it is a cleaner for windows msconfig When you disable an msconfig item it will still appear on there. This programme let you remove disabled msconfig items
標簽： msconfig cleaner disable windows
上傳時間： 2013-12-24
上傳用戶：戀天使569
Abstract: Many digital devices incorporate analog circuits. For instance, microprocessors, applicationspecificintegrated circuits (ASICs), and field-programmable gate arrays (FPGAs) may have internalvoltage references, analog-to-digital converters (ADCs) or digital-to-analog converters (DACs). However,there are challenges When you integrate more analog onto a digital design. As with all things in life, inelectronics we must always trade one parameter for another, with the application dictating the propertrade-off of analog function. In this application note, we examine how the demand for economy of spaceand cost pushes analog circuits onto digital substrates, and what design challenges emerge.
上傳時間： 2013-11-17
上傳用戶：菁菁聆聽
Abstract: Most magnetic read head data sheets do not fully specify the frequency-dependent components andare often vague When specifying other key parameters. In some cases, the specifications of two very similarheads from two different manufacturers might be quite different in terms of parameters specified and omitted.The limitations in the data sheets make designing an optimum card reading system unnecessarily difficult andtime consuming. This document outlines a strategy to overcome the above shortcomings and offers guidelinesto overcome the noise issues.
上傳時間： 2013-11-13
上傳用戶：dysyase
Abstract: Perfection is relative and application specific. The perfect race car is not the car we use to commute to work. We need products for everyday use that are high quality, affordable, and solidly reliable. There will be times When we must use components that are not perfect, and this is When calibration becomes important. Calibration techniques reduce tolerances in imperfect manufacturing equipment while maintaining affordability.
標簽： 校準
上傳時間： 2013-10-09
上傳用戶：哈哈hah
Abstract: Using a DAC and a microprocessor supervisor, the system safety can be improved in industrial controllers, programmablelogiccontrollers (PLC), and data-acquisition systems. The analog output is set to zero-scale (or pin-programmable midscale) When amicroprocessor failure, optocoupler failure, or undervoltage condition occurs. A simple application is shown on how to implement thisfunction.
上傳時間： 2013-10-17
上傳用戶：sjb555
Who has never experienced oscillations issues When using an operational amplifier? Opampsare often used in a simple voltage follower configuration. However, this is not the bestconfiguration in terms of capacitive loading and potential risk of oscillations.Capacitive loads have a big impact on the stability of operational amplifier-basedapplications. Several compensation methods exist to stabilize a standard op-amp. Thisapplication note describes the most common ones, which can be used in most cases.The general theory of each compensation method is explained, and based on this, specific
上傳時間： 2013-10-28
上傳用戶：chenbhdt
Highlights the LTC1062 as a lowpass filter in a phase lock loop. Describes how the loop's bandwidth can be increased and the VCO output jitter reduced When the LTC1062 is the loop filter. Compares it with a passive RC loop filter. Also discussed is the use of LTC1062 as simple bandpass and bandstop filter.
上傳時間： 2013-10-24
上傳用戶：chens000
ANALOG INPUT BANDWIDTH is a measure of the frequencyat which the reconstructed output fundamental drops3 dB below its low frequency value for a full scale input. Thetest is performed with fIN equal to 100 kHz plus integer multiplesof fCLK. The input frequency at which the output is −3dB relative to the low frequency input signal is the full powerbandwidth.APERTURE JITTER is the variation in aperture delay fromsample to sample. Aperture jitter shows up as input noise.APERTURE DELAY See Sampling Delay.BOTTOM OFFSET is the difference between the input voltagethat just causes the output code to transition to the firstcode and the negative reference voltage. Bottom Offset isdefined as EOB = VZT–VRB, where VZT is the first code transitioninput voltage and VRB is the lower reference voltage.Note that this is different from the normal Zero Scale Error.CONVERSION LATENCY See PIPELINE DELAY.CONVERSION TIME is the time required for a completemeasurement by an analog-to-digital converter. Since theConversion Time does not include acquisition time, multiplexerset up time, or other elements of a complete conversioncycle, the conversion time may be less than theThroughput Time.DC COMMON-MODE ERROR is a specification which appliesto ADCs with differential inputs. It is the change in theoutput code that occurs When the analog voltages on the twoinputs are changed by an equal amount. It is usually expressed in LSBs.
上傳時間： 2013-11-12
上傳用戶：pans0ul
Finite state machines are widely used in digital circuit designs. Generally, When designing a state machine using an HDL, the synthesis tools will optimize away all states that cannot be reached and generate a highly optimized circuit. Sometimes, however, the optimization is not acceptable. For example, if the circuit powers up in an invalid state, or the circuit is in an extreme working environment and a glitch sends it into an undesired state, the circuit may never get back to its normal operating condition.
標簽： Creating Machines Mentor State
上傳時間： 2013-10-08
上傳用戶：wangzhen1990
Abstract: Using a wafer-level package (WLP) can reduce the overall size and cost of your solution.However When using a WLP IC, the printed circuit board (PCB) layout can become more complex and, ifnot carefully planned, result in an unreliable design. This article presents some PCB designconsiderations and general recommendations for choosing a 0.4mm- or 0.5mm-pitch WLP for yourapplication.
標簽： Considerations Guidelines and Design
上傳時間： 2013-10-14
上傳用戶：ysystc699
