基于FPGA設計的相關論文資料大全 84篇用FPGA實現FFT的研究 劉朝暉 韓月秋 摘 要 目的 針對高速數字信號處理的要求，給出了用現場可編程門陣列(FPGA)實現的 快速傅里葉變換(FFT)方案.方法 算法為按時間抽取的基4算法，采用遞歸結構的塊浮點運 算方案，蝶算過程只擴展兩個符號位以適應雷達信號處理的特點，乘法器由陣列乘法器實 現.結果 采用流水方式保證系統的速度，使取數據、計算旋轉因子、復乘、DFT等操作協 調一致，在計算、通信和存儲間取得平衡，避免了瓶頸的出現.結論 實驗表明，用FPGA 實現高速數字信號處理的算法是一個可行的方案. 關鍵詞 離散傅里葉變換； 快速傅里葉變換； 塊浮點運算； 可編程門陣列 分類號 TP39； TN957.511 Implementation of FFT with FPGA Technology Liu Zhaohui Han Yueqiu (Department of Electronics Engineering, Beijing Institute of Technology, Beijing 100081) Abstract Aim To propose a scheme for implementing FFT with FPGA in accor-dance with the requirement for high speed digital signal processing. Methods The structure of FPGA and requirement of system were considered in the experiment, radix-4 algorithm of DIT and recursive structure were adopted. The group float point arithmetic operation was used in the butterfly and the array multiplier was used to realize multiplication. Results The pipeline pattern was used to ensure the system speed, it made fetching data, calculating twiddle factor, complex multiplication and D
標簽： fpga
上傳時間： 2022-03-23
上傳用戶：
針對嵌入式產品程序更新問題,提出了一種基于IAP技術的STM32單片機在線固件升級方案,設計了STM32單片機最小系統硬件電路和USB轉串口通信電路,并給出了Bootloader程序、APP程序、PC上機程序的實現流程.實驗結果表明,該方案具有簡單實用、穩定性高、維護成本低和設備使用效率高的特點,適用于嵌入式產品升級.For the problem of updating embedded products program,an online firmware upgrade scheme of STM32 single chip microcomputer based on IAP technology is proposed.This scheme not only elaborates the principle of IAP technology in detail but also provides the design of the minimum system hardware circuit of STM32 MCU,the design of USB for serial communication circuit,and the implementation flow of Bootloader program,APP program and PC program.The experiment Results show that the scheme is simple,practical and highly stable.In addition,it can be used to actual embedded product upgrading,significantly reducing maintenance costs and improving the efficiency of equipment.
上傳時間： 2022-03-25
上傳用戶：
對某四輪獨立驅動電動汽車輪轂電機進行研究,設計一種永磁無刷直流電機控制器.以STM32F103RBT6芯片為基礎,對電機驅動電路、采樣電路和保護電路分別進行硬件設計與分析;同時,采用模塊化軟件設計方案,對該控制器的軟件系統進行升級.實驗驗證表明:所設計的電機控制器能使電機響應迅速、轉速穩定、無超調,且電動車動力輸出性能良好.A permanent magnet brushless direct current motor controller was designed by studying the hub motor of a four-wheel independent drive electric vehicle.Based on STM32 F103RBT6 chip,the hardware design and analysis of motor drive circuit,sampling circuit and protection circuit were carried out respectively.At the same time,modular software design scheme was adopted to upgrade the software system of the controller.Experimental Results show that the designed motor controller can ensure the motor fast response,stable speed,no overshoot,and good power output performances.
上傳時間： 2022-03-26
上傳用戶：qingfengchizhu
文章提出了一種基于AT89S51單片機的智能家居系統的設計,該系統具有室內煤氣以及煙霧的檢測、家庭室內防盜等功能。文章詳細分析了系統的總體設計,詳盡分析并設計了煤氣傳感器模塊、煙霧傳感器模塊、人體紅外感應傳感器模塊、報警模塊等各硬件部分,并利用PROTUES軟件進行了系統仿真。仿真結果證明:系統具有成本低、效率高、操作方便等優點,達到了預期設計的效果。This paper presents the design of an intelligent home system based on AT89S51 microcontroller.The system has the functions of detecting indoor gas and smoke,guarding against theft in the home,and so on.The overall design of the system is analyzed in detail.The gas sensor module,smoke sensor module,human infrared sensor module,alarm module and other hardware parts are analyzed and designed in detail,and the system simulation is carried out using PROTUES software.The simulation Results show that the system has the advantages of low cost,high efficiency,convenient operation and so on,and achieves the expected design effect.
上傳時間： 2022-03-28
上傳用戶：
為設計高效率、低損耗的PFC電路,本文基于UCC28019進行電路設計。以UCC28019輸出的PWM波形來控制Boost升壓斬波為核心電路,使電路中的電容交替地充放電、電感交替的儲存和釋放能量,最后實現在輸入AC20V~24V電壓情況下穩定輸出DC38V。測試結果表明,系統實現效率為95%左右,電壓調整率小于1%,電源功率因數0.99。交流輸入電壓為19.0-25.8 V時,輸出直流電壓穩定性較好,電感無明顯嘯叫且紋波小,具有一定的帶負載能力和實用性。In order to design the PFC circuit with high efficiency and low loss,this paper designs the circuit based on UCC28019.The PWM waveform output by UCC28019 is used to control boost chopper as the core circuit,which alternately charges and discharges capacitors,stores and releases energy by inductors,and finally achieves stable output of DC38 V under the input voltage of AC20 V~24 V.The test Results show that the system achieves about 95% efficiency,the voltage adjustment rate is less than 1%,the power factor is 0.99,and the AC input voltage is 19.0-25.8 V.The output DC voltage stability is good,the inductance has no obvious whistle and the ripple is small,so it has certain load capacity and practicability.
上傳時間： 2022-04-03
上傳用戶：
目的:自主研制一款超聲手術刀電源控制系統,以減少能量的消耗,維持手術刀的正常溫度。方法:對超聲換能器在諧振附近的等效電路建立模型,并設計基于數字信號處理(DSP)的超聲手術刀的硬件控制系統。結果:經對電源控制系統的電路和工作性能測試,生成的電流和電壓的有效值等參數,能夠及時調整電源的頻率,并達到預期的功能指標,使超聲手術刀工作在諧振狀態。結論:以DSP為核心設計的超聲手術刀電源控制系統,測試指標均能夠達到預期的要求,能夠使系統在諧振狀態下工作。Objective: To independently develop a power control system of ultrasonic scalpel so as to reduce the energy consumption and maintain the normal temperature of ultrasonic scalpel. Methods: In this paper, the model of equivalent circuit of ultrasonic transducer nearby syntony was built up, and the hardware control system of ultrasonic scalpel based on digital signal processing(DSP) was designed. Results: Through testing the circuit and work performance of power control system, the series of parameters such as effective value and so on which were produced by this system could adjust frequency of power source in time and attain anticipative functional indicator, and it took the ultrasonic scalpel to work in syntonic situation. Conclusion: The tested indicators of power control system of ultrasonic scalpel based on the kernel design of DSP can attain anticipative requirement, and can take this system to work in syntonic situation.
上傳時間： 2022-04-03
上傳用戶：bluedrops
本文首次設計并驗證了基于macom三合一芯片設計的光模塊電路,該電路旨在提供一種滿足SFF-8472中規定的數字診斷功能的低成本SFP+模塊。電路采用激光器驅動、限幅放大器、控制器以及時鐘恢復單元集成的單芯片,在保證高精度數字診斷功能基礎上,實現了低成本高可靠的特點。該電路在光接收接口組件與激光器驅動和限幅放大器單元的限幅放大器部分之間接入濾波器來提高模塊的靈敏度及信號質量。在控制器單元的數字電位器的引腳上采用外加電阻的方式避免出現上電不發光的故障問題。該研究結果為下一代SFP-DD光模塊設計與開發工作,奠定了一定的理論與實踐基礎。This paper designs and validates the optical module circuit based on the MACOM Trinity chip for the first time.This circuit aims to provide a low-cost SFP module which meets the digital diagnosis function specified in SFF-8472.The circuit uses a single chip integrated with laser driver,limiting amplifier,controller and clock recovery unit.On the basis of ensuring high precision digital diagnosis function,it achieves the characteristics of low cost and high reliability.The circuit connects a filter between the optical receiving interface module and the limiting amplifier part of the laser driver and limiting amplifier unit to improve the sensitivity and signal quality of the module.The pin of the digital potentiometer in the controller unit is equipped with an external resistance to avoid the problem of power failure.The research Results lay a theoretical and practical foundation for optical module design in high-speed data center.
上傳時間： 2022-04-03
上傳用戶：
以單片機控制A/D轉換器TLC549為例,對A/D轉換器的主要技術指標進行了分析研究,在Proteus平臺下,完成了A/D轉換電路的構建,采用器件工作時序方式進行程序編寫,借助仿真圖表、虛擬儀器等工具對A/D轉換的數據進行測量并對失調誤差、增益誤差、微分非線性、積分非線性和轉換時間等重要參數進行了詳細分析。結果表明:使用Proteus軟件可對A/D轉換過程進行定性分析,將抽象的A/D轉換器技術指標直觀化、形象化展現出來,有助于學生更好地理解A/D轉換過程。The main technical indicators of A/D converter were analyzed and studied with an example from A/D converter TLC2543 which is controlled by using SCM.It was completed the construction of the A/D converter circuit under the Proteus software.The programming based on the operation sequence of the chip is put forward.With the aid of the simulation tools such as virtual instrument,simulation charts provided by Proteus,the important parameters of circuit such as offset error,gain error,differential nonlinearity(DNL),integral nonlinearity (INL) and conversion time are analyzed detailedly.Simulation Results show that the A/D conversion process can be qualitatively analyzed and visualized the abstract indicators of A/D.The system can help students better to understand the SCM conversion process.
上傳時間： 2022-04-04
上傳用戶：
為了提高超高頻RFID系統中閱讀器在低信噪比的情況下仍具有較高的識別能力,提出一種基于FPGA系統結合軟件無線電方法實現超高頻RFID射頻前端電路方案。超高頻射頻識別系統必須符合EPC Class 1generation 2標準,所設計的電路系統以Xilinx公司的XC6SLX16-2CSG324FPGA芯片為硬件基礎,將數字基帶調制解調和中頻濾波電路在FPGA系統中設計實現,重點闡述了射頻前端電路的設計結構、AD/DA轉換電路,以及數字濾波器的設計。實驗結果表明,所設計的超高頻RFID閱讀器簡化了前端電路系統結構,提升了穩定性,增強了抗干擾能力。該電路系統在信噪比較低的情況下,能夠較好地實現915MHz頻率的射頻接收和發送。In order to improve the reader UHF RFID system still has a higher ability to identify,in the case of low signal-to-noise ratio.The UHF RFID systems must comply with EPC Class 1 generation 2 standard.In this paper,the design of the circuit system based on Xilinx＇s XC6SLX16-2CSG324 FPGA chip,and presents UHF RFID RF front-end circuit with software radio based on FPGA system.Digital baseband modem and IF filter circuit is designed and implemented in the FPGA system,and focused on designing the structure of the RF front-end circuit,AD/DA conversion circuits,and digital filter.Experimental Results show that the UHF RFID reader de...
標簽： 915mhz 超高頻 rfid 閱讀 射頻 前端 電路 設計
上傳時間： 2022-04-17
上傳用戶：shjgzh
介紹一種萬能模擬信號輸入采集電路,可以同時支持電壓、電流、熱電偶、熱電阻等常見的工業類型信號,方便后級電路的測量。該研究成果通過不斷優化和完善,已成功應用到了中控儀表的新產品中。The paper introduces a collection circuit of universal signal input. The circuit support voltage, current, thermocouple, thermal resistance and other common industrial type signal. The research Results, which has been continuous optimized and improved, has been successfully applied to the new production of Zhejiang Supcon Instrument Co., Ltd.
標簽： 采集電路
上傳時間： 2022-04-21
上傳用戶：slq1234567890
