模擬集成電路的設計與其說是一門技術，還不如說是一門藝術。它比數字集成電路設計需要更嚴格的分析和更豐富的直覺。嚴謹堅實的理論無疑是嚴格分析能力的基石，而設計者的實踐經驗無疑是誕生豐富直覺的源泉。這也正足初學者對學習模擬集成電路設計感到困惑并難以駕馭的根本原因。.美國加州大學洛杉機分校(UCLA)Razavi教授憑借著他在美國多所著名大學執教多年的豐富教學經驗和在世界知名頂級公司(AT&T，Bell Lab，HP)卓著的研究經歷為我們提供了這本優秀的教材。本書自2000午出版以來得到了國內外讀者的好評和青睞，被許多國際知名大學選為教科書。同時，由于原著者在世界知名頂級公司的豐富研究經歷，使本書也非常適合作為CMOS模擬集成電路設計或相關領域的研究人員和工程技術人員的參考書。... 本書介紹模擬CMOS集成電路的分析與設計。從直觀和嚴密的角度闡述了各種模擬電路的基本原理和概念，同時還闡述了在SOC中模擬電路設計遇到的新問題及電路技術的新發展。本書由淺入深，理論與實際結合，提供了大量現代工業中的設計實例。全書共18章。前10章介紹各種基本模塊和運放及其頻率響應和噪聲。第11章至第13章介紹帶隙基準、開關電容電路以及電路的非線性和失配的影響，第14、15章介紹振蕩器和鎖相環。第16章至18章介紹MOS器件的高階效應及其模型、CMOS制造工藝和混合信號電路的版圖與封裝。 1 Introduction to Analog Design 2 Basic MOS Device Physics 3 Single-Stage Amplifiers 4 Differential Amplifiers 5 Passive and Active Current Mirrors 6 Frequency Response of Amplifiers 7 Noise 8 FEEDBACK 9 Operational Amplifiers 10 Stability and Frequency Compensation 11 Bandgap References 12 Introduction to Switched-Capacitor Circuits 13 Nonlinearity and Mismatch 14 Oscillators 15 Phase-Locked Loops 16 Short-Channel Effects and Device Models 17 CMOS Processing Technology 18 Layout and Packaging
上傳時間： 2014-12-23
上傳用戶：杜瑩12345
本文將接續介紹電源與功率電路基板，以及數字電路基板導線設計。寬帶與高頻電路基板導線設計a.輸入阻抗1MHz，平滑性(flatness)50MHz 的OP增幅器電路基板圖26 是由FET 輸入的高速OP 增幅器OPA656 構成的高輸入阻抗OP 增幅電路，它的gain取決于R1、R2，本電路圖的電路定數為2 倍。此外為改善平滑性特別追加設置可以加大噪訊gain，抑制gain-頻率特性高頻領域時峰值的R3。圖26 高輸入阻抗的寬帶OP增幅電路圖27 是高輸入阻抗OP 增幅器的電路基板圖案。降低高速OP 增幅器反相輸入端子與接地之間的浮游容量非常重要，所以本電路的浮游容量設計目標低于0.5pF。如果上述部位附著大浮游容量的話，會成為高頻領域的頻率特性產生峰值的原因，嚴重時頻率甚至會因為FEEDBACK 阻抗與浮游容量，造成FEEDBACK 信號的位相延遲，最后導致頻率特性產生波動現象。此外高輸入阻抗OP 增幅器輸入部位的浮游容量也逐漸成為問題，圖27 的電路基板圖案的非反相輸入端子部位無full ground設計，如果有外部噪訊干擾之虞時，接地可設計成網格狀(mesh)。圖28 是根據圖26 制成的OP 增幅器Gain－頻率特性測試結果，由圖可知即使接近50MHz頻率特性非常平滑，-3dB cutoff頻率大約是133MHz。
標簽： PCB
上傳時間： 2013-11-13
上傳用戶：hebanlian
Abstract: A resistive FEEDBACK network is often used to set the output voltage of a power supply. A mechanical potentiometer (pot)conveniently solves the problem of adjusting a power supply. For easier automatic calibration, a mechanical pot can be replaced witha digital pot. This application note presents a calibration solution that uses a digital pot, because digipots are smaller, do not movewith age or vibration, and can be recalibrated remotely. This proposed solution reduces the susceptibility of the system to thetolerance of the digital pot's end-to-end resistance, making the solution optimal fordesigners. This application note also explainssome of the equations required to calculate the resistor chain values and to use a digital pot in this way. A spreadsheet withstandard reisistor values is available for easy calculations.
上傳時間： 2013-10-31
上傳用戶：caiguoqing
While simplicity and high effi ciency (for cool running) areno longer optional features in isolated power supplies, itis traditionally diffi cult to achieve both. Achieving higheffi ciency often requires the use of advanced topologiesand home-brewed secondary synchronous rectifi cationschemes once reserved only for higher power applications.This only adds to the parts count and to the designcomplexity associated with the reference and optocouplercircuits typically used to maintain isolation. Fortunately, abreakthrough IC makes it possible to achieve both high efficiency and simplicity in a synchronous fl yback topology.The LT®3825 simplifi es and improves the performance oflow voltage, high current fl yback supplies by providingprecise synchronous rectifi er timing and eliminating theneed for optocoupler FEEDBACK while maintaining excellentregulation and superior loop response.
上傳時間： 2013-10-16
上傳用戶：wayne595
Telecommunication, satellite links and set-top boxes allrequire tuning a high frequency oscillator. The actualtuning element is a varactor diode, a 2-terminal device thatchanges capacitance as a function of reverse bias voltage.1 The oscillator is part of a frequency synthesizingloop, as detailed in Figure 1. A phase locked loop (PLL)compares a divided down representation of the oscillatorwith a frequency reference. The PLL’s output is levelshifted to provide the high voltage necessary to bias thevaractor, which closes a FEEDBACK loop by voltage tuningthe oscillator. This loop forces the voltage controlledoscillator (VCO) to operate at a frequency determined bythe frequency reference and the divider’s division ratio.
上傳時間： 2013-12-20
上傳用戶：ABCDE
<Almost since the introduction of microcontrollers as electronic components there always has been an oscillatorcircuit on the device to make it work. From application point of view only some external components wererequired to make it work. However, to make sure that it will always work required more effort. This report is basedon FEEDBACK from the market from customers applying 8-bit mircrocontrollers.>
標簽： oscillators X-tal bit mic
上傳時間： 2013-11-12
上傳用戶：穿著衣服的大衛
This application note describes how to build a system that can be used for determining theoptimal phase shift for a Double Data Rate (DDR) memory FEEDBACK clock. In this system, theDDR memory is controlled by a controller that attaches to either the OPB or PLB and is used inan embedded microprocessor application. This reference system also uses a DCM that isconfigured so that the phase of its output clock can be changed while the system is running anda GPIO core that controls that phase shift. The GPIO output is controlled by a softwareapplication that can be run on a PowerPC® 405 or Microblaze™ microprocessor.
上傳時間： 2013-10-15
上傳用戶：euroford
機電類比法是一種把機械量通過一定的計算等效類比為電量的方法，其在對電子機械系統的分析中應用非常廣泛。它能夠把一個較復雜的機械系統類比為我們熟知的電路系統來進行分析，從而使問題的分析得到簡化。本文通過對振弦式傳感器的分析介紹了機電類比法，并對使用電路進行了相關的分析。 Summary：The electromechanical analogy is assort of analysis which is to analogize the mechanical system by using circuit system , it applied widely in the filed of analysis the electronic-mechanical system. The analysis can take a complex mechanical system analogous to a circuitry that we well-known, which can simplify the problems. In the paper, the electro-mechanical analogy method is briefly introduced by analysis the vibrating wire sensor，and have a correlation analysis about the circuit we used.關鍵詞： 機電類比法 振弦式傳感器 頻率 振蕩 反饋Keyword：electro-mechanical analogy method，vibrating wire sensor，frequency, oscillation, FEEDBACK 0 引言振弦式傳感器是屬于頻率式傳感器的一種。所謂頻率式傳感器就是能直接將被測量轉換為振動頻率信號的傳感器，這類傳感器一般是通過測量振弦、振筒、振梁、振膜等彈性振體或石英晶體諧振器的固有諧振頻率來達到測量引起諧振頻率變化的被測非電量的目的，其也稱為諧振式傳感器[1]。在分析該類傳感器中，由于其涉及到頻率，就容易讓人聯想到在電子技術中接觸到的RLC振蕩電路。因此可以嘗試著用類比的方法使之對應起來分析,即機電類比法分析。
上傳時間： 2013-11-16
上傳用戶：paladin
This application note describes how to build a system that can be used for determining theoptimal phase shift for a Double Data Rate (DDR) memory FEEDBACK clock. In this system, theDDR memory is controlled by a controller that attaches to either the OPB or PLB and is used inan embedded microprocessor application. This reference system also uses a DCM that isconfigured so that the phase of its output clock can be changed while the system is running anda GPIO core that controls that phase shift. The GPIO output is controlled by a softwareapplication that can be run on a PowerPC® 405 or Microblaze™ microprocessor.
上傳時間： 2014-11-26
上傳用戶：erkuizhang
本文將接續介紹電源與功率電路基板，以及數字電路基板導線設計。寬帶與高頻電路基板導線設計a.輸入阻抗1MHz，平滑性(flatness)50MHz 的OP增幅器電路基板圖26 是由FET 輸入的高速OP 增幅器OPA656 構成的高輸入阻抗OP 增幅電路，它的gain取決于R1、R2，本電路圖的電路定數為2 倍。此外為改善平滑性特別追加設置可以加大噪訊gain，抑制gain-頻率特性高頻領域時峰值的R3。圖26 高輸入阻抗的寬帶OP增幅電路圖27 是高輸入阻抗OP 增幅器的電路基板圖案。降低高速OP 增幅器反相輸入端子與接地之間的浮游容量非常重要，所以本電路的浮游容量設計目標低于0.5pF。如果上述部位附著大浮游容量的話，會成為高頻領域的頻率特性產生峰值的原因，嚴重時頻率甚至會因為FEEDBACK 阻抗與浮游容量，造成FEEDBACK 信號的位相延遲，最后導致頻率特性產生波動現象。此外高輸入阻抗OP 增幅器輸入部位的浮游容量也逐漸成為問題，圖27 的電路基板圖案的非反相輸入端子部位無full ground設計，如果有外部噪訊干擾之虞時，接地可設計成網格狀(mesh)。圖28 是根據圖26 制成的OP 增幅器Gain－頻率特性測試結果，由圖可知即使接近50MHz頻率特性非常平滑，-3dB cutoff頻率大約是133MHz。
標簽： PCB
上傳時間： 2013-11-09
上傳用戶：z754970244
