針對使用硬件描述語言進行設計存在的問題，提出一種基于FPGA并采用DSP Builder作為設計工具的數字信號處理器設計方法。并按照Matlab/Simulink/DSP Builder/QuartusⅡ設計流程，設計了一個12階FIR 低通數字濾波器，通過Quartus 時序仿真及嵌入式邏輯分析儀SignalTapⅡ硬件測試對設計進行了驗證。結果表明，所設計的FIR 濾波器功能正確，性能良好。 Abstract: Aiming at the problems in designing DSP using HDL，a method of designing DSP based on FPGA which using DSP Builder as designed tool is pointed out.A 12-order low-pass FIR digital filter was designed according to the process of Matlab/Simulink/DSP Builder/QuartusⅡ, and the design was verified by the timing simulation based on QuartusⅡand practical test based on SignalTapⅡ. The result shows the designed filter is correct in function and good in performance.
上傳時間： 2013-11-17
上傳用戶：lo25643
在綜合分析諧波勵磁無刷同步發電機勵磁控制系統的基礎上,對其勵磁控制策略進行了研究,開發了一套基于DSP( TMS320F2812) 控制的新型柴油發電機勵磁控制系統,該系統采用參數自適應模糊PID 控制勵磁,選用交流采樣方式實時檢測各信號的瞬時特性,系統仿真結果以及在1 臺25 kW 工頻柴油發電機上的試驗結果證明了該控制器具有較好的電壓調節特性,系統穩態和暫態性能完全滿足發電機對勵磁系統的要求。關鍵詞:勵磁調節;模糊PID 控制;數字信號處理器;交流采樣 Abstract :According to the general analysis of the excitation cont rol system of the harmonious wave excitation brushless synchronous generator and it s characteristics ,a new type of diesel generator excitation cont rol system based on DSP( TMS320F2812) was designed. An adaptive fuzzy PID cont rol of excitation is used in this system. To detect the t ransient characteristics of the signals in a timely manner ,AC sampling was applied.The system simulation result s and the testing result s f rom a 25 kW diesel generator (50 Hz) can prove that the voltage regulation characteristics of the excitation cont rol system are very well ,and both the steadyOstate performance and the t ransient performance of the generator are also good.Key words :excitation cont rol ;fuzzy PID cont rol ;digital signal processor (DSP) ;AC sampling
上傳時間： 2013-10-29
上傳用戶：fxf126@126.com
中文版詳情瀏覽：http://www.elecfans.com/emb/fpga/20130715324029.html Xilinx UltraScale:The Next-Generation Architecture for Your Next-Generation Architecture The Xilinx® UltraScale™ architecture delivers unprecedented levels of integration and capability with ASIC-class system- level performance for the most demanding applications. The UltraScale architecture is the industr y's f irst application of leading-edge ASIC architectural enhancements in an All Programmable architecture that scales from 20 nm planar through 16 nm FinFET technologies and beyond, in addition to scaling from monolithic through 3D ICs. Through analytical co-optimization with the X ilinx V ivado® Design Suite, the UltraScale architecture provides massive routing capacity while intelligently resolving typical bottlenecks in ways never before possible. This design synergy achieves greater than 90% utilization with no performance degradation. Some of the UltraScale architecture breakthroughs include: • Strategic placement (virtually anywhere on the die) of ASIC-like system clocks, reducing clock skew by up to 50% • Latency-producing pipelining is virtually unnecessary in systems with massively parallel bus architecture, increasing system speed and capability • Potential timing-closure problems and interconnect bottlenecks are eliminated, even in systems requiring 90% or more resource utilization • 3D IC integration makes it possible to build larger devices one process generation ahead of the current industr y standard • Greatly increased system performance, including multi-gigabit serial transceivers, I/O, and memor y bandwidth is available within even smaller system power budgets • Greatly enhanced DSP and packet handling The Xilinx UltraScale architecture opens up whole new dimensions for designers of ultra-high-capacity solutions.
標簽： UltraScale Xilinx 架構
上傳時間： 2013-11-13
上傳用戶：瓦力瓦力hong
SF-CY3 FPGA套件開發指南Ver6.00 （by特權同學）
上傳時間： 2013-10-22
上傳用戶：songnanhua
This application note covers the design considerations of a system using the performance features of the LogiCORE™ IP Advanced eXtensible Interface (AXI) Interconnect core. The design focuses on high system throughput through the AXI Interconnect core with F MAX and area optimizations in certain portions of the design. The design uses five AXI video direct memory access (VDMA) engines to simultaneously move 10 streams (five transmit video streams and five receive video streams), each in 1920 x 1080p format, 60 Hz refresh rate, and up to 32 data bits per pixel. Each VDMA is driven from a video test pattern generator (TPG) with a video timing controller (VTC) block to set up the necessary video timing signals. Data read by each AXI VDMA is sent to a common on-screen display (OSD) core capable of multiplexing or overlaying multiple video streams to a single output video stream. The output of the OSD core drives the DVI video display interface on the board. Performance monitor blocks are added to capture performance data. All 10 video streams moved by the AXI VDMA blocks are buffered through a shared DDR3 SDRAM memory and are controlled by a MicroBlaze™ processor. The reference system is targeted for the Virtex-6 XC6VLX240TFF1156-1 FPGA on the Xilinx® ML605 Rev D evaluation board
上傳時間： 2013-11-14
上傳用戶：fdmpy
Linux移植之Step By Step_V4.1
上傳時間： 2013-10-15
上傳用戶：13033095779
文章對美國升級臺灣F-16機載多功能雷達的技術進行了研究。首先介紹了有源電掃相控陣技術，該技術是提高雷達性能的關鍵所在。其次對多普勒銳化和合成孔徑技術進行了深入的討論，研究表明合成孔徑技術能更好地提高成像效果。最后分析了升級F-16帶來的不足，說明升級不能阻止國家的統一大業。
上傳時間： 2013-11-14
上傳用戶：古谷仁美
為滿足無線網絡技術具有低功耗、節點體積小、網絡容量大、網絡傳輸可靠等技術要求，設計了一種以MSP430單片機和CC2420射頻收發器組成的無線傳感節點。通過分析其節點組成，提出了ZigBee技術中的幾種網絡拓撲形式，并研究了ZigBee路由算法。針對不同的傳輸要求形式選用不同的網絡拓撲形式可以盡大可能地減少系統成本。同時針對不同網絡選用正確的ZigBee路由算法有效地減少了網絡能量消耗，提高了系統的可靠性。應用試驗表明，采用ZigBee方式通信可以提高傳輸速率且覆蓋范圍大，與傳統的有線通信方式相比可以節約40%左右的成本。 Abstract: To improve the proposed technical requirements such as low-ower， small nodes， large capacity and reliable network transmission， wireless sensor nodes based on MSP430 MCU and CC2420 RF transceiver were designed. This paper provided network topology of ZigBee technology by analysing the component of the nodes and researched ZigBee routing algorithm. Aiming at different requirements of transmission mode to choose the different network topologies form can most likely reduce the system cost. And aiming at different network to choose the correct ZigBee routing algorithm can effectively reduced the network energy consumption and improved the reliability of the system. Results show that the communication which used ZigBee mode can improve the transmission rate， cover more area and reduce 40% cost compared with traditional wired communications mode.
上傳時間： 2013-10-09
上傳用戶：robter
本軟件是關于MAX338, MAX339的英文數據手冊：MAX338, MAX339 8通道/雙4通道、低泄漏、CMOS模擬多路復用器 The MAX338/MAX339 are monolithic, CMOS analog multiplexers (muxes). The 8-channel MAX338 is designed to connect one of eight inputs to a common output by control of a 3-bit binary address. The dual, 4-channel MAX339 is designed to connect one of four inputs to a common output by control of a 2-bit binary address. Both devices can be used as either a mux or a demux. On-resistance is 400Ω max, and the devices conduct current equally well in both directions. These muxes feature extremely low off leakages (less than 20pA at +25°C), and extremely low on-channel leakages (less than 50pA at +25°C). The new design offers guaranteed low charge injection (1.5pC typ) and electrostatic discharge (ESD) protection greater than 2000V, per method 3015.7. These improved muxes are pin-compatible upgrades for the industry-standard DG508A and DG509A. For similar Maxim devices with lower leakage and charge injection but higher on-resistance, see the MAX328 and MAX329.
上傳時間： 2013-11-12
上傳用戶：18711024007
中文版詳情瀏覽：http://www.elecfans.com/emb/fpga/20130715324029.html Xilinx UltraScale:The Next-Generation Architecture for Your Next-Generation Architecture The Xilinx® UltraScale™ architecture delivers unprecedented levels of integration and capability with ASIC-class system- level performance for the most demanding applications. The UltraScale architecture is the industr y's f irst application of leading-edge ASIC architectural enhancements in an All Programmable architecture that scales from 20 nm planar through 16 nm FinFET technologies and beyond, in addition to scaling from monolithic through 3D ICs. Through analytical co-optimization with the X ilinx V ivado® Design Suite, the UltraScale architecture provides massive routing capacity while intelligently resolving typical bottlenecks in ways never before possible. This design synergy achieves greater than 90% utilization with no performance degradation. Some of the UltraScale architecture breakthroughs include: • Strategic placement (virtually anywhere on the die) of ASIC-like system clocks, reducing clock skew by up to 50% • Latency-producing pipelining is virtually unnecessary in systems with massively parallel bus architecture, increasing system speed and capability • Potential timing-closure problems and interconnect bottlenecks are eliminated, even in systems requiring 90% or more resource utilization • 3D IC integration makes it possible to build larger devices one process generation ahead of the current industr y standard • Greatly increased system performance, including multi-gigabit serial transceivers, I/O, and memor y bandwidth is available within even smaller system power budgets • Greatly enhanced DSP and packet handling The Xilinx UltraScale architecture opens up whole new dimensions for designers of ultra-high-capacity solutions.
標簽： UltraScale Xilinx 架構
上傳時間： 2013-11-21
上傳用戶：wxqman
