Linear Technology offers a variety of devices that simplifyconverting power from a USB cable, but the LTC®3455represents the highest level of functional integration yet. The LTC3455 seamlessly manages power flowbetween an AC adapter, USB cable and Li-ion battery,while complying with USB power standards, all from a4mm × 4mm QFN package. In addtion, two high efficiencysynchronous buck converters generate low voltage railswhich most USB-powered peripherals require. TheLTC3455 also provides power-on reset signals for themicroprocessor, a Hot SwapTM output for poweringmemory cards as well as an uncommitted Gain blocksuitable for use as a low-battery comparator or an LDOcontroller. The PCB real estate required for the entire USBpower control circuit and two DC/DC converters is only225mm2.
上傳時間： 2013-11-02
上傳用戶：名爵少年
Portable, battery-powered operation of electronic apparatushas become increasingly desirable. Medical, remotedata acquisition, power monitoring and other applicationsare good candidates for batteryoperation. In some circumstances,due to space, power or reliability considerations,it is preferable to operate the circuitry from a single 1.5Vcell. Unfortunately, a 1.5V supply eliminates almost alllinear ICs as design candidates. In fact, the LM10 opamp-reference and the LT®1017/LT1018 comparators arethe only IC Gain blocks fully specifi ed for 1.5V operation.Further complications are presented by the 600mV dropof silicon transistors and diodes. This limitation consumesa substantial portion of available supply range, makingcircuit design diffi cult. Additionally, any circuit designedfor 1.5V operation mustfunction at end-of-life batteryvoltage, typically 1.3V. (See Box Section, “Componentsfor 1.5V Operation.”)
標簽： Circuitry Operation Single Cell
上傳時間： 2013-10-30
上傳用戶：hz07104032
針對煤礦井下調度及緊急救援系統的需求，以DTMF編解碼模塊為核心，設計了具有自動撥號功能的新型電話系統。該系統利用MT8880對DTMF信號的編解碼功能實現一鍵撥號和遠程設置，通過檢測振鈴和忙音信號，完成自動摘機和掛機過程，配合AGC等外圍電路達到話音清晰流暢的效果。 Abstract: To meet the demand for mine scheduling and emergency rescue system， with using DTMF signal codec as the core， a new telephone system was designed with automatic dialing function. In the system， the DTMF signal encoding and decoding function of MT8880 was used to achieve one-touch dialing and remote setting. The circuit detects the ringing and busy signal， and then completes automatic off-hook and hangup. With AGC(Automatic Gain Control) and other peripheral circuits， the voice was regulated to a clear and smooth effect.
上傳時間： 2014-11-18
上傳用戶：ly1994
介紹了以AVR單片機ATmega16為核心，采用前端信號調理電路、程控增益放大器以及波形顯示LCD（GDM12864A）實現的一個簡易示波器。并給出該系統設計的硬件和軟件設計方案。 Abstract: Abstract:This paper introduces an easy digital storage oscilloscope based on the AVR microcontroller ATmega16,especially emphasizes on the software design and the hardware design which contains signal processing circuit,Gain-programmed amplifier circuit and LCD’s interface circuit and so on.
上傳時間： 2013-10-13
上傳用戶：ccccccc
Features• Complete DTMF Receiver• Low power consumption• Internal Gain setting amplifier• Adjustable guard time• Central office quality• Power-down mode• Inhibit mode• Backward compatible withMT8870C/MT8870C-1Applications• Receiver system for British Telecom (BT) orCEPT Spec (MT8870D-1)• Paging systems• Repeater systems/mobile radio• Credit card systems• Remote control• Personal computers• Telephone answering machine
上傳時間： 2013-11-20
上傳用戶：mpquest
NEC 16位MCU參考手冊 The 78K0R/IC3 is a 16-bit single-chip microcontroller that uses a 78K0R CPU core and incorporates peripheral functions, such as ROM/RAM, a multi-function timer, a multi-function serial interface, an A/D converter, a programmable Gain amplifier (PGA), a comparator, a real-time counter, and a watchdog timer.
上傳時間： 2013-11-02
上傳用戶：努力努力再努力
The PCA9541 is a 2-to-1 I2C-bus master selector designed for high reliability dual masterI2C-bus applications where system operation is required, even when one master fails orthe controller card is removed for maintenance. The two masters (for example, primaryand back-up) are located on separate I2C-buses that connect to the same downstreamI2C-bus slave devices. I2C-bus commands are sent by either I2C-bus master and are usedto select one master at a time. Either master at any time can Gain control of the slavedevices if the other master is disabled or removed from the system. The failed master isisolated from the system and will not affect communication between the on-line masterand the slave devices on the downstream I2C-bus.
上傳時間： 2013-10-09
上傳用戶：3294322651
當拿到一張CASE單時，首先得確定的是能用什么母體才能實現此功能，然后才能展開對外圍硬件電路的設計，因此首先得了解每個母體的基本功能及特點，下面大至的介紹一下本公司常用的IC：單芯片解決方案• SN8P1900 系列– 高精度 16-Bit 模數轉換器– 可編程運算放大器 (PGIA)• 信號放大低漂移: 2V• 放大倍數可編程: 1/16/64/128 倍– 升壓- 穩壓調節器 (Charge-Pump Regulator)• 電源輸入: 2.4V ~ 5V• 穩壓輸出: e.g. 3.8V at SN8P1909– 內置液晶驅動電路 (LCD Driver)– 單芯片解決方案 • 耳溫槍 SN8P1909 LQFP 80 Pins• 5000 解析度量測器 SN8P1908 LQFP 64 Pins• 體重計 SN8P1907 SSOP 48 Pins單芯片解決方案• SN8P1820 系列– 精確的12-Bit 模數轉換器– 可編程運算放大器 (PGIA)• Gain Stage One: Low Offset 5V, Gain: 16/32/64/128• Gain Stage One: Low Offset 2mV, Gain: 1.3 ~ 2.5– 升壓- 穩壓調節器• 電源輸入: 2.4V ~ 5V• 穩壓輸出: e.g. 3.8V at SN8P1829– 內置可編程運算放大電路– 內置液晶驅動電路 – 單芯片解決方案 • 電子醫療器 SN8P1829 LQFP 80 Pins 高速/低功耗/高可靠性微控制器• 最新SN8P2000 系列– SN8P2500/2600/2700 系列– 高度抗交流雜訊能力• 標準瞬間電壓脈沖群測試 (EFT): IEC 1000-4-4• 雜訊直接灌入芯片電源輸入端• 只需添加1顆 2.2F/50V 旁路電容• 測試指標穩超 4000V (歐規)– 高可靠性復位電路保證系統正常運行• 支持外部復位和內部上電復位• 內置1.8V 低電壓偵測可靠復位電路• 內置看門狗計時器保證程序跳飛可靠復位– 高抗靜電/栓鎖效應能力– 芯片工作溫度有所提高: -200C ~ 700C 工規芯片溫度： -400C ~ 850C 高速/低功耗/高可靠性微控制器• 最新 SN8P2000 系列– SN8P2500/2600/2700 系列– 1T 精簡指令級結構• 1T: 一個外部振蕩周期執行一條指令• 工作速度可達16 MIPS / 16 MHz Crystal– 工作消耗電流 < 2mA at 1-MIPS/5V– 睡眠模式下消耗電流 < 1A / 5V額外功能• 高速脈寬調制輸出 (PWM)– 8-Bit PWM up to 23 KHz at 12 MHz System Clock– 6-Bit PWM up to 93 KHz at 12 MHz System Clock– 4-Bit PWM up to 375 KHz at 12 MHz System Clock• 內置高速16 MHz RC振蕩器 (SN8P2501A)• 電壓變化喚醒功能• 可編程控制沿觸發/中斷功能– 上升沿 / 下降沿 / 雙沿觸發• 串行編程接口
上傳時間： 2013-10-21
上傳用戶：jiahao131
本文將接續介紹電源與功率電路基板，以及數字電路基板導線設計。寬帶與高頻電路基板導線設計a.輸入阻抗1MHz，平滑性(flatness)50MHz 的OP增幅器電路基板圖26 是由FET 輸入的高速OP 增幅器OPA656 構成的高輸入阻抗OP 增幅電路，它的Gain取決于R1、R2，本電路圖的電路定數為2 倍。此外為改善平滑性特別追加設置可以加大噪訊Gain，抑制Gain-頻率特性高頻領域時峰值的R3。圖26 高輸入阻抗的寬帶OP增幅電路圖27 是高輸入阻抗OP 增幅器的電路基板圖案。降低高速OP 增幅器反相輸入端子與接地之間的浮游容量非常重要，所以本電路的浮游容量設計目標低于0.5pF。如果上述部位附著大浮游容量的話，會成為高頻領域的頻率特性產生峰值的原因，嚴重時頻率甚至會因為feedback 阻抗與浮游容量，造成feedback 信號的位相延遲，最后導致頻率特性產生波動現象。此外高輸入阻抗OP 增幅器輸入部位的浮游容量也逐漸成為問題，圖27 的電路基板圖案的非反相輸入端子部位無full ground設計，如果有外部噪訊干擾之虞時，接地可設計成網格狀(mesh)。圖28 是根據圖26 制成的OP 增幅器Gain－頻率特性測試結果，由圖可知即使接近50MHz頻率特性非常平滑，-3dB cutoff頻率大約是133MHz。
標簽： PCB
上傳時間： 2013-11-09
上傳用戶：z754970244
因為測量系統都用50歐姆, 如非特指, 以下所說的Gain均指功率增益(Power Gain). 但是一般的接收機的輸入輸出并非50歐姆, 因此有必要考慮電壓增益(Voltage Gain).
上傳時間： 2015-01-03
上傳用戶：1318695663
