介紹了一種基于C8051F020單片機的多路壓力測量儀。該測量儀選用電阻應變式壓力傳感器采集壓力信號，并經放大電路處理后送入C8051F020單片機，再由C8051F020單片機內部的A/D轉換器將采集到的壓力信號進行模數轉化，然后分別對數據進行存儲和顯示。該測量儀能測量6路壓力信號，并且各測量點都能單獨檢測和設置。由于采用了C8051F020單片機，簡化了硬件電路，增強了抗干擾能力，使得測量儀具有測量精度高，沖擊小等特點。 Abstract: A measurement apparatus for multi-channel pressure based on single chip microcomputer is introduced.It can measure 6 channels signal of the pressure，and the pressure measure points can be detection and located individually.The pressure signal sampling is obtained by resistor stress-type pressure sensors，the digital signals of 6 channels are collected through amplifying and adjustment circuit of pressure signals and internal integrated A/D converter of MCU.Finally，and it realizes the function to store and display data separately.C8051F020 was used to made hardware circuit simple，and it also enhanced the anti-interference ability.It features high precision and little impact.
上傳時間： 2013-11-16
上傳用戶：yare
介紹一種采用單片機技術和基站器件EM4095的手持式低頻RFID讀卡器方案。首先對整個系統框架進行說明，然后介紹主要功能模塊的設計，給出了各模塊的原理圖。重點描述了基站器件EM4095的性能參數和功能原理，最后描述了該系統的主程序流程圖。 Abstract: In this paper,a handheld RFID reader based on MCU and EM4095 is introduced.At first，the configuration of this system is explained.Then the design of main modules and schematic documents are particularly presented.The parameters and principle of the chip EM4095 are introduced in detail. At last，the main software flow is given
上傳時間： 2013-10-18
上傳用戶：windypsm
MMC/SD卡以其優越的性能，在單片機嵌入式設備中得到廣泛應用。將MMC/SD卡作為外部掉電存儲介質應用于音頻信號發生器中，通過8051F330單片機上的SPI接口，實現單片機—MMC/SD卡的存儲擴展，設計了此硬件平臺上的MMC/SD卡的單片機驅動程序，并給出了相應的程序代碼，滿足音頻信號發生器的大容量存儲要求。 Abstract: MMC/SD card is more and more widely used in the single chip embedded devices for their excellent performances.This article introduces the application of MMC/SD card as the external power down storage medium in audio signal generator. The extension technology especially for storage of single chip-MMC/SD card via SPI interfaces in 8051F330 single chip, including designs single chip drive program of MMC/SD card based on hardware platform,and also gives the key coding of the program. The implementation of big capacity storage is meaningful in audio signal generator.
上傳時間： 2014-12-27
上傳用戶：黃華強
針對眾多低成本數據采集需求，采用帶有片上USB控制器和D/A轉換器的混合信號微處理器C8051F340，設計了一款可通過USB接口和LabVIEW圖形用戶界面實現與PC機聯機的數據采集器，同時借助系統的SD卡存儲獨立實現現場長時間采集數據。該數據采集器成本低，結構簡單，體積小，已成功用于工業現場。 Abstract: Aiming at the need of low cost data acquisition, a data acquisition device is designed based on C8051F340 which is a mixed-signal microcontroller and integrates USB controller and A/D controller on a chip.The data acquisition device which can combine with PC by USB interface and LabVIEW graphical user interface,can realize data acquisition. At the same time,it can be solely run a long time in virtue of SD card in field.The date aequisition device features low cost,simple structure and little sharp, and it has been used in industry field.
標簽： C8051F340 數據 集器設計
上傳時間： 2014-05-31
上傳用戶：1109003457
為了解決磁放大器性能測試過程中，需要對其供給不同數值恒定電流的問題，設計了一種基于DAC7512和單片機的數控恒流源系統。該系統采用AT89C51作為主控器件，將計算機發送的電流控制字命令轉換為D/A轉換器控制字，通過模擬SPI通信接口，寫D/A控制字到DAC7512，從而控制其輸出相應數字電壓值，經差動縮放電路、電壓/電路變換電路和功率驅動電路，最后輸出恒定電流。實驗結果表明，恒流源輸出電流調節范圍為-45~+45 mA、精度為±0.1 mA，分辨率達0.024 4 mA，具有應用靈活，外圍電路簡單，可靠性高的特點。該數控直流恒流源也可為相關產品的測試系統研發提供參考。 Abstract: In order to solve the need to supply different values constant current for the magnetic amplifier in testing process， numerical control constant current source system was designed based on DAC7512 chip and microcontroller technology. The system used the AT89C51 as the main chip， which can convert the current control word from computer into to D/A control words. And the system wrote D/A control word into the DAC7512 chip to control the output voltage value by the SPI communication interface， which can output corresponding constant current figures by scaling circuit， the V/I converter and power drive circuit. Experimental results show that the current source output current adjustment range is -45~+45mA， accuracy is ± 0.1mA， and resolution ratio is 0.024 4mA
上傳時間： 2014-12-27
上傳用戶：invtnewer
提出了一種基于C8051F320的列車安全巡檢儀的設計方案，詳細闡述了巡檢儀的各個模塊的硬、軟件設計。巡檢儀集信息采集、軸溫檢測、照明和記錄存儲等功能于一體，實現了對列車安全巡檢工作有效的監督和科學管理。系統軟件采用C51編寫，對單片機進行有效的電源管理，保證了巡檢儀的穩定性、可靠性和低功耗性。 Abstract: This paper puts forward a design of train safety inspection based on C8051F320,describes all modules hardware and software design of inspection instrument.The inspection instrument has the function of information collection, axle’s temperature detection, lighting and records storage.It can supervise and administer train safety inspection work effectively.The system software using C51 can manage the power of single chip microcomputer, and guarantee the stability, reliability and low power consumption of the inspection instrument.
上傳時間： 2013-12-22
上傳用戶：落花無痕
以AVR單片機ATmega8和USB接口器件PDIUSBD12為核心，基于標準的USB1.1協議，設計一種通用USB接口模塊，以滿足嵌入式系統中對USB接口的需求。對模塊的硬件電路或單片機固件程序的硬件接口層稍加修改即可用于其他各種微處理器。該模塊可為各種嵌入式系統增加USB接口,實現與USB主機系統通信。 Abstract: Based on AVR microcontroller ATmega8 and USB interface chip PDIUSBD12, a general USB interface module is designed according to USB1.1 protocol for various requirements of embedded systems. Only with few modifications in circuit or hardware abstract layer of firmware, the module can be used on many types of microprocessors. All kinds of embedded systems can realize high speed and stable communication with USB host systems, owing to the facility of this module.
上傳時間： 2014-01-08
上傳用戶：趙云興
針對材料試驗機等設備中要求測量或控制材料拉伸或壓縮的位移，一般采用光電軸角編碼器檢測位置信號，輸出正交編碼脈沖信號。若采用其他方法檢測位置信號，必然導致電路設計復雜，可靠性降低。因此，提出一種基于LS7266R1的電子式萬能材料試驗機設計方案。給出了試驗機中的控制器工作原理，LS7266R1與單片機的接口硬件設計，以及主程序軟件流程圖。巧妙地把力量傳感器，位移傳感器等機械運動狀態的壓力或拉力以及位置坐標，變成了電壓信號和電脈沖數字信號，供A/D測量和LS7266R1計數，從而實現了獨立完成材料試驗控制或通過PC機串口命令完成材料試驗控制。 Abstract: Aiming at the requirement that the displacement of the tension and compression always be tested and controlled in the equipement such as material testing machine. The position signal was tested by photoelectric axial angle coder. Therefore， the paper proposes the design of electronic universal testing machine design based on LS7266R1. If the position signal detected by other methods， will inevitably lead to the circuit design complexity， reliability decreased. The work theory of the controller， the hardware interface design between LS7266R1 and single chip， and the flow chart of main program， are presented in this paper. The signal of the compression or tension power and displacement at working， which tested by power sensor and displacement sensor especially， is changed into electric voltage and electric pulse numerical signals. And these signals can be tested by A/D and counted by LS7266R1. Finally the test of the material properties can be controlled by itself， or controlled by the COM command of PC.
上傳時間： 2013-11-02
上傳用戶：yl1140vista
主要介紹了以PIC18F2480單片機為處理器，基于可編程多路開關檢測接口器件MC33993實現的車用多路開關檢測接口電路的設計。該設計克服了以往基于分立元件的檢測接口電路的弊端，簡化了接口電路設計，保證了車用開關工作的可靠性和安全性。 Abstract: The design of automotive multiple switch detection interface circuit based on MC33993 is introduced mainly which adopts PIC18F2480 single chip microprocessor.This circuit overcomes shortage of traditional design which contains many schism elements, and the application of MC33993 also predigests the whole design of interface circuit and guarantees the dependability and security of the switch.
標簽： 33993 MC 多路開關 檢測
上傳時間： 2013-11-19
上傳用戶：star_in_rain
介紹了基于單片機航空交流電參數測試儀的系統設計。以Silicon Labs公司的C8051F005單片機為核心設計出數據采集板，通過RS-232串口與上位機通訊。運用Lab Windows/CVI編寫的上位機軟件實現信號的檢測以及波形和數據的顯示，給出了測試儀硬件電路的組成和軟件流程圖。本系統具有硬件結構簡單、容易實現和成本低等特點，在實際應用中其穩定性、精確性均能滿足客戶要求。 Abstract: The design of aeronautics AC parameters tester based on the single-chip is introduced.The core component of data acquisition board is C8051F005 single chip of Silicon Labs Company,and communication with PC through RS-232. The signal processing software programmed with LabWindows/CVI can be used successfully to fulfill inspection of signal and display of the waveform and data. The hardware and software configuration of test instrument are provided.The hardware of the system is simple, and can be easily realized.The stability and precision of the measurement instrument are enough to meet the requirements.
標簽： C8051F005 單片機 儀的設計 參數測試
上傳時間： 2013-11-18
上傳用戶：wang5829
蟲蟲下載站版權所有 京ICP備2021023401號-1
