Linear Technology’s High Frequency Product lineupincludes a variety of RF I/Q modulators. The purpose ofthis application note is to illustrate the circuits requiredto interface these modulators with several popular D/Aconverters. Such circuits typically are required to maximizethe voltage transfer from the DAC to the baseband inputsof the modulator, as well as provide some reconstructionfi ltering.
上傳時間： 2013-10-19
上傳用戶：FreeSky
噪聲系數(NF)是RF系統設計師常用的一個參數，它用于表征RF放大器、混頻器等器件的噪聲，并且被廣泛用作無線電接收機設計的一個工具。許多優秀的通信和接收機設計教材都對噪聲系數進行了詳細的說明(例如參考文獻1)，本文重點討論該參數在數據轉換器中的應用。
上傳時間： 2013-11-05
上傳用戶：李彥東
Radio Frequency Integrated Circuit Design I enjoyed reading this book for a number of reasons. One reason is that itaddresses high-speed analog design in the context of microwave issues. This isan advanced-level book, which should follow courses in basic circuits andtransmission lines. Most analog integrated circuit designers in the past workedon applications at low enough frequency that microwave issues did not arise.As a consequence, they were adept at lumped parameter circuits and often notcomfortable with circuits where waves travel in space. However, in order todesign radio frequency (RF) communications integrated circuits (IC) in thegigahertz range, one must deal with transmission lines at chip interfaces andwhere interconnections on chip are far apart. Also, impedance matching isaddressed, which is a topic that arises most often in microwave circuits. In mycareer, there has been a gap in comprehension between analog low-frequencydesigners and microwave designers. Often, similar issues were dealt with in twodifferent languages. Although this book is more firmly based in lumped-elementanalog circuit design, it is nice to see that microwave knowledge is brought inwhere necessary.Too many analog circuit books in the past have concentrated first on thecircuit side rather than on basic theory behind their application in communications.The circuits usually used have evolved through experience, without asatisfying intellectual theme in describing them. Why a given circuit works bestcan be subtle, and often these circuits are chosen only through experience. Forthis reason, I am happy that the book begins first with topics that require anintellectual approach—noise, linearity and filtering, and technology issues. Iam particularly happy with how linearity is introduced (power series). In therest of the book it is then shown, with specific circuits and numerical examples,how linearity and noise issues arise.
上傳時間： 2014-12-23
上傳用戶：han_zh
高速數據轉換器評估平臺(HSDCEP)是基于PC的平臺，提供評估Maxim RF數/模轉換器(RF-DAC，支持更新速率≥ 1.5Gsps)和Maxim數字上變頻器(DUC)的齊全工具。HSDCEP可以在每對數據引腳產生速率高達1.25Gbps的測試碼型，支持多達4條并行16位LVDS總線。通過USB 2.0端口將最長64兆字(Mw)、每字16位寬的數據碼型裝載至HSDCEP存儲器
上傳時間： 2013-10-25
上傳用戶：zycidjl
成功的 RF 設計必須仔細注意整個設計過程中每個步驟及每個細節 這意味著必須在設計開始階段就要進行徹底的 仔細的規劃 并對每個設計步驟的進展進行全面持續的評估 而這種細致的設計技巧正是國內大多數電子企業文化所欠缺的 近幾年來，由于藍芽設備無線局域網絡（WLAN）設備和行動電話的需求與成長 促使業者越來越關注 RF 電路設計的技巧 從過去到現在 RF 電路板設計如同電磁干擾（EMI）問題一樣 一直是工程師們最難掌控的部份 甚至是夢魘 若想要一次就設計成功 必須事先仔細規劃和注重細節才能奏效
上傳時間： 2013-11-13
上傳用戶：liuwei6419
DSP系統的降噪技術,PowerPCB在印制電路板設計中的應用技術,PCB互連設計過程中最大程度降低RF效應的基本方法
標簽： PCB
上傳時間： 2013-10-11
上傳用戶：gmh1314
高速PCB設計指南之（一~八 ）目錄 2001/11/21 一、1、PCB布線2、PCB布局3、高速PCB設計 二、1、高密度（HD）電路設計2、抗干擾技術3、PCB的可靠性設計4、電磁兼容性和PCB設計約束 三、1、改進電路設計規程提高可測性2、混合信號PCB的分區設計3、蛇形走線的作用4、確保信號完整性的電路板設計準則 四、1、印制電路板的可靠性設計 五、1、DSP系統的降噪技術2、POWERPCB在PCB設計中的應用技術3、PCB互連設計過程中最大程度降低RF效應的基本方法 六、1、混合信號電路板的設計準則2、分區設計3、RF產品設計過程中降低信號耦合的PCB布線技巧 七、1、PCB的基本概念2、避免混合訊號系統的設計陷阱3、信號隔離技術4、高速數字系統的串音控制 八、1、掌握IC封裝的特性以達到最佳EMI抑制性能2、實現PCB高效自動布線的設計技巧和要點3、布局布線技術的發展 注：以上內容均來自網上資料，不是很系統，但是對有些問題的分析還比較具體。由于是文檔格式，所以缺圖和表格。另外，可能有小部分內容重復。
上傳時間： 2014-05-15
上傳用戶：wuchunzhong
這里僅討論電容及電感值的選取。種類的選取,則需要更多的工程實踐,更多的RF電路的經驗,這里不再討論。從理論上講,隔直電容、旁路電容的容量應滿足。顯然,在任何角頻率下,這在工程上是作不到的。電容量究竟取多大是合理的呢？圖1-5(a),(b)給出了隔直電容(多數情況下,這個電容又稱為耦合電容)和旁路電容的使用簡化
上傳時間： 2013-11-12
上傳用戶：13188549192
Abstract: Impedance mismatches in a radio-frequency (RF) electrical transmission line cause power loss andreflected energy. Voltage standing wave ratio (VSWR) is a way to measure transmission line imperfections. Thistutorial defines VSWR and explains how it is calculated. Finally, an antenna VSWR monitoring system is shown.
上傳時間： 2013-10-19
上傳用戶：yuanwenjiao
Abstract: In battery-powered RF transmitters such as garage door openers and remote keyless entry for cars, as the battery drains,
上傳時間： 2013-10-23
上傳用戶：nanxia
