<strike id="6k688"></strike>
數字與模擬電路設計技巧IC與LSI的功能大幅提升使得高壓電路與電力電路除外，幾乎所有的電路都是由半導體組件所構成，雖然半導體組件高速、高頻化時會有EMI的困擾，不過為了充分發揮半導體組件應有的性能，電路板設計與封裝技術仍具有決定性的影響。 模擬與數字技術的融合由于IC與LSI半導體本身的高速化，同時為了使機器達到正常動作的目的，因此技術上的跨越競爭越來越激烈。雖然構成系統的電路未必有clock設計，但是毫無疑問的是系統的可靠度是建立在電子組件的選用、封裝技術、電路設計與成本，以及如何防止噪訊的產生與噪訊外漏等綜合考慮。機器小型化、高速化、多功能化使得低頻/高頻、大功率信號/小功率信號、高輸出阻抗/低輸出阻抗、大電流/小電流、模擬/數字電路，經常出現在同一個高封裝密度電路板，設計者身處如此的環境必需面對前所未有的設計思維挑戰，例如高穩定性電路與吵雜(noisy)性電路為鄰時，如果未將噪訊入侵高穩定性電路的對策視為設計重點，事后反復的設計變更往往成為無解的夢魘。模擬電路與高速數字電路混合設計也是如此，假設微小模擬信號增幅后再將full scale 5V的模擬信號，利用10bit A/D轉換器轉換成數字信號，由于分割幅寬祇有4.9mV，因此要正確讀取該電壓level并非易事，結果造成10bit以上的A/D轉換器面臨無法順利運作的窘境。另一典型實例是使用示波器量測某數字電路基板兩點相隔10cm的ground電位，理論上ground電位應該是零，然而實際上卻可觀測到4.9mV數倍甚至數十倍的脈沖噪訊(pulse noise)，如果該電位差是由模擬與數字混合電路的grand所造成的話，要測得4.9 mV的信號根本是不可能的事情，也就是說為了使模擬與數字混合電路順利動作，必需在封裝與電路設計有相對的對策，尤其是數字電路switching時，ground vance noise不會入侵analogue ground的防護對策，同時還需充分檢討各電路產生的電流回路(route)與電流大小，依此結果排除各種可能的干擾因素。以上介紹的實例都是設計模擬與數字混合電路時經常遇到的瓶頸，如果是設計12bit以上A/D轉換器時，它的困難度會更加復雜。
上傳時間： 2013-11-16
上傳用戶：731140412
This document provides practical, common guidelines for incorporating PCI Express interconnect layouts onto Printed Circuit Boards (PCB) ranging from 4-layer desktop baseboard designs to 10- layer or more server baseboard designs. Guidelines and constraints in this document are intended for use on both baseboard and add-in card PCB designs. This includes interconnects between PCI Express devices located on the same baseboard (chip-to-chip routing) and interconnects between a PCI Express device located “down” on the baseboard and a device located “up” on an add-in card attached through a connector. This document is intended to cover all major components of the physical interconnect including design guidelines for the PCB traces, vias and AC coupling capacitors, as well as add-in card edge-finger and connector considerations. The intent of the guidelines and examples is to help ensure that good high-speed signal design practices are used and that the timing/jitter and loss/attenuation budgets can also be met from end-to-end across the PCI Express interconnect. However, while general physical guidelines and suggestions are given, they may not necessarily guarantee adequate performance of the interconnect for all layouts and implementations. Therefore, designers should consider modeling and simulation of the interconnect in order to ensure compliance to all applicable specifications. The document is composed of two main sections. The first section provides an overview of general topology and interconnect guidelines. The second section concentrates on physical layout constraints where bulleted items at the beginning of a topic highlight important constraints, while the narrative that follows offers additional insight.
上傳時間： 2013-10-15
上傳用戶：busterman
Abstract: The rapid build out of today's smart grid raises a number of security questions. In this article,we review two recent well-documented security breaches and a report of a security gap. These situationsinclude a 2009 smart-meter hack in Puerto Rico; a 2012 password discovery in grid distributionequipment; and insecure storage of a private key in distribution automation equipment. For each of theseattacks, we examine the breach, the potential threat, and secure silicon methods that, as part of acomplete security strategy, can help thwart the attacks.
上傳時間： 2013-10-27
上傳用戶：tecman
Abstract: This document details the Lakewood (MAXREFDES7#) subsystem reference design, a 3.3V input, ±12V (±15V) output, isolated power supply. The Lakewood reference design includes a 3W primary-side transformer H-bridge driver for isolated supplies, and two wide input range and adjustable output low-dropout linear regulators (LDOs). Test results and hardware files are included.
標簽： MAXREFDES Lakewood Isolated Output
上傳時間： 2013-11-02
上傳用戶：fengzimili
Abstract: Some power architectures require the power supply sequencer (or system manager) to controldownstream power MOSFETs to allow power to flow into branch circuits. This application note explains howsystem power sequencing and level shifting can be accomplished using a low-voltage system manager
上傳時間： 2013-11-02
上傳用戶：wys0120
Abstract: Uses the MAX641 switching controller and an external discrete charge pump to step up the input voltage. This circuitcan service low loads and is efficient when the output is two, three, four times the input voltage. Adding the MAX627 MOSdriver can further increase the output current capability.
上傳時間： 2013-11-15
上傳用戶：zwei41
Abstract: Some types of loads require more current during startup than when running. Other loads can be limited to a lower-powercurrent during startup but require a higher operating current. This article describes an application circuit that automatically adjusts apower circuit’s overcurrent protection level up or down after startup is complete.
上傳時間： 2013-10-23
上傳用戶：swaylong
In this paper, two types of MMIC voltage controlled oscillators have been successfully demonstrated. The first chip with single tuning diode shows the excellent tuning linearity. The second chip with two tuning diodes can improve the tuning bandwidth.
上傳時間： 2013-10-17
上傳用戶：xjz632
The MAX14885E, a 2:2 VGA switch, connects a VGA source to a VGA monitor. To ease direct connection to graphics controllers orthe ASIC, the MAX14885E has two supplies: VCC, a 5V ±5% supply, drives the VGA side interface; and the VL supply sets the logicswitching thresholds on the digital input pins (EN, S00, S01, S10, S11, SHA, SHB, SVA, and SVB). This application note documentsthe proper sequencing of the VCC and VL power supplies on power-up.
上傳時間： 2013-10-23
上傳用戶：wuchunzhong
Although recent popular attention is focused on LithiumIon batteries, one must not forget that other batterychemistries, such as Nickel Cadmium (NiCd) and NickelMetal Hydride (NiMH) have advantages in rechargeablepower systems. Nickel-based batteries are robust, capableof high discharge rates, have good cycle life, do notrequire special protection circuitry and are less expensivethan Li-Ion. Among the two, NiMH batteries are rapidlyreplacing NiCd because of their higher capacity (40% to50% more) and the environmental concerns of the toxiccadmium contained in NiCd batteries.
上傳時間： 2013-11-04
上傳用戶：qq10538412
