關于GL827L的資料
標簽： Report_SSOP Test 827 102
上傳時間： 2014-01-08
上傳用戶：lz4v4
This application note provides step-by-step instructions on how to recreate a Tri-Mode Ethernet(TEMAC) performance testing system using the ML405 board and MontaVista Linux 4.0. Thisapplication note shows how to set up a simple EDK Base System Builder system on the ML405Evaluation Platform and run performance tests. The network architecture for the test isdescribed. A system is built and downloaded into the FPGA. A MontaVista Linux kernel isconfigured, built, and downloaded into the ML405 Evaluation Platform. The instructions forobtaining and setting up the software used to perform the measurements, netperf, are given.
上傳時間： 2013-11-11
上傳用戶：saharawalker
The correct answer for each test bank question is highlighted in bold. Test bank questions are based on the end-of-chapter questions. If a student studies the end-of-chapter questions (which are linked to the italicized words in each chapter), then they will be successful on the test bank questions.
上傳時間： 2014-12-31
上傳用戶：旗魚旗魚
AI :Auto-Insertion 自動插件 AQL :acceptable quality level 允收水準 ATE :automatic test equipment 自動測試 ATM :atmosphere 氣壓 BGA :ball grid array 球形矩陣
上傳時間： 2013-11-20
上傳用戶：haoxiyizhong
隨著科學技術的不斷發展，人們的生活水平的不斷提高，通信技術的不斷擴延，計算機已經涉及到各個不同的行業，成為人們生活、工作、學習、娛樂不可缺少的工具。而計算機主板作為計算機中非常重要的核心部件，其品質的好壞直接影響計算機整體品質的高低。因此在生產主板的過程中每一步都是要嚴格把關的，不能有絲毫的懈怠，這樣才能使其品質得到保證。 基于此，本文主要介紹電腦主板的SMT生產工藝流程和F/T(Function Test)功能測試步驟（F/T測試步驟以惠普H310機種為例）。讓大家了解一下完整的計算機主板是如何制成的，都要經過哪些工序以及如何檢測產品質量的。 本文首先簡單介紹了PCB板的發展歷史，分類，功能及發展趨勢，SMT及SMT產品制造系統，然后重點介紹了SMT生產工藝流程和F/T測試步驟。
上傳時間： 2013-11-02
上傳用戶：c12228
This application note covers the design considerations of a system using the performance features of the LogiCORE™ IP Advanced eXtensible Interface (AXI) Interconnect core. The design focuses on high system throughput through the AXI Interconnect core with F MAX and area optimizations in certain portions of the design. The design uses five AXI video direct memory access (VDMA) engines to simultaneously move 10 streams (five transmit video streams and five receive video streams), each in 1920 x 1080p format, 60 Hz refresh rate, and up to 32 data bits per pixel. Each VDMA is driven from a video test pattern generator (TPG) with a video timing controller (VTC) block to set up the necessary video timing signals. Data read by each AXI VDMA is sent to a common on-screen display (OSD) core capable of multiplexing or overlaying multiple video streams to a single output video stream. The output of the OSD core drives the DVI video display interface on the board. Performance monitor blocks are added to capture performance data. All 10 video streams moved by the AXI VDMA blocks are buffered through a shared DDR3 SDRAM memory and are controlled by a MicroBlaze™ processor. The reference system is targeted for the Virtex-6 XC6VLX240TFF1156-1 FPGA on the Xilinx® ML605 Rev D evaluation board
上傳時間： 2013-11-23
上傳用戶：shen_dafa
針對傳統集成電路（ASIC）功能固定、升級困難等缺點，利用FPGA實現了擴頻通信芯片STEL-2000A的核心功能。使用ISE提供的DDS IP核實現NCO模塊，在下變頻模塊調用了硬核乘法器并引入CIC濾波器進行低通濾波，給出了DQPSK解調的原理和實現方法，推導出一種簡便的引入?仔/4固定相移的實現方法。采用模塊化的設計方法使用VHDL語言編寫出源程序，在Virtex-II Pro 開發板上成功實現了整個系統。測試結果表明該系統正確實現了STEL-2000A的核心功能。 Abstract: To overcome drawbacks of ASIC such as fixed functionality and upgrade difficulty, FPGA was used to realize the core functions of STEL-2000A. This paper used the DDS IP core provided by ISE to realize the NCO module, called hard core multiplier and implemented CIC filter in the down converter, described the principle and implementation detail of the demodulation of DQPSK, and derived a simple method to introduce a fixed phase shift of ?仔/4. The VHDL source code was designed by modularity method , and the complete system was successfully implemented on Virtex-II Pro development board. Test results indicate that this system successfully realize the core function of the STEL-2000A.
上傳時間： 2013-11-19
上傳用戶：neu_liyan
為了在CDMA系統中更好地應用QDPSK數字調制方式，在分析四相相對移相（QDPSK)信號調制解調原理的基礎上，設計了一種QDPSK調制解調電路，它包括串并轉換、差分編碼、四相載波產生和選相、相干解調、差分譯碼和并串轉換電路。在MAX+PLUSⅡ軟件平臺上，進行了編譯和波形仿真。綜合后下載到復雜可編程邏輯器件EPM7128SLC84-15中，測試結果表明，調制電路能正確選相，解調電路輸出數據與QDPSK調制輸入數據完全一致，達到了預期的設計要求。 Abstract: In order to realize the better application of digital modulation mode QDPSK in the CDMA system， a sort of QDPSK modulation-demodulation circuit was designed based on the analysis of QDPSK signal modulation-demodulation principles. It included serial/parallel conversion circuit, differential encoding circuit, four-phase carrier wave produced and phase chosen circuit, coherent demodulation circuit, difference decoding circuit and parallel/serial conversion circuit. And it was compiled and simulated on the MAX+PLUSⅡ software platform,and downloaded into the CPLD of EPM7128SLC84-15.The test result shows that the modulation circuit can exactly choose the phase，and the output data of the demodulator circuit is the same as the input data of the QDPSK modulate. The circuit achieves the prospective requirement of the design.
上傳時間： 2013-10-28
上傳用戶：jyycc
UART 4 UART參考設計，Xilinx提供VHDL代碼 uart_vhdl This zip file contains the following folders: \vhdl_source -- Source VHDL files: uart.vhd - top level file txmit.vhd - transmit portion of uart rcvr.vhd - - receive portion of uart \vhdl_testfixture -- VHDL Testbench files. This files only include the testbench behavior, they do not instantiate the DUT. This can easily be done in a top-level VHDL file or a schematic. This folder contains the following files: txmit_tb.vhd -- Test bench for txmit.vhd. rcvr_tf.vhd -- Test bench for rcvr.vhd.
上傳時間： 2013-11-02
上傳用戶：18862121743
PCB LAYOUT 術語解釋(TERMS)1. COMPONENT SIDE(零件面、正面)︰大多數零件放置之面。2. SOLDER SIDE(焊錫面、反面)。3. SOLDER MASK(止焊膜面)︰通常指Solder Mask Open 之意。4. TOP PAD︰在零件面上所設計之零件腳PAD，不管是否鑽孔、電鍍。5. BOTTOM PAD：在銲錫面上所設計之零件腳PAD，不管是否鑽孔、電鍍。6. POSITIVE LAYER：單、雙層板之各層線路；多層板之上、下兩層線路及內層走線皆屬之。7. NEGATIVE LAYER：通常指多層板之電源層。8. INNER PAD：多層板之POSITIVE LAYER 內層PAD。9. ANTI-PAD：多層板之NEGATIVE LAYER 上所使用之絕緣範圍，不與零件腳相接。10. THERMAL PAD：多層板內NEGATIVE LAYER 上必須零件腳時所使用之PAD，一般稱為散熱孔或導通孔。11. PAD (銲墊)：除了SMD PAD 外，其他PAD 之TOP PAD、BOTTOM PAD 及INNER PAD 之形狀大小皆應相同。12. Moat : 不同信號的 Power& GND plane 之間的分隔線13. Grid : 佈線時的走線格點2. Test Point : ATE 測試點供工廠ICT 測試治具使用ICT 測試點 LAYOUT 注意事項:PCB 的每條TRACE 都要有一個作為測試用之TEST PAD(測試點)，其原則如下：1. 一般測試點大小均為30-35mil，元件分布較密時，測試點最小可至30mil.測試點與元件PAD 的距離最小為40mil。2. 測試點與測試點間的間距最小為50-75mil，一般使用75mil。密度高時可使用50mil,3. 測試點必須均勻分佈於PCB 上，避免測試時造成板面受力不均。4. 多層板必須透過貫穿孔(VIA)將測試點留於錫爐著錫面上(Solder Side)。5. 測試點必需放至於Bottom Layer6. 輸出test point report(.asc 檔案powerpcb v3.5)供廠商分析可測率7. 測試點設置處:Setuppadsstacks
上傳時間： 2013-11-17
上傳用戶：cjf0304
<abbr id="quowq"></abbr>