-like high-noise margin (HNM)input logic levels. The MAX17600/MAX17603 are dualinverting input drivers, the MAX17601/MAX17604 aredual noninverting input drivers, and the MAX17602 /MAX17605 devices have one noninverting and oneinverting input. These devices are provided with enablepins (ENA, ENB) for better control of driver operation.
上傳時間： 2013-12-20
上傳用戶：zhangxin
A MEMS microphone IC is unique among Analog Devices, Inc., products in that its input is an acoustic pressure wave. For this reason, some specifications included in the data sheets for these parts may not be familiar, or familiar specifications may be applied in unfamiliar ways. This application note explains the specifica-tions and terms found in MEMS microphone data sheets so that the microphone can be appropriately designed into a system.
上傳時間： 2013-10-31
上傳用戶：masochism
Abstract: IC switches and multiplexers are proliferating, thanks to near-continual progress in lowering the supply voltage,incorporating fault-protected inputs, clamping the output voltage, and reducing the switch resistances. The latest of these advancesis the inclusion of precision resistors to allow two-point calibration of gain and offset in precision data-acquisition systems.
上傳時間： 2013-11-12
上傳用戶：acwme
The purpose of this application note is to show an example of how a digital potentiometer can be used in thefeedback loop of a step-up DC-DC converter to provide calibration and/or adjustment of the output voltage.The example circuit uses a MAX5025 step-up DC-DC converter (capable of generating up to 36V,120mWmax) in conjunction with a DS1845, 256 position, NV digital potentiometer. For this example, the desiredoutput voltage is 32V, which is generated from an input supply of 5V. The output voltage can be adjusted in35mV increments (near 32V) and span a range wide enough to account for resistance, potentiometer and DCDCconverter tolerances (27.6V to 36.7V).
上傳時間： 2014-12-23
上傳用戶：781354052
The LTC®1966 is a true RMS-to-DC converter that uses aDS computational technique to make it dramatically simplerto use, significantly more accurate, lower in powerconsumption and more flexible than conventional logantilogRMS-to-DC converters. The LTC1966 RMS-to-DCconverter has an input signal range from 5mVRMS to1.5VRMS (a 50dB dynamic range with a single 5V supplyrail) and a 3dB bandwidth of 800kHz with signal crestfactors up to four.
上傳時間： 2013-10-12
上傳用戶：qilin
Abstract: Transimpedance amplifiers (TIAs) are widely used to translate the current output of sensors like photodiode-to-voltagesignals, since several circuits and instruments can only accept voltage input. An operational amplifier with a feedback resistor fromoutput to the inverting input is the most straightforward implementation of such a TIA. However, even this simple TIA circuit requirescareful trade-offs among noise gain, offset voltage, bandwidth, and stability. Clearly stability in a TIA is essential for good, reliableperformance. This application note explains the empirical calculations for assessing stability and then shows how to fine-tune theselection of the feedback phase-compensation capacitor.
標簽： Transimpedance Stabilize Amplifier Your
上傳時間： 2013-11-13
上傳用戶：daoyue
High input impedance and a wide input range are twohighly desirable features in a precision analog-to-digitalconverter, and the LTC®2449 delta-sigma ADC has both.With just a few external components, the LTC2449 formsan exceptional measurement system with very high inputimpedance and an input range that extends 300mV beyondthe supply rails.
上傳時間： 2013-11-02
上傳用戶：ywcftc277
A fully differential amplifi er is often used to converta single-ended signal to a differential signal, a designwhich requires three signifi cant considerations: theimpedance of the single-ended source must match thesingle-ended impedance of the differential amplifi er,the amplifi er’s inputs must remain within the commonmode voltage limits and the input signal must be levelshifted to a signal that is centered at the desired outputcommon mode voltage.
上傳時間： 2013-11-09
上傳用戶：wweqas
The MAX2691 low-noise amplifier (LNA) is designed forGPS L2 applications. Designed in Maxim’s advancedSiGe process, the device achieves high gain andlow noise figure while maximizing the input-referred 1dBcompression point and the 3rd-order intercept point. TheMAX2691 provides a high gain of 17.5dB and sub 1dBnoise figure.
標簽： Amplifier Low-Noise 2691 Band
上傳時間： 2014-12-04
上傳用戶：zaocan888
