Hid Led Tester is a simple USB(interrupt mode)device tester package. There are firmware and software in it. Hid Led tester follows USB HID protocol, we don’t need to install driver for the device, and Windows (Win 2000 and later) will install the device automatic.
ECE345, Visual-to-Audio Electronic Travel Aid
Code for TM320C54x (v2a.asm) download
This project involves the design and implementation of a audio synthesis device that converts moving images into audio signals. The system is built on a TM320C54x DSP with interface to an IMAQ camera module via the serial port on a PC. Brief description: A LabVIEW VI acquires an image from the IMAQ camera module. It quantizes the image into a 5x5, 3-bit image, and sends the data to the TM320C54x DSP via a serial port. The TM320C54x DSP constructs a 64-tap FIR by combining a series of 64-tap head related transfer functions (HRTF) according to the incoming data, and then filters an input audio signal with this FIR filter, in effect creating a correspondence between the filtered signal and the original image.
Bootloading the TMS320VC5506/C5507/C5509 A digital signal processor (DSP)
through the on-chip universal serial bus (USB) peripheral is part of the standard
bootloader provided on the device. This document describes the procedures for
physically connecting the DSP to a USB host, invoking the USB bootloader on the
DSP, generating the correct boot table file, and downloading the boot table from the
host to the DSP via USB.
The USB Multi-Interface driver is a replacement driver for the system provided Multi-Interface driver. This driver was developed to overcome some bugs that are included in the build in driver and to introduce new features. The driver is compatible to the system provided Multi-Interface driver. If the driver is installed on a system, it does not automatically replace the system provided driver. It exists parallel to the system driver and is assigned to a device during the installation process.
The TMS320VC5506/C5507/C5509A USB peripherals can be clocked from either the USB APLL or the
USB DPLL. Since the APLL is inherently more noise tolerant and has less long-term jitter than the DPLL,
it is recommended that you switch to it for any USB operations.
This software package contains the USB framework core developped by ATMEL,
as well as a Mass storage driver. The MSD driver uses the internal flash
of the chip to operate as a disk-on-key.
The following files are included :
- core/
-> Source code for the framework core
-> Makefile for the core
- msd/
-> Source code for the Mass Storage driver
-> Makefile for the MSD driver
- bin/
-> Compiled binaries for every supported chips
- lib/
-> Lib v3 files for every supported chips
- ./
-> Makefile for the framework
-> Startup file
Serial UART open source core. The design is engineered for use as a stand alone chip or for use with other of our cores. The reason for developing the Serial UART core is the fact, that asynchronous serial communication is very common that almost every machine understands it.Also, for OCRP-1, we needed a way of communication with a host computer, to make it available over the net.
Builder uses to integrate a larger system module. Each component
consists of a structured set of files within a directory.
The files in a component directory serve the following
The RS232 UART Core implements a method for communication of serial data. The core provides
a simple register-mapped Avalon廬 interface. Master peripherals [such as a Nios廬 II processor]
communicate with the core by reading and writing control and data registers.
The AT24C512 provides 524,288 bits of serial electrically erasable and programmable
read only memory (EEPROM) organized as 65,536 words of 8 bits each. The device鈥檚
cascadable feature allows up to four devices to share a common two-wire bus. The
device is optimized for use in many industrial and commercial applications where lowpower
and low-voltage operation are essential. The devices are available in spacesaving
8-pin PDIP, 8-lead EIAJ SOIC, 8-lead JEDEC SOIC, 8-lead TSSOP, 8-lead
Leadless Array (LAP), and 8-lead SAP packages. In addition, the entire family is available
in 2.7V (2.7V to 5.5V) and 1.8V (1.8V to 3.6V) versions.
R1EX24xxx series are two-wire serial interface EEPROM (Electrically Erasable and Programmable
ROM). They realize high speed, low power consumption and a high level of reliability by employing
advanced MNOS memory technology and CMOS process and low voltage circuitry technology. They
also have a 128-byte page programming function to make their write operation faster.
Note: Renesas Technology鈥檚 serial EEPROM are authorized for using consumer applications such as
cellular phone, camcorders, audio equipment. Therefore, please contact Renesas Technology鈥檚
sales office before using industrial applications such as automotive systems, embedded controllers,
and meters