AVR的UCO/s-ii，在ICC AVR環境編譯可直接運行
上傳時間： 2013-12-24
上傳用戶：qb1993225
此源代碼為UC/Os-ii移植到51單片機的源代碼.包括OS_CPU.H,OS_CPU_C.C,OS_CPU_A.S三個主要文件
標簽： OS_CPU_C OS_CPU_A OS_CPU Os-ii
上傳時間： 2015-04-19
上傳用戶：王楚楚
ARM7在uC/Os-ii下的測試代碼 含: define.s main.c Display.c LED.c os_dbg.c Uart.c includes.h ML674000.h os_cfg.h
標簽： includes Display 674000 define
上傳時間： 2016-06-05
上傳用戶：Yukiseop
Altera s IIC code,Quarts II complier
標簽： complier Altera Quarts code
上傳時間： 2016-10-02
上傳用戶：ls530720646
Nios II Software Developer’s Handbook
標簽： Developer Handbook Software Nios
上傳時間： 2014-01-25
上傳用戶：lnnn30
This tutorial presents an introduction to Altera’s Nios R II processor, which is a soft processor that can be in- stantiated on an Altera FPGA device. It describes the basic architecture of Nios II and its instruction set. The NiosII processor and its associated memory and peripheral components are easily instantiated by using Altera’s SOPCBuilder in conjuction with the Quartus R II software.
標簽： processor introduction tutorial presents
上傳時間： 2014-12-08
上傳用戶：星仔
Nios II定制指令用戶指南：With the Altera Nios II embedded processor, you as the system designer can accelerate time-critical software algorithms by adding custom instructions to the Nios II processor instruction set. Using custom instructions, you can reduce a complex sequence of standard instructions to a single instruction implemented in hardware. You can use this feature for a variety of applications, for example, to optimize software inner loops for digital signal processing (DSP), packet header processing, and computation-intensive applications. The Nios II configuration wizard,part of the Quartus® II software’s SOPC Builder, provides a graphical user interface (GUI) used to add up to 256 custom instructions to the Nios II processor. The custom instruction logic connects directly to the Nios II arithmetic logic unit (ALU) as shown in Figure 1–1.
上傳時間： 2013-10-12
上傳用戶：kang1923
UcOs ii的多任務操作系統全部原代碼 包含這些cpu的原代碼： 8051 68H11 8088 AVR XA 196 TI DSP 54XX ARM C167 68H12 68000 SH3
上傳時間： 2015-05-14
上傳用戶：ruan2570406
關于 uC/Os-ii 在 LPC210X 上移植的說明 1. 全部代碼在 ADS1.2 中編譯調試. 2. 您可以更改 RO BASE 為 0x0000 0000, 這樣可以將代碼寫入 flash 中運行. 5. 全部代碼采用 ARM 指令. 6. uC/Os-ii 版本為 V2.52. 7. 當您暫停程序的時候, 如果定時器開著, 那么定時器并不會暫停,需要注意 8. Vectors.S 文件中的 startup 段為程序入口. 9. 編譯時下面的警告不必理會. Warning : C2871W: static OS_InitTaskStat declared but not used OS_CORE.C line 1108 10. 如果您想通過軟件仿真,請將 PLL.C 中的第 51 行屏蔽, 怎樣就可以看到任務逐個切換,最后將進入空閑任務. 11. 此次移植將許多 uC/Os-ii 的功能函數都關閉了,請查看 OS_CFG.H 文件.
上傳時間： 2013-12-25
上傳用戶：Divine
UCOS/II for ICCAVR - The version of UCOS/II is 2.04 - the original port was done by Ole Saether for the IAR compiler. Jens E. Holtegaard ported one version using ICCAVR. Joerg Meyer did another port (using Jens port as a start?). This is basically Joerg s port plus a little bit of changes and documentation by me. - YOU MUST DOWNLOAD THE MAIN PART OF THE UCOS/II FROM THE UCOS/II WEBSITE http://www.ucos-ii.com . The supplied project file assumes the portable source is in the ..\source directory. - Joerg has written couple document showing the stack frames etc. but it is in German :-) They are included in this directory. - The Timer2 overflow interrupt is used for Timer Tick. If you want to change that, modify os_cpu_c.c and os_cpu_a.s - I have tested this using ATMega103 with and without external RAM using AVR Studio simulator. See test1.c test program. Both Code Compressed (PRO) and STD versions have been tested.
標簽： UCOS original Saether version
上傳時間： 2015-11-14
上傳用戶：ippler8
