<sup id="mkoim"></sup>
Op Amp Applications Handbook
上傳時間： 2013-06-08
上傳用戶：哇哇哇哇哇
單電源運放使用指南《A Single-Supply Op-Amp Circuit Collection》
上傳時間： 2013-06-22
上傳用戶：17854267178
運放使用經驗談 為您的電路選擇合適的運算放大器 (op amp) 時，首先要做的便是確定系統通過該放大器進行傳輸的信號帶寬。一旦您確定下來這一點，您便可以開始尋找正確的放大器。
上傳時間： 2013-05-16
上傳用戶：561596
Abstract: This application note describes the essential workings of an electrocardiogram (ECG). It discussesfactors that disrupt the ECG signals and make reliable, highly-accurate electrical characterization difficult. Theindustry-standard solution for ECG electrical characterization, which uses an analog front-end and ADCcombination, is explained. The article then introduces the MAX11040 simultaneous-sampling, sigma-deltaADC as a compelling, highly integrated solution that eliminates the need for the AFE, and saves both spaceand cost for the application.
上傳時間： 2013-12-23
上傳用戶：sssl
Who has never experienced oscillations issues when using an operational amplifier? Opampsare often used in a simple voltage follower configuration. However, this is not the bestconfiguration in terms of capacitive loading and potential risk of oscillations.Capacitive loads have a big impact on the stability of operational amplifier-basedapplications. Several compensation methods exist to stabilize a standard op-amp. Thisapplication note describes the most common ones, which can be used in most cases.The general theory of each compensation method is explained, and based on this, specific
上傳時間： 2013-10-28
上傳用戶：chenbhdt
Photodiodes can be broken into two categories: largearea photodiodes with their attendant high capacitance(30pF to 3000pF) and smaller area photodiodes withrelatively low capacitance (10pF or less). For optimalsignal-to-noise performance, a transimpedance amplifi erconsisting of an inverting op amp and a feedback resistoris most commonly used to convert the photodiode currentinto voltage. In low noise amplifi er design, large areaphotodiode amplifi ers require more attention to reducingop amp input voltage noise, while small area photodiodeamplifi ers require more attention to reducing op amp inputcurrent noise and parasitic capacitances.
上傳時間： 2013-10-28
上傳用戶：hanbeidang
This note describes some of the unique IC design techniques incorporated into a fast, monolithic power buffer, the LT1010. Also, some application ideas are described such as capacitive load driving, boosting fast op amp output current and power supply circuits.
上傳時間： 2013-11-12
上傳用戶：671145514
Abstract: We can apply a BiCMOS integrated circuit with only resistors and no transistors to solve adifficult design problem. The mythically perfect operational amplifier's gain and temperature coefficient aredependent on external resistor values. Maxim precision resistor arrays are manufactured together on asingle die and then automatically trimmed, to ensure close ratio matching. This guarantees that theoperational amplifier (op amp) gain and temperature coefficient are predictable and reliable, even withlarge production volumes.
上傳時間： 2014-11-30
上傳用戶：ynzfm
Abstract: Rail splitting is creating an artificial virtual ground as a reference voltage. It is used to set the signalto match the op amp's "sweet spot." An op amp has the most linear- and distortion-free qualities at that sweetspot. Typically, the sweet spot occurs near the center between the single power rail and ground. In the case ofa number of signals, the virtual ground can control channel DC errors when multiplexing or switching thesignals.
上傳時間： 2013-10-23
上傳用戶：wushengwu
針對科研實驗中對拉壓千斤頂加載過程控制的需要，采用ATmega128單片機控制步進電機進而實現對執行系統的電動泵站實行自動控制。對力和位移的數據采集與處理及用步進電機控制電動泵站手柄的技術細節作了重點描述。通過單片機的A/D變換器對AMP放大模塊采集的電橋信號作量化處理，千斤頂的操控手柄位置依電動油泵閥門開啟的方向和大小作若干定位，單片機根據力或位移傳感器信號，實時控制步進電機驅動手柄旋轉到相應操控位置。 Abstract: This article describes the use of ATmega128 AVR microcontroller series of DBS electric pumping stations and QF100/200 separate twoway hydraulic jack to automate the process of manipulating the work of the technical content. Articles on force and displacement data acquisition and processing， and stepper motor control electric pump with the handle of the key technical details were described. Through the MCU’s A / D converter module is collected on the AMP amplification quantify the signal bridge， jack handle position control valve opening according to the direction of electric pumps for a number of positioning and size of the microcontroller based on force or displacement sensor signals， real-time control stepper motor drive control handle rotate to the appropriate location.
上傳時間： 2014-01-16
上傳用戶：hasan2015
