Multiple-voltage electronics systems often requirecomplex supply voltage tracking or sequencing, whichif not met, can result in system faults or even permanentfailures in the fi eld. The design diffi culties in meetingthese requirements are often compounded in distributedpowerarchitectures where point-of-load (POL) DC/DCconverters or linear regulators are scattered across PCboard space, sometimes on different board planes. Theproblem is that power supply circuitry is often the lastcircuitry to be designed into the board, and it must beshoehorned into whatever little board real estate is left.Often, a simple, drop-in, fl exible solution is needed tomeet these requirements.
上傳時間： 2013-10-08
上傳用戶：15071087253
DC/DC 升壓IC：The FP6291 is a current mode boost DC-DC converter. Its PWM circuitry with built-in 0.25 Ω power MOSFET make this regulator highly power efficient. The internal compensation network also minimizes as much as 6 external component counts. The non-inverting input of error amplifier connects to a 0.6V precision reference voltage and internal soft-start function can reduce the inrush current. The FP6291 is available in the SOT23-6L package and provides space-saving PCB for the application fields.
上傳時間： 2013-11-07
上傳用戶：3294322651
The power appetite of large TFT-LCDs appears to beinsatiable. Power supplies must feed increasing numbersof transistors and improved display resolutions, and doso without taking much space.
上傳時間： 2014-12-24
上傳用戶：小小小熊
Piezoelectric motors are used in digital cameras for autofocus,zooming and optical image stabilization. Theyare relatively small, lightweight and effi cient, but theyalso require a complicated driving scheme. Traditionally,this challenge has been met with the use ofseparatecircuits, including a step-up converter and an oversizedgeneric full-bridge drive IC. The resulting high componentcount and large board space are especially problematicin the design of cameras for ever shrinking cell phones.The LT®3572 solves these problems by combining astep-up regulator and a dual full-bridge driver in a 4mm× 4mm QFN package. Figure 1 shows a typical LT3572Piezo motor drive circuit. A step-up converter is usedto generate 30V from a low voltage power source suchas a Li-Ion battery or any input power source within thepart’s wide input voltage range of 2.7V to 10V. The highoutput voltage of the step-up converter, adjustable upto 40V, is available for the drivers at the VOUT pin. Thedrivers operate in a full-bridge fashion, where the OUTAand OUTB pins are the same polarity as the PWMA andPWMB pins, respectively, and the OUTA and OUTB pinsare inverted from PWMA and PWMB, respectively. Thestep-up converter and both Piezo drivers have their ownshutdown control. Figure 2 shows a typical layout
上傳時間： 2013-11-18
上傳用戶：hulee
Alkaline batteries are convenient because they’re easy tofi nd and relatively inexpensive, making them the powersource of choice for portable instruments and devicesused for outdoor recreation. Their long shelf life alsomakes them an excellent choice for emergency equipmentthat may see infrequent use but must be ready to go on amoment’s notice. It is important that the DC/DC convertersin portable devices operate over the widest possiblebattery voltage range to extend battery run time, and thussave the user from frequent battery replacement.
上傳時間： 2014-12-24
上傳用戶：569342831
Avalanche photo diode (APD) receiver modules arewidely used in fi ber optic communication systems. AnAPD module contains the APD and a signal conditioningamplifi er, but is not completely self contained. It stillrequires signifi cant support circuitry including a highvoltage, low noise power supply and a precision currentmonitor to indicate the signal strength. The challenge issqueezing this support circuitry into applications withlimited board space. The LT®3482 addresses this challengeby integrating a monolithic DC/DC step-up converter andan accurate current monitor. The LT3482 can supportup to a 90V APD bias voltage, and the current monitorprovides better than 10% accuracy over four decades ofdynamic range (250nA to 2.5mA).
上傳時間： 2014-01-18
上傳用戶：wenyuoo
Today’s computer, datacom, and telecom systems demandpower supplies that are effi cient, respond quicklyto load transients and accurately regulate the voltageat the load. For example, load current can be measuredby using the inductor DCR, thus eliminating the needfor a dedicated sense resistor. Inductor DCR sensingincreases effi ciency—especially at heavy load—whilereducing component cost and required board space.The LTC®3856 single-output 2-phase synchronous buckcontroller improves the accuracy of inductor DCR sensingby compensating for changes in DCR due to temperature.
上傳時間： 2013-11-05
上傳用戶：guobing703
As environmental concerns over traditional lighting increaseand the price of LEDs decreases, high power LEDsare fast becoming a popular lighting solution for offl ineapplications. In order to meet the requirements of offl inelighting—such as high power factor, high effi ciency, isolationand TRIAC dimmer compatibility—prior LED driversused many external discrete components, resulting incumbersome solutions. The LT®3799 solves complexity,space and performance problems by integrating all therequired functions for offl ine LED lighting.
上傳時間： 2013-10-13
上傳用戶：dongqiangqiang
Abstract: This article discusses future trends in the design of smartphones and other consumer products. The discussion focuses onthe importance of integration, which saves valuable PCB space and drives down costs.
上傳時間： 2014-01-13
上傳用戶：lhw888
For a variety of reasons, it is desirable to charge batteriesas rapidly as possible. At the same time, overchargingmust be limited to prolong battery life. Such limitation ofovercharging depends on factors such as the choice ofcharge termination technique and the use of multi-rate/multi-stage charging schemes. The majority of batterycharger ICs available today lock the user into one fixedcharging regimen, with at best a limited number ofcustomization options to suit a variety of application needsor battery types. The LTC®1325 addresses these shortcomingsby providing the user with all the functionalblocks needed to implement a simple but highly flexiblebattery charger (see Figure 1) which not only addressesthe issue of charging batteries but also those of batteryconditioning and capacity monitoring.
上傳時間： 2013-10-19
上傳用戶：royzhangsz
