The CC1101 is a low-cost sub- 1 GHztransceiver designed for very low-powerwireless applications. The circuit is mainlyintended for the ISM (Industrial, Scientific andMedical) and SRD (Short Range Device)frequency bands at 315, 433, 868, and 915MHz, but can easily be programmed foroperation at other frequencies in the 300-348MHz, 387-464 MHz and 779-928 MHz bands.CC1101 is an improved and code compatibleversion of the CC1100 RF transceiver. Themain improvements on the CC1101 include:
上傳時間： 2013-11-12
上傳用戶：363186
The LPC2292/2294 microcontrollers are based on a 16/32-bit ARM7TDMI-S CPU with real-time emulation and embedded trace support, together with 256 kB of embedded high-speed flash memory. A 128-bit wide memory interface and a unique accelerator architecture enable 32-bit code execution at the maximum clock rate. For critical code size applications, the alternative 16-bit Thumb mode reduces code by more than 30 pct with minimal performance penalty. With their 144-pin package, low power consumption, various 32-bit timers, 8-channel 10-bit ADC, 2/4 (LPC2294) advanced CAN channels, PWM channels and up to nine external interrupt pins these microcontrollers are particularly suitable for automotive and industrial control applications as well as medical systems and fault-tolerant maintenance buses. The number of available fast GPIOs ranges from 76 (with external memory) through 112 (single-chip). With a wide range of additional serial communications interfaces, they are also suited for communication gateways and protocol converters as well as many other general-purpose applications. Remark: Throughout the data sheet, the term LPC2292/2294 will apply to devices with and without the /00 or /01 suffix. The suffixes /00 and /01 will be used to differentiate from other devices only when necessary.
上傳時間： 2014-12-30
上傳用戶：aysyzxzm
Abstract: The process of designing a radio system can be complex and often involves many project tradeoffs. Witha little insight, balancing these various characteristics can make the job of designing a radio system easier. Thistutorial explores these tradeoffs and provides details to consider for various radio applications. With a focus on theindustrial, scientific, medical (ISM) bands, the subjects of frequency selection, one-way versus two-way systems,modulation techniques, cost, antenna options, power-supply influences, effects on range, and protocol selectionare explored.
標簽： 無線
上傳時間： 2013-12-13
上傳用戶：eastgan
Abstract: With industrial/scientific/medical (ISM) band radio frequency (RF) products, often times users are new to the structure of Maxim's low pin-count transmitters andfully integrated superheterodyne receivers. This tutorial provides simple steps that can be taken to get the best performance out of these transmitters and receivers whileproviding techniques to measure the overall capability of the design.
上傳時間： 2013-11-02
上傳用戶：yph853211
Abstract: This application note illustrates the flexibility of the MAX7060 ASK/FSK transmitter. While the currently available evaluationkit (EV kit) has been optimized for the device's use in a specific frequency band (i.e., 288MHz to 390MHz), this document addresseshow the EV kit circuitry can be modified for improved operation at 433.92MHz, a frequency commonly used in Europe. Twoalternative match and filter configurations are presented: one for optimizing drain efficiency, the other for achieving higher transmitpower. Features and capabilities of earlier Maxim industrial, scientific, and medical radio-frequency (ISM-RF) transmitters areprovided, allowing comparison of the MAX7060 to its predecessors. Several design guidelines and cautions for using the MAX7060are discussed.
上傳時間： 2013-11-14
上傳用戶：swaylong
通過比較各種隔離數字通信的特點和應用范圍，指出塑料光纖在隔離數字通信中的優勢。使用已經標準化的TOSLINK接口，有利于節省硬件開發成本和簡化設計難度。給出了塑料光纖的硬件驅動電路，說明設計過程中的注意事項，對光收發模塊的電壓特性和頻率特性進行全面試驗，并給出SPI口使用塑料光纖隔離通信的典型應用電路圖。試驗結果表明，該設計可為電力現場、電力電子及儀器儀表的設計提供參考。 Abstract: y comparing characteristics and applications area of various isolated digital communications， this article indicates advantages of plastic optical fiber in isolated digital communications. Using the standardized TOSLINK interface， it helps to control costs and difficulty in hardware development and design. Then it gives the hardware driver circuit of plastic optical fiber module， explains the noticed details in design process， gives results on the basis of the optical transceiver module voltage characteristics and frequency characteristics tests. Finally，it gives typical application circuit of the SPI communication port by using plastic optical fiber isolation .The results show that this design can be referenced for the power field， power electronics and instrumentation design.
上傳時間： 2014-01-10
上傳用戶：gundan
提出了一種以ARM微處理器為控制核心的遠程無線視頻監控終端的設計方案，其監控終端的硬件設計包括視頻采集處理、中央管理控制、無線傳輸3個模塊。并給出了監控終端的軟件開發平臺和開發模式的系統啟動代碼、嵌入式Linux系統移植以及驅動程序和應用程序。測試結果表明，該監控終端設計方案合理、有效，基本滿足監控需求。 Abstract: A remote wireless video monitoring terminal design， which uses ARM microprocessor as its core control， is proposed in this paper.The hardware design of monitoring terminal system is composed of the video acquisition and processing module， the central management and control module， wireless transmission module.Meanwhile the monitoring terminal-s software development platform and development patterns are designed. Also the design of the system-s start codes， embedded Linux system-s transplantation process， driver and the corresponding applications are given. The results showed that the monitoring terminal design is reasonable， effective， basically meet monitoring requirements.
上傳時間： 2013-11-13
上傳用戶：wanqunsheng
The NXP LPC314x combine a 270 MHz ARM926EJ-S CPU core, High-speed USB 2.0OTG, 192 KB SRAM, NAND flash controller, flexible external bus interface, three channel10-bit A/D, and a myriad of serial and parallel interfaces in a single chip targeted atconsumer, industrial, medical, and communication markets. To optimize system powerconsumption, the LPC314x have multiple power domains and a very flexible ClockGeneration Unit (CGU) that provides dynamic clock gating and scaling.
上傳時間： 2013-10-11
上傳用戶：yuchunhai1990
The NXP LPC315x combine an 180 MHz ARM926EJ-S CPU core, High-speed USB 2.0OTG, 192 KB SRAM, NAND flash controller, flexible external bus interface, an integratedaudio codec, Li-ion charger, Real-Time Clock (RTC), and a myriad of serial and parallelinterfaces in a single chip targeted at consumer, industrial, medical, and communicationmarkets. To optimize system power consumption, the LPC315x have multiple powerdomains and a very flexible Clock Generation Unit (CGU) that provides dynamic clockgating and scaling.The LPC315x is implemented as multi-chip module with two side-by-side dies, one fordigital fuctions and one for analog functions, which include a Power Supply Unit (PSU),audio codec, RTC, and Li-ion battery charger.
上傳時間： 2014-01-17
上傳用戶：Altman
Aspen Plus介紹 (物性數據庫) · Aspen Plus ---生產裝置設計、穩態模擬和優化的大型通用流程模擬系統 · Aspen Plus是大型通用流程模擬系統，源于美國能源部七十年代后期在麻省理工學院(MIT)組織的會 戰，開發新型第三代流程模擬軟件。該項目稱為“過程工程的先進系統”(Advanced System for Process Engineering，簡稱ASPEN),并于1981年底完成。1982年為了將其商品化，成立了AspenTech公司，并稱之為Aspen Plus。該軟件經過20多年來不斷地改進、擴充和提高，已先后推出了十多個版本，成為舉世公認的標準大型流程模擬軟件，應用案例數以百萬計。全球各大化工、石化、煉油等過程工業制造企業及著名的工程公司都是Aspen Plus的用戶。 它以嚴格的機理模型和先進的技術贏得廣大用戶的信賴，它具有以下特性： 1. ASPEN PLUS有一個公認的跟蹤記錄，在一個工藝過程的制造的整個生命周期中提供巨大的經濟效益，制造生命周期包括從研究與開發經過工程到生產。 2. ASPEN PLUS使用最新的軟件工程技術通過它的Microsoft Windows圖形界面和交互式客戶-服務器模擬結構使得工程生產力最大。 3. ASPEN PLUS擁有精確模擬范圍廣泛的實際應用所需的工程能力， 這些實際應用包括從煉油到非理想化學系統到含電解質和固體的工藝過程。 4. ASPEN PLUS是AspenTech的集成聰明制造系統技術的一個核心部分， 該技術能在你公司的整個過程工程基本設施范圍內捕獲過程專業知識并充分利用。 在實際應用中，ASPEN PLUS可以幫助工程師解決快速閃蒸計算、設計一個新的工藝過程、查找一個原油加工裝置的故障或者優化一個乙烯全裝置的操作等工程和操作的關鍵問。
上傳時間： 2013-11-16
上傳用戶：我干你啊
