基于單DSP的VoIP模擬電話適配器研究與實現:提出和實現了一種新穎的基于單個通用數字信號處理器(DSP)的VoIP模擬電話適配器方案。DSP的I/O和存儲資源非常有限，通常適于運算密集型應用，不適宜控制密集型應用[5]。該系統高效利用單DSP的I/O和片內外存儲器資源，采用μC/OS-II嵌入式實時操作系統，支持SIP和TCP-UDP/IP協議，通過LAN或者寬帶接入，使普通電話機成為Internet終端，實現IP電話。該系統軟硬件結構緊湊高效，運行穩定，成本低，具有廣闊的應用前景。關鍵詞：模擬電話適配器；IP電話；數字信號處理器；μC/OS-II 【Abstract】This paper presents a VoIP ATA solution based on a single digital signal processor (DSP). DSPs are suitable for arithmetic-intensiveapplication and unsuitable for control-intensive application because of the limitation of I/O and memory resources. This solution is based on a 16-bitfixed-point DSP and μC/OS-II embedded real-time operating system. It makes good use of the limited resources, supports SIP and TCP-UDP/IPprotocol. It can connect the analog telephone to Internet and realize the VoIP application. This system has a great future for its high efficiency andlow cost.【Key words】Analog telephone adapter (ATA); Voice over Internet protocol (VoIP); Digital signal processor (DSP); μC/OS-II Research and Implementation of VoIPATA Based on Single DSP
上傳時間： 2013-11-20
上傳用戶：Wwill
Microchip ZigBee協議棧:ZigBee™ 是專為低速率傳感器和控制網絡設計的無線網絡協議。有許多應用可從ZigBee 協議受益，其中可能的一些應用有：建筑自動化網絡、住宅安防系統、工業控制網絡、遠程抄表以及PC 外設。與其他無線協議相比， ZigBee 無線協議提供了低復雜性、縮減的資源要求，最重要的是它提供了一組標準的規范。它還提供了三個工作頻帶，以及一些網絡配置和可選的安全功能。如果您正在尋求現有的控制網絡技術（例如RS-422、RS-485）或專有無線協議的替代方案， ZigBee 協議可能是您所需的解決方案。此應用筆記旨在幫助您在應用中采用ZigBee 協議。 可以使用在應用筆記中提供的Microchip ZigBee 協議棧快速地構建應用。為了說明該協議棧的用法，本文包含了兩個有效的演示應用程序。可將這兩個演示程序作為參考或者根據您的需求經過簡單修改來采用它們。此應用筆記中提供的協議棧函數庫實現了一個與物理層無關的應用程序接口。 因此，無需做重大修改就可以輕松地在射頻（Radio Frequency，RF）收發器之間移植應用程序。在此文檔末尾的“常見問題解答”中提供了有關Microchip 協議棧和用法的一些常見問題及其答案。
上傳時間： 2013-10-08
上傳用戶：u789u789u789
The μPSD32xx family, from ST, consists of Flash programmable system devices with a 8032 MicrocontrollerCore. Of these, the μPSD3234A and μPSD3254A are notable for having a complete implementationof the USB hardware directly on the chip, complying with the Universal Serial Bus Specification, Revision1.1.This application note describes a demonstration program that has been written for the DK3200 hardwaredemonstration kit (incorporating a μPSD3234A device). It gives the user an idea of how simple it is to workwith the device, using the HID class as a ready-made device driver for the USB connection.IN-APPLICATION-PROGRAMMING (IAP) AND IN-SYSTEM-PROGRAMMING (ISP)Since the μPSD contains two independent Flash memory arrays, the Micro Controller Unit (MCU) can executecode from one memory while erasing and programming the other. Product firmware updates in thefield can be reliably performed over any communication channel (such as CAN, Ethernet, UART, J1850)using this unique architecture. For In-Application-Programming (IAP), all code is updated through theMCU. The main advantage for the user is that the firmware can be updated remotely. The target applicationruns and takes care on its own program code and data memory.IAP is not the only method to program the firmware in μPSD devices. They can also be programmed usingIn-System-Programming (ISP). A IEEE1149.1-compliant JTAG interface is included on the μPSD. Withthis, the entire device can be rapidly programmed while soldered to the circuit board (Main Flash memory,Secondary Boot Flash memory, the PLD, and all configuration areas). This requires no MCU participation.The MCU is completely bypassed. So, the μPSD can be programmed or reprogrammed any time, anywhere, even when completely uncommitted.Both methods take place with the device in its normal hardware environment, soldered to a printed circuitboard. The IAP method cannot be used without previous use of ISP, because IAP utilizes a small amountof resident code to receive the service commands, and to perform the desired operations.
標簽： Demonstration 3200 USB for
上傳時間： 2014-02-27
上傳用戶：zhangzhenyu
This application note shows how to write an Inter Integrated Circuit bus driver (I²C) for the Philips P90CL301micro-controller.It is not only an example of writing a driver, but it also includes a set of application interface software routines toquickly implement a complete I²C multi-master system application.For specific applications the user will have to make minimal changes in the driver program. Using the drivermeans linking modules to your application software and including a header-file into the application sourceprograms. A small example program of how to use the driver is listed.The driver supports i.a. polled or interrupt driven message handling, slave message transfers and multi-mastersystem applications. Furthermore, it is made suitable for use in conjunction with real time operating systems, likepSOS+.
上傳時間： 2013-11-23
上傳用戶：weixiao99
All inputs of the C16x family have Schmitt-Trigger input characteristics. These Schmitt-Triggers are intended to always provide proper internal low and high levels, even if anundefined voltage level (between TTL-VIL and TTL-VIH) is externally applied to the pin.The hysteresis of these inputs, however, is very small, and can not be properly used in anapplication to suppress signal noise, and to shape slow rising/falling input transitions.Thus, it must be taken care that rising/falling input signals pass the undefined area of theTTL-specification between VIL and VIH with a sufficient rise/fall time, as generally usualand specified for TTL components (e.g. 74LS series: gates 1V/us, clock inputs 20V/us).The effect of the implemented Schmitt-Trigger is that even if the input signal remains inthe undefined area, well defined low/high levels are generated internally. Note that allinput signals are evaluated at specific sample points (depending on the input and theperipheral function connected to it), at that signal transitions are detected if twoconsecutive samples show different levels. Thus, only the current level of an input signalat these sample points is relevant, that means, the necessary rise/fall times of the inputsignal is only dependant on the sample rate, that is the distance in time between twoconsecutive evaluation time points. If an input signal, for instance, is sampled throughsoftware every 10us, it is irrelevant, which input level would be seen between thesamples. Thus, it would be allowable for the signal to take 10us to pass through theundefined area. Due to the sample rate of 10us, it is assured that only one sample canoccur while the signal is within the undefined area, and no incorrect transition will bedetected. For inputs which are connected to a peripheral function, e.g. capture inputs, thesample rate is determined by the clock cycle of the peripheral unit. In the case of theCAPCOM unit this means a sample rate of 400ns @ 20MHz CPU clock. This requiresinput signals to pass through the undefined area within these 400ns in order to avoidmultiple capture events.For input signals, which do not provide the required rise/fall times, external circuitry mustbe used to shape the signal transitions.In the attached diagram, the effect of the sample rate is shown. The numbers 1 to 5 in thediagram represent possible sample points. Waveform a) shows the result if the inputsignal transition time through the undefined TTL-level area is less than the time distancebetween the sample points (sampling at 1, 2, 3, and 4). Waveform b) can be the result ifthe sampling is performed more than once within the undefined area (sampling at 1, 2, 5,3, and 4).Sample points:1. Evaluation of the signal clearly results in a low level2. Either a low or a high level can be sampled here. If low is sampled, no transition willbe detected. If the sample results in a high level, a transition is detected, and anappropriate action (e.g. capture) might take place.3. Evaluation here clearly results in a high level. If the previous sample 2) had alreadydetected a high, there is no change. If the previous sample 2) showed a low, atransition from low to high is detected now.
上傳時間： 2013-10-23
上傳用戶：copu
All inputs of the C16x family have Schmitt-Trigger input characteristics. These Schmitt-Triggers are intended to always provide proper internal low and high levels, even if anundefined voltage level (between TTL-VIL and TTL-VIH) is externally applied to the pin.The hysteresis of these inputs, however, is very small, and can not be properly used in anapplication to suppress signal noise, and to shape slow rising/falling input transitions.Thus, it must be taken care that rising/falling input signals pass the undefined area of theTTL-specification between VIL and VIH with a sufficient rise/fall time, as generally usualand specified for TTL components (e.g. 74LS series: gates 1V/us, clock inputs 20V/us).The effect of the implemented Schmitt-Trigger is that even if the input signal remains inthe undefined area, well defined low/high levels are generated internally. Note that allinput signals are evaluated at specific sample points (depending on the input and theperipheral function connected to it), at that signal transitions are detected if twoconsecutive samples show different levels. Thus, only the current level of an input signalat these sample points is relevant, that means, the necessary rise/fall times of the inputsignal is only dependant on the sample rate, that is the distance in time between twoconsecutive evaluation time points. If an input signal, for instance, is sampled throughsoftware every 10us, it is irrelevant, which input level would be seen between thesamples. Thus, it would be allowable for the signal to take 10us to pass through theundefined area. Due to the sample rate of 10us, it is assured that only one sample canoccur while the signal is within the undefined area, and no incorrect transition will bedetected. For inputs which are connected to a peripheral function, e.g. capture inputs, thesample rate is determined by the clock cycle of the peripheral unit. In the case of theCAPCOM unit this means a sample rate of 400ns @ 20MHz CPU clock. This requiresinput signals to pass through the undefined area within these 400ns in order to avoidmultiple capture events.
上傳時間： 2014-04-02
上傳用戶：han_zh
This application note demonstrates how to write an Inter Integrated Circuit bus driver (I2C) for the XA-S3 16-bitMicrocontroller from Philips Semiconductors.Not only the driver software is given. This note also contains a set of (example) interface routines and a smalldemo application program. All together it offers the user a quick start in writing a complete I2C system applicationwith the PXAS3x.The driver routines support interrupt driven single master transfers. Furthermore, the routines are suitable foruse in conjunction with real time operating systems.
上傳時間： 2013-11-02
上傳用戶：zw380105939
I2C interface, is a very powerful tool for system designers. Theintegrated protocols allow systems to be completely software defined.Software development time of different products can be reduced byassembling a library of reusable software modules. In addition, themultimaster capability allows rapid testing and alignment ofend-products via external connections to an assembly-line computer.The mask programmable 87LPC76X and its EPROM version, the87LPC76X, can operate as a master or a slave device on the I2Csmall area network. In addition to the efficient interface to thededicated function ICs in the I2C family, the on-board interfacefacilities I/O and RAM expansion, access to EEPROM andprocessor-to-processor communications.
標簽： microcontro Using 76X LPC
上傳時間： 2013-12-30
上傳用戶：Artemis
//芯片資料請到www.elecfans.com查找 //DS1820 C51 子程序//這里以11.0592M晶體為例，不同的晶體速度可能需要調整延時的時間//sbit DQ =P2^1;//根據實際情況定義端口 typedef unsigned char byte;typedef unsigned int word; //延時void delay(word useconds){ for(;useconds>0;useconds--);} //復位byte ow_reset(void){ byte presence; DQ = 0; //pull DQ line low delay(29); // leave it low for 480us DQ = 1; // allow line to return high delay(3); // wait for presence presence = DQ; // get presence signal delay(25); // wait for end of timeslot return(presence); // presence signal returned} // 0=presence, 1 = no part //從 1-wire 總線上讀取一個字節byte read_byte(void){ byte i; byte value = 0; for (i=8;i>0;i--) { value>>=1; DQ = 0; // pull DQ low to start timeslot DQ = 1; // then return high delay(1); //for (i=0; i<3; i++); if(DQ)value|=0x80; delay(6); // wait for rest of timeslot } return(value);} //向 1-WIRE 總線上寫一個字節void write_byte(char val){ byte i; for (i=8; i>0; i--) // writes byte, one bit at a time { DQ = 0; // pull DQ low to start timeslot DQ = val&0x01; delay(5); // hold value for remainder of timeslot DQ = 1; val=val/2; } delay(5);} //讀取溫度char Read_Temperature(void){ union{ byte c[2]; int x; }temp; ow_reset(); write_byte(0xCC); // Skip ROM write_byte(0xBE); // Read Scratch Pad temp.c[1]=read_byte(); temp.c[0]=read_byte(); ow_reset(); write_byte(0xCC); //Skip ROM write_byte(0x44); // Start Conversion return temp.x/2;}
上傳時間： 2013-11-03
上傳用戶：hongmo
#include <reg51.h>#include<intrins.h> #define BUSY1 (DQ1==0) sbit DQ1 = P0^4; unsigned char idata TMP; unsigned char idata TMP_d; unsigned char f; void wr_ds18_1(char dat);unsigned char rd_ds18_1(); /***************延時程序，單位us,大于10us*************/void time_delay(unsigned char time){ time=time-10; time=time/6; while(time!=0)time--;} /*****************************************************//* reset ds18b20 *//*****************************************************/void ds_reset_1(void){ unsigned char idata count=0; DQ1=0; time_delay(240); time_delay(240); DQ1=1; return;}
上傳時間： 2013-10-29
上傳用戶：sssnaxie
