The PW4556 series of devices are highly integrated Li-Ion and Li-Pol linear chargers targetedat small capacity battery for portable applications. It is a complete constant-current/ constantvoltage linear charger. No external sense resistor is needed, and no blocking diode is required dueto the internal MOSFET architecture. It can deliver up to 300mA of charge current (using a goodthermal PCB layout) with a final float voltage accuracy of ±1%. The charge voltage is fixed at 4.2V or4.35V, and the charge current can be programmed externally with a single resistor. The chargerfunction has high accuracy current and voltage regulation loops and charge termination
The PW4554 is a cost-effective, fully integrated high input voltage single-cell Li-ion battery charger.The charger uses a CC/CV charge profile required by Li-ion battery. The charger accepts an inputvoltage up to 24V but is disabled when the input voltage exceeds the OVP threshold, typically 6.8V,to prevent excessive power dissipation. The 24V rating eliminates the over-voltage protection circuitrequired in a low input voltage charger
PW4203 is a 4.5-22V input, 2A multi-cell synchronous Buck Li-Ion battery charger, suitable forportable application. Select pin is convenient for multi-cell charging. 800 kHz synchronous buckregulator integrates of 22V rating FETs with ultra low on- resistance to achieve high efficiency andsimple circuit design.The PW4203 is available in an 8-pin SOP package, provides a very compact system solution andgood thermal conductance
The PW3130 series product is a high integration solution for lithium-lion/polymer batteryprotection.PW3130 contains advanced power MOSFET, high-accuracy voltage detection circuits anddelay circuits. PW3130 is put into an ultra-small SOT23-5 package and only one external componentmakes it an ideal solution in limited space of battery pack. PW3130 has all the protection functionsrequired in the battery application including overcharging, overdischarging, overcurrent and loadshort circuiting protection etc. The accurate overcharging detection voltage ensures safe and fullutilization charging.The low standby current drains little current from the cell while in storage. Thedevice is not only targeted for digital cellular phones, but also for any other Li-Ion and Li-Polybattery-powered information appliances requiring long-term battery life
The PW2601 is a charger front-end integrated circuit designed to provide protection to Li-ionbatteries from failures of charging circuitry. The device monitors the input voltage, battery voltageand the charging current to make sure all three parameters are operated in normal range. Thedevice will switch off internal MOSFET to disconnect IN to OUT to protect load when any of inputvoltage, output current exceeds the threshold. The Over temperature protection (OTP) functionmonitors chip temperature to protect the device. The PW2601 also can protect the system’sbattery from being over charged by monitors the battery voltage continuously. The deviceoperates like a linear regulator, maintaining a 5.1V output with input voltages up to the input overvoltage threshold.The PW2601 is available in DFN-2x2-8L package. Standard products are Pb-free and Halogenfree
The PW2053 is a high-efficiency monolithic synchronous buck regulator using a constantfrequency, current mode architecture. The device is available in an adjustable version. Supply currentwith no load is 40uA and drops to <1uA in shutdown. The 2.5V to 5.5V input voltage range makesthe PW2053 ideally suited for single Li-Ion battery powered applications. 100% duty cycle provideslow dropout operation, extending battery life in portable systems. PWM/PFM mode operationprovides very low output ripple voltage for noise sensitive applications. Switching frequency isinternally set at 1.2MHz, allowing the use of small surface mount inductors and capacitors. Lowoutput voltages are easily supported with the 0.6V feedback reference voltage
基于LabVIEW2012FPGA模式的數據采集和存儲系統摘 要:為了提高數據采集系統精度,減少開發成本,提高開發效率,基于LabVIEW虛擬儀器開發工具研究并設計了一
種數據采集系統。該系統采用FPGA編程模式和網絡流技術實現大批量數據實時傳輸,并對數據進行分析處理和存儲。系
統硬件采用美國NI實時控制器CRIO?9025,實現16路數據可靠采集與存儲。實驗仿真及實際運行結果表明該數據采集系
統能夠精確地對數據進行實時采集以及分析處理,達到了項目要求。
關鍵詞:FPGA;FIFO;網絡流;數據采集系統;SQL數據庫
中圖分類號:TN98?34 文獻標識碼:A 文章編號:1004?373X(2014)14?0142?04
Data acquisition and storage system based on LabVIEW 2012FPGA pattern
WANG Shu?dong1,2
,WEI Kong?zhen1
,LI Xiao?pei1
(1. College of Electrical and Information Engineering,Lanzhou University of Technology,Lanzhou 730050,China;
2. Gansu Key Laboratory for Advanced Industrial Process Control,Lanzhou 730050,China)