設計了一種基于PIC16C71單片機的數字水溫配制閥。該配制閥采用NTC熱敏電阻作溫度傳感器，與固定電阻組成簡單分壓電路作為水溫測量電路，利用PIC16C71單片機內置的8位A/D轉換器把熱敏電阻上的模擬電壓轉換為數字量，PIC16C71單片機控制直流電機驅動混水閥調節冷熱水的混合比例實現水溫調節。給出了控制電路圖，對水溫測量電路的參數選擇和測溫精度作了詳細討論。實驗和分析表明，選用阻值較大的NTC熱敏電阻和分壓電阻可較好地解決熱敏電阻因功耗較大造成的熱擊穿問題。 Abstract: A digital valve for controlling water temperature based on PIC16C71 was presented in this paper.A bleeder circuit which consisted of a NTC thermistor as temperature sensor and a fixed resistance was designed as water temperature measuring circuit.The analog voltage on the thermistor was converted into digital signal by a 8-bit A/D converter embedded in PIC16C71. Based on the digital signal， the MCU PIC16C71 drived the valve by a DC motor to adjust the water temperature through adjusting the proportion of hot water and cold water.The circuit diagram of controller was given，the principle，the component parameters and the accuracy of measuring temperatures were also dissertated in detail. It was found by experiment and analysis that thermal breakdown of thermistor caused by high power could be solved by selecting thermistor and fixed resistance with high impedance value.
上傳時間： 2013-11-08
上傳用戶：Yue Zhong
以C8051F020為核心處理器，設計無線傳感器網絡數據采集系統。系統采用SZ05-ADV型無線通訊模塊組建Zigbee無線網絡，結合嵌入式系統的軟硬件技術，完成終端節點的8路傳感器信號的數據采集。現場8路信號通過前端處理后，分別送入C8051F020的12位A/D轉換器進行轉換。經過精確處理、存儲后的現場數據，通過Zigbee無線網絡傳送到上位機，系統可達到汽車試驗中無線測試的目的。 Abstract: This paper designs a wireless sensor network system for data acquisition with C8051F020 as core processors.The system used SZ05-ADV wireless communication module，set up a Zigbee wireless network， combined with hardware and software technologies of embedded systems，completed the end-node 8-locale sensor signal data acquisition.Eight locale signals were sent separately into the 12-bit ADC of C8051F020 for conversion through front treatment.After accurate processing and storage，the locale data was transmitted to the host computer through Zigbee wireless.The system achieves the purpose of wireless testing in vehicle trial.
標簽： C8051F020 Zigbee 汽車測試 系統設計
上傳時間： 2013-11-23
上傳用戶：dsgkjgkjg
提出了一種以S3C2440A為核心處理器的銀行評價器的設計方案，并結合XILINX公司的XL95144XL型CPLD，輔助S3C2440A，實現該銀行評價器的各部分功能以及系統信號之間的相互協調。該評價器在系統設計上采用液晶屏顯示，代替了以往簡單的數碼管電路的顯示模式，在視覺上給人以全新的享受。同時，評價器增加了新的網絡供電方式，只要將評價器連接上網絡就可以正常工作，方便了客戶的使用。總之，此款銀行評價器采用了嵌入式系統的設計方案，大大豐富了系統功能，實現一個銀行評價器設計的新突破。 Abstract: S3C2440A of SamSung company is the core component of the embedded system. A design of bank assessor based on S3C2440A was provided in this paper. It used XL95144XL combined with S3C2440A to realize all the functions and coordination with system signals. This bank assessor used LCD to display instead of the former simple digital display and provided a new seusuous enjoment. Meanwhile，it provided a new method of network power supply，that the bank assessor could regularly work once it connected to the network，which is convenient for customers to use. In a word，this assessor takes embedded system，enriches the system’s functions and reclizes a new breakout.
標簽： S3C2440A
上傳時間： 2013-11-03
上傳用戶：taa123456
MMC/SD卡以其優越的性能，在單片機嵌入式設備中得到廣泛應用。將MMC/SD卡作為外部掉電存儲介質應用于音頻信號發生器中，通過8051F330單片機上的SPI接口，實現單片機—MMC/SD卡的存儲擴展，設計了此硬件平臺上的MMC/SD卡的單片機驅動程序，并給出了相應的程序代碼，滿足音頻信號發生器的大容量存儲要求。 Abstract: MMC/SD card is more and more widely used in the single chip embedded devices for their excellent performances.This article introduces the application of MMC/SD card as the external power down storage medium in audio signal generator. The extension technology especially for storage of single chip-MMC/SD card via SPI interfaces in 8051F330 single chip, including designs single chip drive program of MMC/SD card based on hardware platform,and also gives the key coding of the program. The implementation of big capacity storage is meaningful in audio signal generator.
上傳時間： 2014-12-27
上傳用戶：黃華強
以AVR單片機ATmega8和USB接口器件PDIUSBD12為核心，基于標準的USB1.1協議，設計一種通用USB接口模塊，以滿足嵌入式系統中對USB接口的需求。對模塊的硬件電路或單片機固件程序的硬件接口層稍加修改即可用于其他各種微處理器。該模塊可為各種嵌入式系統增加USB接口,實現與USB主機系統通信。 Abstract: Based on AVR microcontroller ATmega8 and USB interface chip PDIUSBD12, a general USB interface module is designed according to USB1.1 protocol for various requirements of embedded systems. Only with few modifications in circuit or hardware abstract layer of firmware, the module can be used on many types of microprocessors. All kinds of embedded systems can realize high speed and stable communication with USB host systems, owing to the facility of this module.
上傳時間： 2014-01-08
上傳用戶：趙云興
介紹了MPC555與CS8900A擴展以太網的硬件設計圖。以NUCLUES PLUS操作系統為基礎，介紹了網卡軟件驅動程序的編制，給出了以太網協議包嵌入NUCLEUS PLUS操作系統的實現方法。 Abstract: The Ethernet extension hardware design of MPC555 and CS8900A are introduced,and the software driven program based on NUCLEUS PLUS operation system and the technique that Ethernet protocol embedded in NUCLEUS PLUS real operation system are discussed.
上傳時間： 2013-10-23
上傳用戶：xiehao13
在需要實時大量輸入漢字的顯示控制處理應用中，利用傳統單片機實現顯示控制的設計方法是較難實現的。帶漢字字庫的液晶模塊的使用使得小容量ROM單片機的大量漢字信息輸入與顯示成為可能。提出了針對漢字字庫編碼的二級索引拼音輸入檢索方法,介紹了以ST7920作為控制器的帶漢字字庫的液晶顯示模塊的接口方法及漢字顯示和控制原理，給出了通用計算機鍵盤在單片機中的串行接口，采用該技術可大大增強單片機的漢字輸入功能。為小容量ROM單片機的大批量漢字信息處理提供了一種漢字輸入解決方案。 Abstract: It is difficult to realize Chinese characters input method based on the embedded system by using the traditional design method of display control. It is possible to input and display Chinese characters based on the embedded system with the ROM of small content by using the LCD module with Chinese characters.Chinese characters input method of the quadric index recall in allusion to Chinese characters code is brought forward.The interface and the principle of Chinese characters display control based on the LCD module controlled with the ST7920 is introduced too.The serial interface of the computer keyboard in common use and the embedded system is given at the same time. It can enhance the embedded system function of Chinese characters input by using this technology, and provide a kind of Chinese characters input scheme for the embedded system with small capacity ROM.
上傳時間： 2013-11-19
上傳用戶：jhksyghr
針對船舶氣象儀保障維修而設計的船舶氣象儀測試系統，包括信息處理終端、主儀器檢測模塊、傳感器檢測模塊，各個模塊都采用基于AVR單片機的嵌入式系統，模塊之間通過CAN總線進行通信。結果表明，船舶氣象儀測試系統能夠快速檢測船舶氣象儀故障，與單純依靠人工方式排查故障相比，故障檢測時間縮短了60%以上。 Abstract: The test system of ship meteorological instrument was developed to satisfy the maintenance of ship meteorological instruments，which composed of information processing terminal， testing module of main instrument and testing module of sensors. Each of these modules included an embedded system based on microcontroller of AVR series and communicated with other module by CAN bus. The results show that the test system can judge the fault of ship meteorological instrument quickly and shorten the fault detection time as much as 60% compared with simple manual troubleshooting.
上傳時間： 2013-11-23
上傳用戶：stvnash
第一章 序論……………………………………………………………6 1- 1 研究動機…………………………………………………………..7 1- 2 專題目標…………………………………………………………..8 1- 3 工作流程…………………………………………………………..9 1- 4 開發環境與設備…………………………………………………10 第二章 德州儀器OMAP 開發套件…………………………………10 2- 1 OMAP介紹………………………………………………………10 2-1.1 OMAP是什麼?…….………………………………….…10 2-1.2 DSP的優點……………………………………………....11 2- 2 OMAP Architecture介紹………………………………………...12 2-2-1 OMAP1510 硬體架構………………………………….…12 2-2.2 OMAP1510軟體架構……………………………………...12 2-2.3 DSP / BIOS Bridge簡述…………………………………...13 2- 3 TI Innovator套件 -- OMAP1510 ……………………………..14 2-2.1 General Purpose processor -- ARM925T………………...14 2-2.2 DSP processor -- TMS320C55x …………………………15 2-2.3 IDE Tool – CCS …………………………………………15 2-2.4 Peripheral ………………………………………………..16 第三章 在OMAP1510上建構Embedded Linux System…………….17 3- 1 嵌入式工具………………………………………………………17 3-1.1 嵌入式程式開發與一般程式開發之不同………….….17 3-1.2 Cross Compiling的GNU工具程式……………………18 3-1.3 建立ARM-Linux Cross-Compiling 工具程式………...19 3-1.4 Serial Communication Program………………………...20 3- 2 Porting kernel………………………………………………….…21 3-2.1 Setup CCS ………………………………………….…..21 3-2.2 編譯及上傳Loader…………………………………..…23 3-2.3 編譯及上傳Kernel…………………………………..…24 3- 3 建構Root File System………………………………………..…..26 3-3.1 Flash ROM……………………………………………...26 3-3.2 NFS mounting…………………………………………..27 3-3.3 支援NFS Mounting 的kernel…………………………..27 3-3.4 提供NFS Mounting Service……………………………29 3-3.5 DHCP Server……………………………………………31 3-3.6 Linux root 檔案系統……………………………….…..32 3- 4 啟動及測試Innovator音效裝置…………………………..…….33 3- 5 建構支援DSP processor的環境…………………………...……34 3-5.1 Solution -- DSP Gateway簡介……………………..…34 3-5.2 DSP Gateway運作架構…………………………..…..35 3- 6 架設DSP Gateway………………………………………….…36 3-6.1 重編kernel……………………………………………...36 3-6.2 DEVFS driver…………………………………….……..36 3-6.3 編譯DSP tool和API……………………………..…….37 3-6.4 測試……………………………………………….…….37 第四章 MP3 Player……………………………………………….…..38 4- 1 MP3 介紹………………………………………………….…….38 4- 2 MP3 壓縮原理……………………………………………….….39 4- 3 Linux MP3 player – splay………………………………….…….41 4.3-1 splay介紹…………………………………………….…..41 4.3-2 splay 編譯………………………………………….…….41 4.3-3 splay 的使用說明………………………………….……41 第五章 程式改寫………………………………………………...…...42 5-1 程式評估與改寫………………………………………………...…42 5-1.1 Inter-Processor Communication Scheme…………….....42 5-1.2 ARM part programming……………………………..…42 5-1.3 DSP part programming………………………………....42 5-2 程式碼………………………………………………………..……43 5-3 雙處理器程式開發注意事項…………………………………...…47 第六章 效能評估與討論……………………………………………48 6-1 速度……………………………………………………………...48 6-2 CPU負載………………………………………………………..49 6-3 討論……………………………………………………………...49 6-3.1分工處理的經濟效益………………………………...49 6-3.2音質v.s 浮點與定點運算………………………..…..49 6-3.3 DSP Gateway架構的限制………………………….…50 6-3.4減少IO溝通……………….………………………….50 6-3.5網路掛載File System的Delay…………………..……51 第七章 結論心得…
上傳時間： 2013-10-14
上傳用戶：a471778
Bootloader是微處理器上電時運行的第一段代碼，它可以通過通信接口實現對微處理器內部應用程序的更新升級，為網絡化嵌入式產品的應用程序升級帶來極大的便利。由于目前沒有統一嵌入式系統的Bootloader。基于NEC 78K0系列單片機自編程原理，設計出一個適用于78K0/Fx2系列單片機的Bootloader，并能夠通過單片機串口在線升級應用程序。 Abstract: Bootloader is the first piece of code executed after microprocessor startup. It makes the embedded product’s firmware update conveniently through communication interface. However， no unified bootloader is available for all kinds of microprocessor products. Based on the principle of self-programming NEC 78K0s’ series， a useful Bootloader which is suitable for 78K0/Fx2s’ series MCU is designed，the design can update the application through serial ports.
標簽： Bootloader MCU 自編程
上傳時間： 2013-10-26
上傳用戶：fang2010
