普通查表原理 查表時，執行CALL指令后，下一條指令的地址被自動壓入堆棧中，然后跳轉到數據表處，執行TJMP指令，PC指針跳轉到PC11~PC8,TBR（TABLE branch REGISTER）,AC(累加器)所指向的地址，該地址的數據通過RTNW指令返回，其中，高4位數據保存到TBR寄存器中，低4位數據保存到累加器AC中。返回時PC指針會自動被堆棧中保存的PC數據覆蓋。
上傳時間： 2014-12-27
上傳用戶：zhaoman32
這是最難的一個程序了，算法是運籌學里的branch band的集裝箱問題的最優動態規劃解法，當年我的頭都大了才實現的，絕得數學加實踐的程序
標簽： 程序
上傳時間： 2015-04-22
上傳用戶：731140412
物流分析工具包。Facility location: Continuous minisum facility location, alternate location-allocation (ALA) procedure, discrete uncapacitated facility location Vehicle routing: VRP, VRP with time windows, traveling salesman problem (TSP) Networks: Shortest path, min cost network flow, minimum spanning tree problems Geocoding: U.S. city or ZIP code to longitude and latitude, longitude and latitude to nearest city, Mercator projection plotting Layout: Steepest descent pairwise interchange (SDPI) heuristic for QAP Material handling: Equipment selection General purpose: Linear programming using the revised simplex method, mixed-integer linear programming (MILP) branch and bound procedure Data: U.S. cities with populations of at least 10,000, U.S. highway network (Oak Ridge National Highway Network), U.S. 3- and 5-digit ZIP codes
標簽： location location-allocation Continuous alternate
上傳時間： 2015-05-17
上傳用戶：kikye
A new cable fault location method based on wavelet reconstruction is proposed. In this method the difference between the currents of faulty phase and sound phase under the high voltage pulse excitation is used as the measured signal and is decomposed in multi-scale by wavelet transform, then reconstructed in single scale. Comparing with traditional fault location method by travelling wave, the presented method will not be interfered by the reflected wave from the branch joint of cables or from other positions where the impedances are not matched and not be influenced by fault types, otherwise, the reflected waves can be recognized even the faulty position is near to the measuring terminal, at the same time, the influence of the wave speed uncertainty can be reduced. The correctness of the proposed method is proved by simulation results.
標簽： method reconstruction location proposed
上傳時間： 2016-02-04
上傳用戶：maizezhen
在模式識別應用中，用分支定界法(branch-and-board method)進行特征的選擇。該程序在matlab環境下實現了該算法，以從六個特征中選擇兩個最佳特征為例
標簽： 模式識別
上傳時間： 2014-01-09
上傳用戶：nanshan
Two 2D phase unwrapping approaches are included: 1. Phase quality guided path following method. 2. Goldstein's branch cut method. The algorithms are described in: D. C. Ghiglia and M. D. Pritt, Two-Dimensional Phase Unwrapping: Theory, Algorithms and Software. New York: Wiley-Interscience, 1998.
標簽： Unwrapping Phase 2D
上傳時間： 2016-04-30
上傳用戶：seanjsj
Regardless of the branch of science or engineering, theoreticians have always been enamored with the notion of expressing their results in the form of closed-form expressions. Quite often, the elegance of the closed-form solution is overshadowed by the complexity of its form and the difficulty in evaluating it numerically. In such instances, one becomes motivated to search instead for a solution that is simple in form and simple to evaluate.
標簽： Communication Channels Digital Fading over 1st
上傳時間： 2020-05-27
上傳用戶：shancjb
Regardless of the branch of science or engineering, theoreticians have always been enamored with the notion of expressing their results in the form of closed-form expressions. Quite often the elegance of the closed-form solution is overshadowed by the complexity of its form and the difficulty in evaluating it numerically. In such instances, one becomes motivated to search instead for a solution that is simple in form and likewise simple to evaluate.
標簽： Communication Channels Digital Fading over 2nd
上傳時間： 2020-05-27
上傳用戶：shancjb
Agilent 34401A Service Guide.pdfIEC Measurement Category II includes electrical devices connected to mains at an outlet on a branch circuit. Such devices include most small appliances, test equipment, and other devices that plug into a branch outlet or socket. The 34401A may be used to make measurements with the HI and LO inputs connected to mains in such devices, or to the branch outlet itself (up to 300 VAC). However, the 34401A may not be used with its HI and LO inputs connected to mains in permanently installed electrical devices such as the main circuit-breaker panel, sub-panel disconnect boxes, or permanently wired motors. Such devices and circuits are subject to overvoltages that may exceed the protection limits of the 34401A. Note: Voltages above 300 VAC may be measured only in circuits that are isolated from mains. However, transient overvoltages are also present on circuits that are isolated from mains. The Agilent 34401A are designed to safely withstand occasional transient overvoltages up to 2500 Vpk. Do not use this equipment to measure circuits where transient overvoltages could exceed this level. Additional Notices Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC This product complies with the WEEE Directive (2002/96/EC) marking requirement. The affixed product label (see below) indicates that you must not discard this electrical/electronic product in domestic household waste. Product Category: With reference to the equipment types in the WEEE directive Annex 1, this product is classified as a "Monitoring and Control instrumentation" product. Do not dispose in domestic household waste. To return unwanted products, contact your local Agilent office, or see www.agilent.com/environment/product for more information. Agilent 34138A Test Lead Set The Agilent 34401A is compatible with the Agilent 34138A Test Lead Set described below. Test Lead Ratings Test Leads - 1000V, 15A Fine Tip Probe Attachments - 300V, 3A Mini Grabber Attachment - 300V, 3A SMT Grabber Attachments - 300V, 3A Operation The Fine Tip, Mini Grabber, and SMT Grabber attachments plug onto the probe end of the Test Leads. Maintenance If any portion of the Test Lead Set is worn or damaged, do not use. Replace with a new Agilent 3413
標簽： agilent
上傳時間： 2022-02-20
上傳用戶：
