The Original USB 2.0 specification released on April 27, 2000 Errata to the USB 2.0 specification as of December 7, 2000 Mini-B connector Engineering Change Notice to the USB 2.0 specification. Pull-up/pull-down Resistors Engineering Change Notice to the USB 2.0 specification. Errata to the USB 2.0 specification as of May 28, 2002 Interface Association Descriptor Engineering Change Notice to the USB 2.0 specification. Rounded Chamfer Engineering Change Notice to the USB 2.0 specification as of October 8, 2003 Unicode Engineering Change Notice to the USB 2.0 specification as of February 21, 2005 Inter-Chip USB Supplement Revision 1.0 as of March 13, 2006 Revision 1.3 of the USB On-The-Go Supplement as of December 5, 2006 Revision 1.01 of the Micro-USB Cables and Connectors Specification as of April 4, 2007 USB 2.0 Link Power Management Addendum Engineering Change Notice to the USB 2.0 specification as of July 16, 2007.
標簽： specification 2.0 USB Original
上傳時間： 2013-12-31
上傳用戶：familiarsmile
How to use USB without knowing USB
標簽： USB knowing without How
上傳時間： 2014-01-21
上傳用戶：lhc9102
cpress usb 芯片Vender 處理固件。 The purpose of this software is to demonstrate how to implement vendor specific commands. The following vendor specific commands are implemented: A0 Firmware Upload/Download A2 EEProm Load A3 External Ram Load A4 Set I2C Addr A5 Get IIC Type (1 Byte or 2 Byte EEPROM) A6 Get Chip Rev A8 Renumerate
標簽： demonstrate implement software purpose
上傳時間： 2016-01-14
上傳用戶：stvnash
S3C2410的驅動,包括USB UART,需在PB環境編譯
標簽： S3C2410 UART USB 驅動
上傳時間： 2013-12-21
上傳用戶：yyyyyyyyyy
NAND Flash Boot Please select function : 0 : USB download file（通過USB下載文件） 1 : Uart download file（通過串口下載文件） 2 : Write Nand flash with download file（將下載的文件燒寫到NandFlash） 3 : Load Pragram from Nand flash and run（從NandFlash裝載文件并運行） 4 : Erase Nand flash regions（擦除NandFlash區域） 5 : Write NOR flash with download file（將下載的文件燒寫到NorFlash） 6 : Set boot params（設置Linux啟動相關參數） 7 : Set AutoBoot parameter,1:linux 2:wince(設置WINCE自啟動）
標簽： download USB function Please
上傳時間： 2016-02-15
上傳用戶：s363994250
Ti TMS320C6713 DSK的測試程序,全部代碼都有.包括BOOT,CODEC,EDMA,EEPROM,FLASH,GPIO,SDRAM,Timer,UART,USB等
標簽： EEPROM C6713 CODEC FLASH
上傳時間： 2014-09-10
上傳用戶：851197153
verilog code which receive from uart RX and then output to lcd text display.
標簽： verilog receive display output
上傳時間： 2016-03-07
上傳用戶：songrui
// This program demonstrates how to configure the C8051F060 to write to and read // from the UART interface. The program reads a word using the UART0 interrupts // and outputs that word to the screen, with all characters in uppercase
標簽： demonstrates C8051F060 configure the
上傳時間： 2013-12-23
上傳用戶：hopy
學習usb的必讀書籍.. USB Complete: Everything You Need to Develop USB Peripherals, Third Edition by Jan Axelson
標簽： Peripherals Everything USB Complete
上傳時間： 2014-01-03
上傳用戶：671145514
AVR單片機USB口轉換為UART異步串行口的詳細程序，非常好用
標簽： UART AVR USB 單片機
上傳時間： 2016-04-18
上傳用戶：腳趾頭
蟲蟲下載站版權所有 京ICP備2021023401號-1
