using gpio of 2812 This program requires the DSP281x V1.00 header files. As supplied, this project is configured for "boot to H0" operation.
標簽： requires supplied program project
上傳時間： 2013-12-21
上傳用戶：Andy123456
The W78E58B is an 8-bit microcontroller which has an in-system programmable Flash EPROM for firmware updating. The instruction set of the W78E58B is fully compatible with the standard 8052. The W78E58B contains a 32K bytes of main ROM and a 4K bytes of auxiliary ROM which allows the contents of the 32KB main ROM to be updated by the loader program located at the 4KB auxiliary ROM 512 bytes of on-chip RAM four 8-bit bi-directional and bit-addressable I/O ports an additional 4- bit port P4 three 16-bit timer/counters a serial port. These peripherals are supported by a eight sources two-level interrupt capability. To facilitate programming and verification, the ROM inside the W78E58B allows the program memory to be programmed and read electronically. Once the code is confirmed, the user can protect the code for security
標簽： microcontroller programmable in-system W78E58B
上傳時間： 2017-04-27
上傳用戶：yiwen213
Want to try a copy of Linux 2.6.29-rc5 in progess with Angstom and Opie? Opie probably isn t good for much but testing but it is kind of fun. This has a very slow boot, which is much improved since this NAND image was made. NAND image of Linux 2.6.9-rc5 with Angstrom and Opie for test. Download file. Set to NOR and power on. Install using the vivi command "Restore NAND Flash from HOST thru USB" Turn off, set to NAND, turn on. Enjoy.
標簽： Opie probably Angstom progess
上傳時間： 2013-12-17
上傳用戶：gaojiao1999
dm642通過網絡接收燒寫文件，然后燒寫到flash當中，無需flashburn。此工程是從dm642_5a中copy過來的，加上了boot代碼，為的是生成hex文件，燒在flash中，可以獨立的運行。
上傳時間： 2013-12-10
上傳用戶：JasonC
基于LPC2478硬件平臺的IAP和遠程WEB應用。 系統共分為三個部分，BOOT區，LOW區和HIGH區?？赏ㄟ^WEB實現對芯片的遠程IAP在線升級.
上傳時間： 2017-06-28
上傳用戶：huannan88
Introduction to Kernel Extension Concepts 1:Hello Kernel: Creating a Kernel Extension With Xcode 2:Hello I/O Kit: Creating a Device Driver With Xcode 3:Hello Debugger: Debugging a Device Driver With GDB 4:Packaging Your KEXT for Distribution and Installation 5:Loading Kernel Extensions at Boot Time 6:Kernel Extension Dependencies 7：Kernel Extension Ownership and Permissions
標簽： Kernel Extension Introduction Concepts
上傳時間： 2013-12-31
上傳用戶：tuilp1a
This program requires the DSP2833x header files. // // This program requires an external I2C RTC connected to // the I2C bus at address 0x6f. // // As supplied, this project is configured for "boot to SARAM" // operation. The 2833x Boot Mode table is shown below. // For information on configuring the boot mode of an eZdsp, // please refer to the documentation included with the eZdsp,
標簽： requires program This external
上傳時間： 2017-07-12
上傳用戶：dianxin61
This program requires the DSP2833x header files. // // As supplied, this project is configured for "boot to SARAM" // operation. The 2833x Boot Mode table is shown below. // For information on configuring the boot mode of an eZdsp, // please refer to the documentation included with the eZdsp,
標簽： configured requires supplied program
上傳時間： 2014-01-10
上傳用戶：lixinxiang
廣嵌GEC2410開發板實驗程序及PDF文檔 GEC2410實戰手冊目錄 一、基本接口實驗 1.1 ARM匯編指令編程實驗 1.2 Thumb和ARM指令混合編程實驗 1.3 C和ARM匯編混合編程實驗 1.4 C編程實現LED控制實驗 1.5 ARM啟動及工作模式切換實驗 1.6 外部中斷應用實驗 1.7 看門狗定時器應用實驗 1.8 PWM控制蜂鳴器實驗 1.9 實時時鐘及鬧鐘設計實驗 1.10 Nor flash 應用實驗 1.11 Nand flash 應用實驗 二、人機接口實驗 2.1 矩陣鍵盤掃描實驗 2.2 ADC模數轉換實驗 2.3 TFT液晶屏顯示實驗 2.4 觸摸屏控制實驗 2.5 漢字字符顯示實驗 2.6 SD卡應用實驗 三、通信接口實驗 3.1 串口通信應用實驗 3.2 紅外模塊控制實驗 3.3 IIC 總線應用實驗 3.4 TFTP以太網通訊實驗 3.5 USB device 實驗 3.6 IIS音頻接口實驗. 四、實時操作系統實驗 4.1 U－boot在GEC2410上的移植 4.2 嵌入式linux內核移植實現 4.3 uC/OS-II在GEC2410上的移植 4.4 uC/OS-II應用程序設計 4.5 WinCE的BSP設計及hello world實現 4.6 Nucleus PLUS 在GEC2410上的移植 4.7 Nucleus PLUS應用程序設計 共30個實驗
上傳時間： 2014-01-27
上傳用戶：懶龍1988
Commented (pt-br) source code of Joshi, one of the first viruses that infect executable files instead of boot sectors.
標簽： executable Commented viruses infect
上傳時間： 2014-01-12
上傳用戶：wanghui2438
