針對目前使用的RS232接口數字化B超鍵盤存在PC主機啟動時不能設置BIOS，提出一種PS2鍵盤的設計方法。基于W78E052D單片機，采用8通道串行A/D轉換器設計了8個TGC電位器信息采集電路，電位器位置信息以鍵盤掃描碼序列形式發送，正交編碼器信號通過XC9536XL轉換為單片機可接收的中斷信號，軟件接收到中斷信息后等效處理成按鍵。結果表明，在滿足開機可設置BIOS同時，又可實現超聲特有功能，不需要專門設計驅動程序，接口簡單，成本低。 Abstract: Aiming at the problem of the digital ultrasonic diagnostic imaging system keyboard with RS232 interface currently used couldn?蒺t set the BIOS when the PC boot， this paper proposed a design method of PS2 keyboards. Based on W78E052D microcontroller，designed eight TGC potentiometers information acquisition circuit with 8-channel serial A/D converter， potentiometer position information sent out with keyboard scan code sequentially.The control circuit based on XC9536 CPLD is used for converting the mechanical actions of the encoders into the signals that can be identified by the MCU， software received interrupt information and equivalently treatmented as key. The results show that the BIOS can be set to meet the boot， ultrasound specific functionality can be achieved at the same time， it does not require specially designed driver，the interface is simple and low cost.
上傳時間： 2013-10-10
上傳用戶：asdfasdfd
以C8051F020為核心處理器，設計無線傳感器網絡數據采集系統。系統采用SZ05-ADV型無線通訊模塊組建Zigbee無線網絡，結合嵌入式系統的軟硬件技術，完成終端節點的8路傳感器信號的數據采集。現場8路信號通過前端處理后，分別送入C8051F020的12位A/D轉換器進行轉換。經過精確處理、存儲后的現場數據，通過Zigbee無線網絡傳送到上位機，系統可達到汽車試驗中無線測試的目的。 Abstract: This paper designs a wireless sensor network system for data acquisition with C8051F020 as core processors.The system used SZ05-ADV wireless communication module，set up a Zigbee wireless network， combined with hardware and software technologies of embedded systems，completed the end-node 8-locale sensor signal data acquisition.Eight locale signals were sent separately into the 12-bit ADC of C8051F020 for conversion through front treatment.After accurate processing and storage，the locale data was transmitted to the host computer through Zigbee wireless.The system achieves the purpose of wireless testing in vehicle trial.
標簽： C8051F020 Zigbee 汽車測試 系統設計
上傳時間： 2013-11-23
上傳用戶：dsgkjgkjg
介紹一種簡單射頻識別系統設計。該設計包括閱讀器、應答器和線圈3部分。由單片機控制閱讀器向應答器發射無線信號，并接收應答器回送的信號，再通過分析回送信號識別物品。閱讀器和應答器之間以半雙工通信方式通信。 Abstract: A simple design of radio frequency identification system is given in this paper.The design includes reader,responder and winding.Through MCU，signals are sent to responder from reader，then corresponding signals are sent back. According to the analysis of the signals sent back，the objects can be identified.Half-duplex communication is adopted? between? reader? and? responder.
上傳時間： 2013-10-11
上傳用戶：plsee
The PCA9541 is a 2-to-1 I2C-bus master selector designed for high reliability dual masterI2C-bus applications where system operation is required, even when one master fails orthe controller card is removed for maintenance. The two masters (for example, primaryand back-up) are located on separate I2C-buses that connect to the same downstreamI2C-bus slave devices. I2C-bus commands are sent by either I2C-bus master and are usedto select one master at a time. Either master at any time can gain control of the slavedevices if the other master is disabled or removed from the system. The failed master isisolated from the system and will not affect communication between the on-line masterand the slave devices on the downstream I2C-bus.
上傳時間： 2013-10-09
上傳用戶：3294322651
三種方法讀取鍵值 使用者設計行列鍵盤介面，一般常採用三種方法讀取鍵值。 中斷式 在鍵盤按下時產生一個外部中斷通知CPU，並由中斷處理程式通過不同位址讀資料線上的狀態判斷哪個按鍵被按下。 本實驗採用中斷式實現使用者鍵盤介面。 掃描法 對鍵盤上的某一行送低電位，其他為高電位，然後讀取列值，若列值中有一位是低，表明該行與低電位對應列的鍵被按下。否則掃描下一行。 反轉法 先將所有行掃描線輸出低電位，讀列值，若列值有一位是低表明有鍵按下；接著所有列掃描線輸出低電位，再讀行值。 根據讀到的值組合就可以查表得到鍵碼。4x4鍵盤按4行4列組成如圖電路結構。按鍵按下將會使行列連成通路，這也是見的使用者鍵盤設計電路。 //-----------4X4鍵盤程序--------------// uchar keboard(void) { uchar xxa,yyb,i,key; if((PINC&0x0f)!=0x0f) //是否有按鍵按下 {delayms(1); //延時去抖動 if((PINC&0x0f)!=0x0f) //有按下則判斷 { xxa=~(PINC|0xf0); //0000xxxx DDRC=0x0f; PORTC=0xf0; delay_1ms(); yyb=~(PINC|0x0f); //xxxx0000 DDRC=0xf0; //復位 PORTC=0x0f; while((PINC&0x0f)!=0x0f) //按鍵是否放開 { display(data); } i=4; //計算返回碼 while(xxa!=0) { xxa=xxa>>1; i--; } if(yyb==0x80) key=i; else if(yyb==0x40) key=4+i; else if(yyb==0x20) key=8+i; else if(yyb==0x10) key=12+i; return key; //返回按下的鍵盤碼 } } else return 17; //沒有按鍵按下 }
上傳時間： 2013-11-12
上傳用戶：a673761058
This application note covers the design considerations of a system using the performance features of the LogiCORE™ IP Advanced eXtensible Interface (AXI) Interconnect core. The design focuses on high system throughput through the AXI Interconnect core with F MAX and area optimizations in certain portions of the design. The design uses five AXI video direct memory access (VDMA) engines to simultaneously move 10 streams (five transmit video streams and five receive video streams), each in 1920 x 1080p format, 60 Hz refresh rate, and up to 32 data bits per pixel. Each VDMA is driven from a video test pattern generator (TPG) with a video timing controller (VTC) block to set up the necessary video timing signals. Data read by each AXI VDMA is sent to a common on-screen display (OSD) core capable of multiplexing or overlaying multiple video streams to a single output video stream. The output of the OSD core drives the DVI video display interface on the board. Performance monitor blocks are added to capture performance data. All 10 video streams moved by the AXI VDMA blocks are buffered through a shared DDR3 SDRAM memory and are controlled by a MicroBlaze™ processor. The reference system is targeted for the Virtex-6 XC6VLX240TFF1156-1 FPGA on the Xilinx® ML605 Rev D evaluation board
上傳時間： 2013-11-14
上傳用戶：fdmpy
1 Communication Protocol (Computer as master) The communication protocol describes here allows your computer to access 4096 internal registers (W0000-W4095) and 1024 internal relays (B0000-B1023) in the Workstation.. 1.1 Request Message Format Request message is a command message to be sent from the computer to the Workstation. The data structure of request message is shown below. Note that numbers are always in hexadecimal form and converted into ASCII characters. For example, Workstation unit number 14 will appear in the message as character 0(30h) followed by character E(45h); a BCC of 5Ah will appear in the message as character 5(35h) followed by character A(41h).
上傳時間： 2013-10-28
上傳用戶：cxl274287265
特點 精確度0.1%滿刻度 ±1位數 可量測 交直流電流/交直流電壓/電位計/傳送器/Pt-100/荷重元/電阻 等信號 顯示范圍-1999-9999可任意規劃 具有異常值與異常次數記錄保留功能 異常信號過高或過低或范圍內或范圍外檢測可任意設定 報警繼電器復歸方式可任意設定 尺寸小,穩定性高 2.主要規格 精確度: 0.1% F.S. ±1 digit 0.2% F.S. ±1 digit(AC) 取樣時間: 16 cycles/sec. 顯示值范圍: -1999 - +9999 digit adjustable 啟動延遲動作時間: 0-99.9 second adjustable 繼電器延遲動作時間: 0-99.9 second adjustable 繼電器復歸方式: Manual (N) / latch(L) can be modified 繼電器動作方向: HI /LO/GO/HL can be modified 繼電器容量: AC 250V-5A, DC 30V-7A 過載顯示: "doFL" 溫度系數: 50ppm/℃ (0-50℃) 顯示幕: Red high efficiency LEDs high 14.22mm(.56")(PV) Red high efficiency LEDs high 7.0mm(.276")(NO) 參數設定方式: Touch switches 記憶型式 : Non-volatile E2PROM memory 絕緣耐壓能力: 2KVac/1 min. (input/output/power) 1600Vdc(input/output 使用環境條件 : 0-50℃(20 to 90% RH non-condensed) 存放環境條件: 0-70℃(20 to 90% RH non-condensed) CE認證: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上傳時間： 2013-11-02
上傳用戶：fandeshun
特點 精確度0.05%滿刻度 ±1位數 顯示范圍-19999-99999可任意規劃 可直接量測直流4至20mA電流,無需另接輔助電源 尺寸小(24x48x50mm),穩定性高 分離式端子,配線容易 CE 認證 主要規格 輔助電源: None 精確度: 0.05% F.S. ±1 digit(DC) 輸入抗阻: approx. 250 ohm with 20mA input 輸入電壓降: max. DC5V with 20mA input 最大過載能力: < ±50mA 取樣時間: 2.5 cycles/sec. 顯示值范圍: -19999 - 99999 digit adjustable 歸零調整范圍: -999-999 digit adjustable 最大值調整范圍: -999-999 digit adjustable 過載顯示: " doFL " or "-doFL" 極性顯示: " 一 " for negative readings 顯示幕 : Brigh Red LEDs high 8.6mm(.338") 溫度系數 : 50ppm/℃ (0-50℃) 參數設定方式: Touch switches 記憶型式: Non-volatile E2 外殼材料: ABS 絕緣耐壓能力: 2KVac/1 min. (input/case) 使用環境條件: 0-50℃(20 to 90% RH non-condensed) 存放環境條件: 0-70℃(20 to 90% RH non-condensed) 外型尺寸: 24x48x50mm CE認證: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上傳時間： 2013-10-09
上傳用戶：lhuqi
This application note covers the design considerations of a system using the performance features of the LogiCORE™ IP Advanced eXtensible Interface (AXI) Interconnect core. The design focuses on high system throughput through the AXI Interconnect core with F MAX and area optimizations in certain portions of the design. The design uses five AXI video direct memory access (VDMA) engines to simultaneously move 10 streams (five transmit video streams and five receive video streams), each in 1920 x 1080p format, 60 Hz refresh rate, and up to 32 data bits per pixel. Each VDMA is driven from a video test pattern generator (TPG) with a video timing controller (VTC) block to set up the necessary video timing signals. Data read by each AXI VDMA is sent to a common on-screen display (OSD) core capable of multiplexing or overlaying multiple video streams to a single output video stream. The output of the OSD core drives the DVI video display interface on the board. Performance monitor blocks are added to capture performance data. All 10 video streams moved by the AXI VDMA blocks are buffered through a shared DDR3 SDRAM memory and are controlled by a MicroBlaze™ processor. The reference system is targeted for the Virtex-6 XC6VLX240TFF1156-1 FPGA on the Xilinx® ML605 Rev D evaluation board
上傳時間： 2013-11-23
上傳用戶：shen_dafa
