The MAX14885E, a 2:2 VGA switch, connects a VGA source to a VGA monitor. To ease direct connection to graphics controllers orthe ASIC, the MAX14885E has two supplies: VCC, a 5V ±5% supply, drives the VGA side interface; and the VL supply sets the logicswitching thresholds on the digital input pins (EN, S00, S01, S10, S11, SHA, SHB, SVA, and SVB). This application note documentsthe proper sequencing of the VCC and VL power supplies on power-up.
標簽： 14885E 14885 MAX VGA
上傳時間： 2013-10-23
上傳用戶：wuchunzhong
Many complex systems—such as telecom equipment,memory modules, optical systems, networking equipment,servers and base stations—use FPGAs and otherdigital ICs that require multiple voltage rails that muststart up and shut down in a specific order, otherwise theICs can be damaged. The LTC®2924 is a simple andcompact solution to power supply sequencing in a 16-pinSSOP package (see Figures 1 and 2).
上傳時間： 2013-10-29
上傳用戶：tonyshao
To this day, Power over Ethernet (PoE) continues to gainpopularity in today’s networking world. The 12.95Wdelivered to the Powered Device (PD) input supplied bythe Power Sourcing Equipment (PSE) is a universal supply.Each PD provides its own DC/DC conversion from anominal 48V supply, thus eliminating the need for a correctvoltage wall adapter. However, higher power devicescan not take advantage of standard PoE because of itspower limitations, and must rely on a large wall adapteras their primary supply. The new LTC4268-1 breaks thispower barrier by allowing for power of up to 35W for suchpower-hungry 2-pair PoE applications. The LTC4268-1provides a complete solution by integrating a high powerPD interface control with an isolated fl yback controller.
上傳時間： 2014-12-24
上傳用戶：jasson5678
Typical industrial and automotive applications requiremultiple high current, low voltage power supply solutionsto drive everything from disc drives to microprocessors.For many of these applications, particularly thosethat have size constraints, the LT3501® dual step-downconverter is an attractive solution because it’s compactand inexpensive compared to a 2-chip solution. The dualconverter accommodates a 3V to 25V input voltage rangeand is capable of supplying up to 3A per channel. Thecircuit in Figure 1 produces 3.3V and 1.8V.
標簽： 排序 雙通道 降壓轉換器
上傳時間： 2014-12-24
上傳用戶：372825274
Piezoelectric motors are used in digital cameras for autofocus,zooming and optical image stabilization. Theyare relatively small, lightweight and effi cient, but theyalso require a complicated driving scheme. Traditionally,this challenge has been met with the use ofseparatecircuits, including a step-up converter and an oversizedgeneric full-bridge drive IC. The resulting high componentcount and large board space are especially problematicin the design of cameras for ever shrinking cell phones.The LT®3572 solves these problems by combining astep-up regulator and a dual full-bridge driver in a 4mm× 4mm QFN package. Figure 1 shows a typical LT3572Piezo motor drive circuit. A step-up converter is usedto generate 30V from a low voltage power source suchas a Li-Ion battery or any input power source within thepart’s wide input voltage range of 2.7V to 10V. The highoutput voltage of the step-up converter, adjustable upto 40V, is available for the drivers at the VOUT pin. Thedrivers operate in a full-bridge fashion, where the OUTAand OUTB pins are the same polarity as the PWMA andPWMB pins, respectively, and the OUTA and OUTB pinsare inverted from PWMA and PWMB, respectively. Thestep-up converter and both Piezo drivers have their ownshutdown control. Figure 2 shows a typical layout
上傳時間： 2013-11-18
上傳用戶：hulee
Avalanche photo diode (APD) receiver modules arewidely used in fi ber optic communication systems. AnAPD module contains the APD and a signal conditioningamplifi er, but is not completely self contained. It stillrequires signifi cant support circuitry including a highvoltage, low noise power supply and a precision currentmonitor to indicate the signal strength. The challenge issqueezing this support circuitry into applications withlimited board space. The LT®3482 addresses this challengeby integrating a monolithic DC/DC step-up converter andan accurate current monitor. The LT3482 can supportup to a 90V APD bias voltage, and the current monitorprovides better than 10% accuracy over four decades ofdynamic range (250nA to 2.5mA).
上傳時間： 2014-01-18
上傳用戶：wenyuoo
The LTC3546 is a dual output current mode buck regulatorwith fl exible output current partitioning. Beyondthe advantages normally associated with dual outputregulators (reduced size, cost, EMI and part count, withimproved effi ciency), the LTC3546’s outputs can bepartitioned for either 3A and 1A outputs, or two 2A outputs.This increases its application range and simplifi esmultiple supply rail designs. A confi gurable Burst Mode®clamp for each output sets the current transition levelbetween Burst Mode operation and forced continuousconduction mode to optimize effi ciency over the entireoutput range. An adjustable switching frequency up to4MHz and internal power MOSFET switches allow forsmall and compact footprints.
上傳時間： 2013-11-04
上傳用戶：yxgi5
The LTC®3610 is a high power monolithic synchronousstep-down DC/DC regulator that can deliver up to 12Aof continuous output current from a 4V to 24V (28Vmaximum) input supply. It is a member of a high currentmonolithic regulator family (see Table 1) that featuresintegrated low RDS(ON) N-channel top and bottomMOSFETs. This results in a high effi ciency and highpower density solution with few external components.This regulator family uses a constant on-time valleycurrent mode architecture that is capable of operatingat very low duty cycles at high frequency and with veryfast transient response. All are available in low profi le(0.9mm max) QFN packages.
上傳時間： 2013-11-07
上傳用戶：moerwang
The LTC®4155 and LTC4156 are dual multiplexed-inputbattery chargers with PowerPath™ control, featuring I2Cprogrammability and USB On-The-Go for systems suchas tablet PCs and other high power density applications.The LTC4155’s float voltage (VFLOAT) range is optimizedfor Li-Ion batteries, while the LTC4156 is optimized forlithium iron phosphate (LiFePO4)batteries, supportingsystem loads to 4A with up to 3.5A of battery chargecurrent. I2C controls a broad range of functions and USBOn-The-Go functionality is controlled directly from theUSB connector ID pin.
標簽： 高電流 便攜式產品 電池充電器 方案
上傳時間： 2013-10-09
上傳用戶：hanhanj
In a recent discussion with a system designer, the requirementfor his power supply was to regulate 1.5Vand deliver up to 40A of current to a load that consistedof four FPGAs. This is up to 60W of power that must bedelivered in a small area with the lowest height profi lepossible to allow a steady fl ow of air for cooling. Thepower supply had to be surface mountable and operateat high enough effi ciency to minimize heat dissipation.He also demanded the simplest possible solution so histime could be dedicated to the more complex tasks. Asidefrom precise electrical performance, this solution had toremovethe heat generated during DC to DC conversionquickly so that the circuit and the ICs in the vicinity do notoverheat. Such a solution requires an innovative designto meet these criteria:
標簽： FPGA DCDC 集成 穩壓器
上傳時間： 2013-11-24
上傳用戶：defghi010
蟲蟲下載站版權所有 京ICP備2021023401號-1
