The following Philips LPC2k CAN examples in this directory were provided by ESAcademy. LPC2_CANAll_V110: Receives all CAN messages in a receive queue. LPC2_CANFull_V110: Uses Full-CAN-like reception filtering. LPC2_CANBlinky_V130: Minimal example of MicroCANopen, uses Full-CAN-like reception filtering and implements both Rx and Tx Interrupt Service Routines.
標簽： ESAcademy following directory examples
上傳時間： 2013-12-13
上傳用戶：牛津鞋
The following Philips LPC2k CAN examples in this directory were provided by ESAcademy. LPC2_CANAll_V110: Receives all CAN messages in a receive queue. LPC2_CANFull_V110: Uses Full-CAN-like reception filtering. LPC2_CANBlinky_V130: Minimal example of MicroCANopen, uses Full-CAN-like reception filtering and implements both Rx and Tx Interrupt Service Routines.
標簽： ESAcademy following directory examples
上傳時間： 2014-01-06
上傳用戶：zukfu
A system simulation environment in Matlab/Simulink of RFID is constructed in this paper. Special attention is emphasized on the analog/RF circuit.Negative effects are concerned in the system model,such as phase noise of the local oscillator,TX-RX coupling,reflection of the environment, AWGN noise,DC offset,I/Q mismatch,etc.Performance of the whole system can be evaluated by changing the coding method,parameters of building blocks,and operation distance.Finally,some simulation results are presented in this paper.
標簽： environment constructed simulation Simulink
上傳時間： 2014-01-09
上傳用戶：zhangliming420
smsc911x 網卡驅動 This the users/programmers guide for the LAN911x Linux Driver The following sections can be found below * Revision History * Files * Features * Driver Parameters * Rx Performance Tuning * Tested Platforms * Rx Code Path * Tx Code Path * Platform Interface Descriptions
標簽： 911x programmers 911 following
上傳時間： 2014-12-02
上傳用戶：sssl
基于OFDM的無線寬帶系統仿真It contains mainly two parts, i.e. link-level simulator and system-level simulator. Link-level simulator focus on a single-cell single-user scenario, where signal is transmitted from tx, and estimated at rx. Comparing the difference in tx/rx signal, the error rate can be found out. The output of the link-level simulator is the BLER/BER vs. SNR mapping table, that can be used for the system-level simulation. System-level simulator focus on a multi-cell multi-user scenario. For the sake of simplicity, it takes the mapping table aquired in the link-level simulation, measure the actural SNR, and finds the corresponding error rate.
標簽： simulator i.e. system-level link-level
上傳時間： 2016-03-15
上傳用戶：xsnjzljj
在c++builder環境下一個串口通信程序，包括界面的設計和串口通信函數的設計，實現了串口通信。在文件夾TX-RX中。
上傳時間： 2013-12-10
上傳用戶：ippler8
NRF905驅動代碼 // The content of this struct is nRF905 s initialize data. // CH_NO=1 433MHZ Normal Opration,No Retrans RX,TX Address is 4 Bytes // RX TX Payload Width is 32 Bytes Disable Extern Clock Fosc=16MHZ // 8 Bits CRC And enable
標簽： initialize 905 content Normal
上傳時間： 2013-12-16
上傳用戶：lanjisu111
一個UWB仿真程序包，里面包含信號生成，信道模擬，Tx/Rx等模塊。M-file
上傳時間： 2016-05-22
上傳用戶：xiaoxiang
(1) 315、433、868、915Mh的ISM 和SRD頻段 (2) 最高工作速率500kbps，支持2-FSK、GFSK和MSK調制方式 (3) 高靈敏度（1.2kbps下-110dDm，1％數據包誤碼率） (4) 內置硬件CRC 檢錯和點對多點通信地址控制 (5) 較低的電流消耗（RX中，15.6mA，2.4kbps,433MHz） (6) 可編程控制的輸出功率，對所有的支持頻率可達+10dBm (7) 支持低功率電磁波激活功能 (8) 支持傳輸前自動清理信道訪問（CCA），即載波偵聽系統 (9) 快速頻率變動合成器帶來的合適的頻率跳躍系統 (10) 模塊可軟件設地址，軟件編程非常方便 (11) 標準DIP間距接口，便于嵌入式應用 (12) 單獨的64字節RX和TX數據FIFO
上傳時間： 2016-06-21
上傳用戶：anng
Description: This program demonstrates a half-duplex 9600-baud UART using // Timer_A3 using no XTAL and an external resistor for DCO ROSC. DCO used for // TACLK UART baud generation. The program will wait in LPM4, echoing back // a received character using 8N1 protocol. On valid RX character, the // character is echoed back. // Using a 100k resistor on ROSC, with default DCO setting, set DCOCLK ~ 2MHz. // ACLK = n/a, MCLK = SMCLK ~2MHz DCOCLK
標簽： using demonstrates Description half-duplex
上傳時間： 2014-01-14
上傳用戶：cuiyashuo
