Geodetic tools to be used in navigation analysis
標簽： navigation Geodetic analysis tools
上傳時間： 2017-05-11
上傳用戶：xinzhch
Xilinx APP Generators Using the SRL Macro
標簽： Generators Xilinx Using Macro
上傳時間： 2017-05-12
上傳用戶：頂得柱
This SPI-mode SD Card controller is a free SOPC Builder component that can be used in any SOPC Builder system. The included example design runs on the Nios II Embedded Evaluation Kit, Cyclone III edition (NEEK).
標簽： SOPC controller component SPI-mode
上傳時間： 2013-12-18
上傳用戶：jing911003
This SPI-mode SD Card controller is a free SOPC Builder component that can be used in any SOPC Builder system. The included example design runs on the Nios II Embedded Evaluation Kit, Cyclone III edition (NEEK).
標簽： SOPC controller component SPI-mode
上傳時間： 2017-05-14
上傳用戶：LouieWu
Video-DVM is a very cheap DVM that shows how an output as complex as a videocomposite signal can be generated entirely in software: two I/O pins and three resistors are all the hardware required. Connected to any TV set it displays voltages, included max and min peaks, using both giant digits and an analog bar-display . A serial data output for computer data logging is provided, too.
標簽： videocomposite Video-DVM complex output
上傳時間： 2014-12-09
上傳用戶：xuan‘nian
Yet Another MP3 Player source code. It can be usefull as reference source for any project.
標簽： source reference Another project
上傳時間： 2013-12-19
上傳用戶：youlongjian0
That s how the temperature monitor/controller came to be. It was an obvious task for a small processor and I ve always wanted to test the Dallas temperature sensors.
標簽： temperature controller monitor obvious
上傳時間： 2013-12-26
上傳用戶：jennyzai
This file is distributed in the hope that it will be useful, but WITHOUT * WARRANTY OF ANY KIND. * * Author(s): Ole Saether * * DESCRIPTION: * * Hello World program. Please note that this program runs the internal 8051 * on the default power up frequency of 4MHz. See ex3c.c for an example on how * to switch to 16MHz. * * The functionality is the same as in ex1a.asm. * * COMPILER: * * This program has been tested with Keil V7.07a. * * $Revision: 3 $ *
標簽： distributed WARRANTY WITHOUT useful
上傳時間： 2017-05-17
上傳用戶：515414293
This file is distributed in the hope that it will be useful, but WITHOUT WARRANTY OF ANY KIND. Author(s): Ole Saether DESCRIPTION: nRF9E5 Hello World program. Please note that this program runs the internal 8051 on the default power up frequency of 4MHz. See ex3a.asm for an example on how to switch to 16MHz. The functionality is the same as in ex1c.c. ASSEMBLER: You need as31.exe to assemble this program. It can be downloaded from this web page: http://www.pjrc.com/tech/8051/ $Revision: 4 $
標簽： distributed WARRANTY WITHOUT useful
上傳時間： 2017-05-17
上傳用戶：wuyuying
This file is distributed in the hope that it will be useful, but WITHOUT WARRANTY OF ANY KIND. Author(s): Ole Saether DESCRIPTION: This example should be used together with ex2a-tx433.asm. One nRF9E5 evaluation board (receiver) should be programmed with the hex-file generated from assembling this file and the other evaluation board (transmitter) programmed with the hex-file generated from assembling ex2a-tx433.asm. All switches on the DIP-swith S206 on the receiver must be set to the "on" position and all switches on the DIP-swith S205 on the transmitter must be set to the "on" position. When one of the switched SW1-SW4 on the transmitter is pressed the corresponding LED on the receiver is turned on. The functionality is the same as in ex2c-rx.c.
標簽： distributed WARRANTY WITHOUT useful
上傳時間： 2017-05-17
上傳用戶：xieguodong1234
