The purpose of this application note is to show an example of how a digital potentiometer can be used in thefeedback loop of a step-up DC-DC converter to provide calibration and/or adjustment of the output voltage.The example circuit uses a MAX5025 step-up DC-DC converter (capable of generating up to 36V,120mWmax) in conjunction with a DS1845, 256 position, NV digital potentiometer. For this example, the desiredoutput voltage is 32V, which is generated from an input supply of 5V. The output voltage can be adjusted in35mV increments (near 32V) and span a range wide enough to account for resistance, potentiometer and DCDCconverter tolerances (27.6V to 36.7V).
上傳時間： 2014-12-23
上傳用戶：781354052
The LTC®1966 is a true RMS-to-DC converter that uses aDS computational technique to make it dramatically simplerto use, significantly more accurate, lower in powerconsumption and more flexible than conventional logantilogRMS-to-DC converters. The LTC1966 RMS-to-DCconverter has an input signal range from 5mVRMS to1.5VRMS (a 50dB dynamic range with a single 5V supplyrail) and a 3dB bandwidth of 800kHz with signal crestfactors up to four.
上傳時間： 2013-10-12
上傳用戶：qilin
The STM32F10xxx microcontroller family embeds up to three advanced 12-bit ADCs (depending on the device) with a conversion time down to 1 μs. A self-calibration feature is provided to enhance ADC accuracy versus environmental condition changes.
上傳時間： 2014-12-23
上傳用戶：eastimage
One of the most critical components in a step-up design like Figure 1 is the transformer. Transformers have parasitic components that can cause them to deviate from their ideal characteristics, and the parasitic capacitance associated with the secondary can cause large resonating current spikes on the leading edge of the switch current waveform.
上傳時間： 2013-11-22
上傳用戶：15070202241
ANALOG INPUT BANDWIDTH is a measure of the frequencyat which the reconstructed output fundamental drops3 dB below its low frequency value for a full scale input. Thetest is performed with fIN equal to 100 kHz plus integer multiplesof fCLK. The input frequency at which the output is −3dB relative to the low frequency input signal is the full powerbandwidth.APERTURE JITTER is the variation in aperture delay fromsample to sample. Aperture jitter shows up as input noise.APERTURE DELAY See Sampling Delay.BOTTOM OFFSET is the difference between the input voltagethat just causes the output code to transition to the firstcode and the negative reference voltage. Bottom Offset isdefined as EOB = VZT–VRB, where VZT is the first code transitioninput voltage and VRB is the lower reference voltage.Note that this is different from the normal Zero Scale Error.CONVERSION LATENCY See PIPELINE DELAY.CONVERSION TIME is the time required for a completemeasurement by an analog-to-digital converter. Since theConversion Time does not include acquisition time, multiplexerset up time, or other elements of a complete conversioncycle, the conversion time may be less than theThroughput Time.DC COMMON-MODE ERROR is a specification which appliesto ADCs with differential inputs. It is the change in theoutput code that occurs when the analog voltages on the twoinputs are changed by an equal amount. It is usually expressed in LSBs.
上傳時間： 2013-11-12
上傳用戶：pans0ul
Power conversion by virtue of its basic role produces harmonics due to theslicing of either voltages or currents. To a large extent the pollution in theutility supply and the deterioration of the power quality has been generatedor created by non-linear converters. It is therefore ironic that power convertersshould now be used to clean up the pollution that they helped to create inthe first place.In a utility system, it is desirable to prevent harmonic currents (which resultin EMI and resonance problems) and limit reactive power flows (whichresult in transmission losses).Traditionally, shunt passive filters, comprised of tuned LC elements andcapacitor banks, were used to filter the harmonics and to compensate forreactive current due to non-linear loads. However, in practical applicationsthese methods have many disadvantages.
上傳時間： 2013-11-05
上傳用戶：AISINI005
Finite state machines are widely used in digital circuit designs. Generally, when designing a state machine using an HDL, the synthesis tools will optimize away all states that cannot be reached and generate a highly optimized circuit. Sometimes, however, the optimization is not acceptable. For example, if the circuit powers up in an invalid state, or the circuit is in an extreme working environment and a glitch sends it into an undesired state, the circuit may never get back to its normal operating condition.
標簽： Creating Machines Mentor State
上傳時間： 2013-10-08
上傳用戶：wangzhen1990
good good study ，day day up
上傳時間： 2014-05-15
上傳用戶：wvbxj
討論、研究高性能覆銅板對它所用的環氧樹脂的性能要求，應是立足整個產業鏈的角度去觀察、分析。特別應從HDI多層板發展對高性能CCL有哪些主要性能需求上著手研究。HDI多層板有哪些發展特點，它的發展趨勢如何——這都是我們所要研究的高性能CCL發展趨勢和重點的基本依據。而HDI多層板的技術發展，又是由它的應用市場——終端電子產品的發展所驅動（見圖1）。 圖1 在HDI多層板產業鏈中各類產品對下游產品的性能需求關系圖 1．HDI多層板發展特點對高性能覆銅板技術進步的影響1.1 HDI多層板的問世，對傳統PCB技術及其基板材料技術是一個嚴峻挑戰20世紀90年代初，出現新一代高密度互連（High Density Interconnection，簡稱為 HDI）印制電路板——積層法多層板（Build—Up Multiplayer printed board，簡稱為 BUM）的最早開發成果。它的問世是全世界幾十年的印制電路板技術發展歷程中的重大事件。積層法多層板即HDI多層板，至今仍是發展HDI的PCB的最好、最普遍的產品形式。在HDI多層板之上，將最新PCB尖端技術體現得淋漓盡致。HDI多層板產品結構具有三大突出的特征：“微孔、細線、薄層化”。其中“微孔”是它的結構特點中核心與靈魂。因此，現又將這類HDI多層板稱作為“微孔板”。HDI多層板已經歷了十幾年的發展歷程，但它在技術上仍充滿著朝氣蓬勃的活力，在市場上仍有著前程廣闊的空間。
上傳時間： 2013-11-22
上傳用戶：gundan
This document provides practical, common guidelines for incorporating PCI Express interconnect layouts onto Printed Circuit Boards (PCB) ranging from 4-layer desktop baseboard designs to 10- layer or more server baseboard designs. Guidelines and constraints in this document are intended for use on both baseboard and add-in card PCB designs. This includes interconnects between PCI Express devices located on the same baseboard (chip-to-chip routing) and interconnects between a PCI Express device located “down” on the baseboard and a device located “up” on an add-in card attached through a connector. This document is intended to cover all major components of the physical interconnect including design guidelines for the PCB traces, vias and AC coupling capacitors, as well as add-in card edge-finger and connector considerations. The intent of the guidelines and examples is to help ensure that good high-speed signal design practices are used and that the timing/jitter and loss/attenuation budgets can also be met from end-to-end across the PCI Express interconnect. However, while general physical guidelines and suggestions are given, they may not necessarily guarantee adequate performance of the interconnect for all layouts and implementations. Therefore, designers should consider modeling and simulation of the interconnect in order to ensure compliance to all applicable specifications. The document is composed of two main sections. The first section provides an overview of general topology and interconnect guidelines. The second section concentrates on physical layout constraints where bulleted items at the beginning of a topic highlight important constraints, while the narrative that follows offers additional insight.
上傳時間： 2013-10-15
上傳用戶：busterman
