This errata sheet describes Both the known functional problems and anydeviations from the electrical specifications known at the release date ofthis document.Each deviation is assigned a number and its history is tracked in a table atthe end of the document.
上傳時間： 2014-12-31
上傳用戶：thuyenvinh
本軟件是關于MAX338, MAX339的英文數據手冊：MAX338, MAX339 8通道/雙4通道、低泄漏、CMOS模擬多路復用器 The MAX338/MAX339 are monolithic, CMOS analog multiplexers (muxes). The 8-channel MAX338 is designed to connect one of eight inputs to a common output by control of a 3-bit binary address. The dual, 4-channel MAX339 is designed to connect one of four inputs to a common output by control of a 2-bit binary address. Both devices can be used as either a mux or a demux. On-resistance is 400Ω max, and the devices conduct current equally well in Both directions. These muxes feature extremely low off leakages (less than 20pA at +25°C), and extremely low on-channel leakages (less than 50pA at +25°C). The new design offers guaranteed low charge injection (1.5pC typ) and electrostatic discharge (ESD) protection greater than 2000V, per method 3015.7. These improved muxes are pin-compatible upgrades for the industry-standard DG508A and DG509A. For similar Maxim devices with lower leakage and charge injection but higher on-resistance, see the MAX328 and MAX329.
上傳時間： 2013-11-12
上傳用戶：18711024007
This book is about the digital logic design of microprocessors. It is intended to provide Both an understanding of the basic principles of digital logic design, and how these fundamental principles are applied in the building of complex microprocessor circuits using current technologies.
上傳時間： 2013-10-14
上傳用戶：leyesome
通過以太網遠程配置Nios II 處理器 應用筆記 Firmware in embedded hardware systems is frequently updated over the Ethernet. For embedded systems that comprise a discrete microprocessor and the devices it controls, the firmware is the software image run by the microprocessor. When the embedded system includes an FPGA, firmware updates include updates of the hardware image on the FPGA. If the FPGA includes a Nios® II soft processor, you can upgrade Both the Nios II processor—as part of the FPGA image—and the software that the Nios II processor runs, in a single remote configuration session.
上傳時間： 2013-11-22
上傳用戶：chaisz
In the past decade, the size and complexity of manyFPGA designs exceeds the time and resourcesavailable to most design teams, making the use andreuse of Intellectual Property (IP) imperative.However, integrating numerous IP blocks acquiredfrom Both internal and external sources can be adaunting challenge that often extends, rather thanshortens, design time. As today's designs integrateincreasing amounts of functionality, it is vital thatdesigners have access to proven, up-to-date IP fromreliable sources.
上傳時間： 2013-11-11
上傳用戶：csgcd001
Today’s digital systems combine a myriad of chips with different voltage configurations.Designers must interface 2.5V processors with 3.3V memories—Both RAM and ROM—as wellas 5V buses and multiple peripheral chips. Each chip has specific power supply needs. CPLDsare ideal for handling the multi-voltage interfacing, but do require forethought to ensure correctoperation.
上傳時間： 2013-11-10
上傳用戶：yy_cn
Design techniques for electronic systems areconstantly changing. In industries at the heart of thedigital revolution, this change is especially acute.Functional integration, dramatic increases incomplexity, new standards and protocols, costconstraints, and increased time-to-market pressureshave bolstered Both the design challenges and theopportunities to develop modern electronic systems.One trend driving these changes is the increasedintegration of core logic with previously discretefunctions to achieve higher performance and morecompact board designs.
上傳時間： 2013-11-23
上傳用戶：kangqiaoyibie
Digital cameras have become increasingly popular over the last few years. Digital imagingtechnology has grown to new markets including cellular phones and PDA devices. With thediverse marketplace, a variety of imaging technology must be available. Imaging technologyhas expanded to include Both charge-coupled device (CCD) and CMOS image sensors.
標簽： CoolRunner-II XAPP CPLD 390
上傳時間： 2013-10-16
上傳用戶：18710733152
The LogiCORE™ GTP Wizard automates the task of creating HDL wrappers to configure the high-speed serial GTP transceivers in Virtex™-5 LXT and SXT devices. The menu-driven interface allows one or more GTP transceivers to be configured using pre-definedtemplates for popular industry standards, or from scratch, to support a wide variety of custom protocols.The Wizard produces a wrapper, an example design, and a testbench for rapid integration and verification of the serial interface with your custom function Features• Creates customized HDL wrappers to configureVirtex-5 RocketIO™ GTP transceivers• Users can configure Virtex-5 GTP transceivers toconform to industry standard protocols usingpredefined templates, or tailor the templates forcustom protocols• Included protocol templates provide support for thefollowing specifications: Aurora, CPRI, FibreChannel 1x, Gigabit Ethernet, HD-SDI, OBSAI,OC3, OC12, OC48, PCI Express® (PCIe®), SATA,SATA II, and XAUI• Automatically configures analog settings• Each custom wrapper includes example design, testbench; and Both implementation and simulation scripts
標簽： Transceiver Virtex Wizar GTP
上傳時間： 2013-10-20
上傳用戶：dave520l
Integrated EMI/Thermal Design forSwitching Power SuppliesWei ZhangThesis submitted to the Faculty of theVirginia Polytechnic Institute and State Universityin partial fulfillment of the requirements for the degree of Integrated EMI/Thermal Design forSwitching Power SuppliesWei Zhang(ABSTRACT)This work presents the modeling and analysis of EMI and thermal performancefor switch power supply by using the CAD tools. The methodology and design guidelinesare developed.By using a boost PFC circuit as an example, an equivalent circuit model is builtfor EMI noise prediction and analysis. The parasitic elements of circuit layout andcomponents are extracted analytically or by using CAD tools. Based on the model, circuitlayout and magnetic component design are modified to minimize circuit EMI. EMI filtercan be designed at an early stage without prototype implementation.In the second part, thermal analyses are conducted for the circuit by using thesoftware Flotherm, which includes the mechanism of conduction, convection andradiation. Thermal models are built for the components. Thermal performance of thecircuit and the temperature profile of components are predicted. Improved thermalmanagement and winding arrangement are investigated to reduce temperature.In the third part, several circuit layouts and inductor design examples are checkedfrom Both the EMI and thermal point of view. Insightful information is obtained.
上傳時間： 2013-11-16
上傳用戶：萍水相逢
<input id="saium"></input>
<strike id="saium"></strike>
<strike id="saium"></strike>