Abstract: This reference design provides design ideas for a cost-effective, low-power liquid-level measurement dataacquisition system (DAS) using a compensated silicon pressure sensor and a high-precision delta-sigma ADC. Thisdocument discusses how to select the compensated silicon pressure sensor, suggest system algorithms, and providenoise analyses. It also describes calibration ideas to improve system performance while also reducing complexity andcost.
上傳時間： 2013-10-08
上傳用戶：sjy1991
本文主要通過介紹PLC通訊的意義和三菱FX系列PLC的四種通訊方式，并重點介紹FX系列PLC與計算機無協議通訊，主要從無協議通訊的硬件、配線、數據寄存器設置、PLC與計算機無協議通訊的指令用法、PLC程序編寫和計算機VB程序的編寫來說明無協議通訊的過程和一般方法。 My dissertation introduces the significance of PLC communications and the four means of communication of Mitsubishi FX’s PLC, And highlights the no protocol communications of FX series PLC and computer, no protocol communications hardware, wiring, Register data set, and the usage of command about no protocol communications, How to write PLC program and computer VB program to illustrate the process of no protocol communications and general method.
上傳時間： 2014-11-29
上傳用戶：Jerry_Chow
The CodeWarrior Development Suite provides access and technical support to amultitude of CodeWarrior products. In this quick start guide, Section 1 explains howto register your CodeWarrior Development Suite. Section 2 explains how to activateand install one of your products. Section 3 describes what you are entitled to withthe purchase of your CodeWarrior Development Suite, and Section 4 discusses theavailable purchase options. Section 5 describes the benefits of maintaining a currenttechnical support contract, and Section 6 tells you how to access support.
標簽： CodeWarrior 開發套件
上傳時間： 2014-03-02
上傳用戶：784533221
Abstract: This application note describes how to create, build, and debug applications targeted for the MAXQ1050 RISC
標簽： MAXQ CrossStudio 1050 30
上傳時間： 2014-08-11
上傳用戶：qwerasdf
This application note provides step-by-step instructions on how to recreate a Tri-Mode Ethernet(TEMAC) performance testing system using the ML405 board and MontaVista Linux 4.0. Thisapplication note shows how to set up a simple EDK Base System Builder system on the ML405Evaluation Platform and run performance tests. The network architecture for the test isdescribed. A system is built and downloaded into the FPGA. A MontaVista Linux kernel isconfigured, built, and downloaded into the ML405 Evaluation Platform. The instructions forobtaining and setting up the software used to perform the measurements, netperf, are given.
上傳時間： 2013-11-11
上傳用戶：saharawalker
飛思卡爾S12處理器培訓講義 In this LAB, we will: Get familiar with CodeWarrior 4.7 IDE; How to work with project wizard; Light the LEDs
上傳時間： 2013-11-13
上傳用戶：LIKE
Abstract: Most hand-held products lack accurate battery-charge monitors ("fuel gauges") because of the misconception that an accurate fuel gauge is difficult to achieve. This article debunks the myths and discusses how to accurately monitor charge at all temperatures, charge and discharge rates, and aging conditions. 無線通信和數據在新一代手機和PDA中的融合為再一次的生產力飛躍創造了條件。。隨之而來的將是經濟的增長和全新的工作方式，在便攜式計算機領域，PC筆記本曾經扮演了類似的開拓者角角。
上傳時間： 2013-10-17
上傳用戶：erkuizhang
Single-Ended and Differential S-Parameters Differential circuits have been important incommunication systems for many years. In the past,differential communication circuits operated at lowfrequencies, where they could be designed andanalyzed using lumped-element models andtechniques. With the frequency of operationincreasing beyond 1GHz, and above 1Gbps fordigital communications, this lumped-elementapproach is no longer valid, because the physicalsize of the circuit approaches the size of awavelength.Distributed models and analysis techniques are nowused instead of lumped-element techniques.Scattering parameters, or S-parameters, have beendeveloped for this purpose [1]. These S-parametersare defined for single-ended networks. S-parameterscan be used to describe differential networks, but astrict definition was not developed until Bockelmanand others addressed this issue [2]. Bockelman’swork also included a study on how to adapt single-ended S-parameters for use with differential circuits[2]. This adaptation, called “mixed-mode S-parameters,” addresses differential and common-mode operation, as well as the conversion betweenthe two modes of operation.This application note will explain the use of single-ended and mixed-mode S-parameters, and the basicconcepts of microwave measurement calibration.
上傳時間： 2014-03-25
上傳用戶：yyyyyyyyyy
Abstract: Most hand-held products lack accurate battery-charge monitors ("fuel gauges") because of the misconception that an accurate fuel gauge is difficult to achieve. This article debunks the myths and discusses how to accurately monitor charge at all temperatures, charge and discharge rates, and aging conditions.
上傳時間： 2014-03-18
上傳用戶：wenwiang
This example provides a description of how to use the USART with hardware flowcontrol and communicate with the Hyperterminal.First, the USART2 sends the TxBuffer to the hyperterminal and still waiting fora string from the hyperterminal that you must enter which must end by '\r'character (keypad ENTER button). Each byte received is retransmitted to theHyperterminal. The string that you have entered is stored in the RxBuffer array. The receivebuffer have a RxBufferSize bytes as maximum. The USART2 is configured as follow: - BaudRate = 115200 baud - Word Length = 8 Bits - One Stop Bit - No parity - Hardware flow control enabled (RTS and CTS signals) - Receive and transmit enabled - USART Clock disabled - USART CPOL: Clock is active low - USART CPHA: Data is captured on the second edge - USART LastBit: The clock pulse of the last data bit is not output to the SCLK pin
上傳時間： 2013-10-31
上傳用戶：yy_cn
