Wherever possible the overall technique used for this series will be "definition by example" withgeneric formulae included for use in other applications. To make stability analysis easy we will usemore than one tool from our toolbox with data sheet information, tricks, rules-of-thumb, SPICESimulation, and real-world testing all accelerating our design of stable operational amplifier (op amp)circuits. These tools are specifically targeted at voltage feedback op amps with unity-gain bandwidths<20 MHz, although many of the techniques are applicable to any voltage feedback op amp. 20 MHz ischosen because as we increase to higher bandwidth circuits there are other major factors in closing theloop: such as parasitic capacitances on PCBs, parasitic inductances in capacitors, parasitic inductancesand capacitances in resistors, etc. Most of the rules-of-thumb and techniques were developed not justfrom theory but from the actual building of real-world circuits with op amps <20 MHz.
CHAPTER 1: THE OP AMP CHAPTER 2: OTHER LINEAR CIRCUITS CHAPTER 3: SENSORS CHAPTER 4: RF/IF CIRCUITS CHAPTER 5: FUNDAMENTALS OF SAMPLED DATA SYSTEMS CHAPTER 6: CONVERTERS CHAPTER 7: DATA CONVERTER SUPPORT CIRCUITS CHAPTER 8: ANALOG FILTERS CHAPTER 9: POWER MANAGEMENT CHAPTER 10: PASSIVE COMPONENTS CHAPTER 11: OVERVOLTAGE EFFECTS ON ANALOG INTEGRATED CIRCUITS CHAPTER 12: PRINTED CIRCUIT BOARD (PCB) DESIGN ISSUES CHAPTER 13: DESIGN DEVELOPMENT TOOLS
The PW2606B is a front-end over voltage and over current protection device. It achieves wide inputvoltage range from 2.5VDC to 40VDC. The over voltage threshold can be programmed externally orset to internal default setting. The low resistance of integrated power path nFET switch ensures betterperformance for battery charging system applications. It can deliver up to 1A current to satisfy thebattery supply system. It integrates the over-temperature protection shutdown and auto-recoverycircuit with hysteresis to protect against over current events
The PW2601 is a charger front-end integrated circuit designed to provide protection to Li-ionbatteries from failures of charging circuitry. The device monitors the input voltage, battery voltageand the charging current to make sure all three parameters are operated in normal range. Thedevice will switch off internal MOSFET to disconnect IN to OUT to protect load when any of inputvoltage, output current exceeds the threshold. The Over temperature protection (OTP) functionmonitors chip temperature to protect the device. The PW2601 also can protect the system’sbattery from being over charged by monitors the battery voltage continuously. The deviceoperates like a linear regulator, maintaining a 5.1V output with input voltages up to the input overvoltage threshold.The PW2601 is available in DFN-2x2-8L package. Standard products are Pb-free and Halogenfree
ADC模數轉換器件Altium Designer AD原理圖庫元件庫SV text has been written to file : 4.4 - ADC模數轉換器件.csvLibrary Component Count : 29Name Description----------------------------------------------------------------------------------------------------ADC0800 National 8-Bit Analog to Digital ConverterADC0809 ADC0831 ADCADC0832 ADC8 Generic 8-Bit A/D ConverterCLC532 High-Speed 2:1 Analog MultiplexerCS5511 National 16-Bit Analog to Digital ConverterDAC8 Generic 8-Bit D/A ConverterEL1501 Differential line Driver/ReceiverEL2082 Current-Mode MultiplierEL4083 Current Mode Four Quadrant MultiplierEL4089 DC Restored Video AmplifierEL4094 Video Gain Control/FaderEL4095 Video Gain Contol/Fader/MultiplexerICL7106 LMC6953_NSC PCI Local Bus Power SupervisorMAX4147 300MHz, Low-Power, High-Output-Current, Differential Line DriverMAX4158 350MHz 2-Channel Video Multiplexer-AmplifierMAX4159 350MHz 2-Channel Video Multiplexer-AmplifierMAX4258 250MHz, 2-Channel Video Multiplexer-AmplifierMAX4259 250MHz 2-Channel Video Multiplexer-AmplifierMAX951 Ultra-Low-Power, Single-Supply Op Amp + Comparator + ReferenceMAX952 Ultra-Low-Power, Single-Supply Op Amp + Comparator + ReferenceMC1496 Balanced Modulator/DemodulatorPLL100k Generic Phase Locked LoopPLL10k Generic Phase Locked LoopPLL5k Generic Phase Locked LoopPLLx Generic Phase Locked Loop水位計
為了提高超高頻RFID系統中閱讀器在低信噪比的情況下仍具有較高的識別能力,提出一種基于FPGA系統結合軟件無線電方法實現超高頻RFID射頻前端電路方案。超高頻射頻識別系統必須符合EPC Class 1generation 2標準,所設計的電路系統以Xilinx公司的XC6SLX16-2CSG324FPGA芯片為硬件基礎,將數字基帶調制解調和中頻濾波電路在FPGA系統中設計實現,重點闡述了射頻前端電路的設計結構、AD/DA轉換電路,以及數字濾波器的設計。實驗結果表明,所設計的超高頻RFID閱讀器簡化了前端電路系統結構,提升了穩定性,增強了抗干擾能力。該電路系統在信噪比較低的情況下,能夠較好地實現915MHz頻率的射頻接收和發送。In order to improve the reader UHF RFID system still has a higher ability to identify,in the case of low signal-to-noise ratio.The UHF RFID systems must comply with EPC Class 1 generation 2 standard.In this paper,the design of the circuit system based on Xilinx＇s XC6SLX16-2CSG324 FPGA chip,and presents UHF RFID RF front-end circuit with software radio based on FPGA system.Digital baseband modem and IF filter circuit is designed and implemented in the FPGA system,and focused on designing the structure of the RF front-end circuit,AD/DA conversion circuits,and digital filter.Experimental results show that the UHF RFID reader de...
