The LTC®4099 high effi ciency USB power manager andLi-Ion/Polymer battery charger seamlessly managespower distribution from multiple sources in portableapplications. It is differentiated from other USB powermanagers by its bidirectional I2C port that allows the hostmicroprocessor to control and monitor all aspects of theUSB power management and battery charging processes.In addition, a programmable interrupt generation functionalerts the host microprocessor to changes in device statusand provides unprecedented control of power managementfunctions. This high degree of confi gurability allowspost-layout changes in operation, even changes in thefi eld, and it allows a single qualifi ed device to be usedin a variety of products, thus reducing design time andeasing inventory management.
上傳時間： 2013-10-22
上傳用戶：18602424091
An essential component of a noise-free audio device isa clean power supply, but few switching regulators canoperate at high efficiency while keeping the switchingfrequency out of the audio band. The LTC®3620 fills thisvoid. It is a high efficiency 15mA buck regulator with aprogrammable minimum switching frequency, making itpossible to virtually eliminate audible switching noise. Theinternal synchronous switches and low quiescent currentof this buck regulator provide the ability to maintain highefficiency, while its small footprint makes it ideal for tiny,low power audio applications.
上傳時間： 2013-10-21
上傳用戶：非衣2016
Telecommunication, satellite links and set-top boxes allrequire tuning a high frequency oscillator. The actualtuning element is a varactor diode, a 2-terminal device thatchanges capacitance as a function of reverse bias voltage.1 The oscillator is part of a frequency synthesizingloop, as detailed in Figure 1. A phase locked loop (PLL)compares a divided down representation of the oscillatorwith a frequency reference. The PLL’s output is levelshifted to provide the high voltage necessary to bias thevaractor, which closes a feedback loop by voltage tuningthe oscillator. This loop forces the voltage controlledoscillator (VCO) to operate at a frequency determined bythe frequency reference and the divider’s division ratio.
上傳時間： 2013-12-20
上傳用戶：ABCDE
The LTM4601 DC/DC μModule regulator is a completehigh power density stepdown regulator for up to 12Acontinuous (14A peak) loads. The device is housed ina small 15mm ¥ 15mm ¥ 2.8mm LGA surface mountpackage, thus the large power dissipation is a challengein some applications. This thermal application note willprovide guidelines for using the μModule regulator inambient environments with or without air fl ow. Loadcurrent derating curves are provided for several inputvoltages and output voltages versus ambient temperatureand air fl ow.
上傳時間： 2013-10-19
上傳用戶：bakdesec
Switching regulators are of universal interest. LinearTechnology has made a major effort to address this topic.A catalog of circuits has been compiled so that a designengineer can swiftly determine which converter type isbest. This catalog serves as a visual index to be browsedthrough for a specific or general interest.
標簽： Collection Switching Regulator Circuit
上傳時間： 2013-11-09
上傳用戶：mh_zhaohy
The LTM4600 DC/DC μModule regulator is a complete highpower density stepdown regulator for 10A continuous (14Apeak) loads. The device has two voltage options: 20VINmaximum for the LTM4600EV and 28VIN maximum for theLTM4600HVEV each housed in a small 15mm ¥ 15mm ¥2.8mm LGA surface mount package.
上傳時間： 2013-10-10
上傳用戶：adada
Permission to make digital or hard copies of all or part of this work forpersonal or classroom use is granted without fee provided that copies arenot made or distributed for profit or commercial advantage and that copiesbear this notice and the full citation on the first page. To copy otherwise, torepublish, to post on servers or to redistribute to lists, requires prior specificpermission.
標簽： 數字電源
上傳時間： 2013-10-16
上傳用戶：dddddd
單相橋式逆變電路為例：S1～S4是橋式電路的4個臂，由電力電子器件及輔助電路組成。S1、S4閉合，S2、S3斷開時，負載電壓uo為正S1；S1、S4斷開，S2、S3閉合時，uo為負，把直流電變成了交流電。改變兩組開關切換頻率，可改變輸出交流電頻率。圖5-1 逆變電路及其波形舉例電阻負載時，負載電流io和uo的波形相同，相位也相同。阻感負載時，io滯后于uo，波形也不同（圖5-1b）。t1前：S1、S4通，uo和io均為正。t1時刻斷開S1、S4，合上S2、S3，uo變負，但io不能立刻反向。io從電源負極流出，經S2、負載和S3流回正極，負載電感能量向電源反饋，io逐漸減小，t2時刻降為零，之后io才反向并增大 （2）換流方式分類換流——電流從一個支路向另一個支路轉移的過程，也稱換相。開通：適當的門極驅動信號就可使其開通。關斷：全控型器件可通過門極關斷。半控型器件晶閘管，必須利用外部條件才能關斷，一般在晶閘管電流過零后施加一定時間反壓，才能關斷。研究換流方式主要是研究如何使器件關斷。本章換流及換流方式問題最為全面集中，因此在本章講述1、器件換流利用全控型器件的自關斷能力進行換流（Device Commutation）。2、電網換流由電網提供換流電壓稱為電網換流（Line Commutation）。可控整流電路、交流調壓電路和采用相控方式的交交變頻電路，不需器件具有門極可關斷能力，也不需要為換流附加元件。3、負載換流由負載提供換流電壓稱為負載換流（Load Commutation）。負載電流相位超前于負載電壓的場合，都可實現負載換流。負載為電容性負載時，負載為同步電動機時，可實現負載換流。
上傳時間： 2013-10-15
上傳用戶：qingdou
msp430單片機
標簽： Erratasheet 14x x14 Device
上傳時間： 2013-10-19
上傳用戶：dick_sh
數字控制的交流調速系統所選用的微處理器、功率器件及產生PWM波的方法是影響交流調速系統性能好壞的直接因素。在介紹了正弦脈寬調制(SPWM)技術的基礎上，設計了一種以8098單片機作為控制器，以智能功率模塊IPM為開關器件的變頻調速系統。通過軟件編程，產生正弦脈沖寬度調制波形來控制絕緣柵雙極晶體管的導通和關斷，從而達到控制異步電動機轉速的目的。實驗結果表明，該系統可調頻率調電壓，穩定度高，調速范圍寬，具有較強的實用價值 Abstract: AC variable speed with digital control systems used microprocessors， power devices and generate PWM wave is the direct factors of affecting the performance AC speed regulation system. On the basis of introducing the sinusoidal pulse width modulation (SPWM) technology，this paper designed variable speed system which used 8098 as a controller， intelligent power module IPM as switching device. Through software programming， resulting in sinusoidal pulse width modulation waveform to control the insulated gate bipolar transistor turn on and off， so as to achieve the purpose of speed control of induction motors. Experimental results show that the system can adjust frequency modulation voltage， high stability， wide speed range， has a strong practical value.
上傳時間： 2013-11-14
上傳用戶：ynwbosss
