ArtFormula package contains two nonvisual Delphi component for symbolic expression parsing and EValuation. Provides runtime scripting engine for automating your programs.
標簽： ArtFormula expression component nonvisual
上傳時間： 2013-12-08
上傳用戶：yt1993410
一個針對單片機的網絡通信程序，有經過裁剪的tcp/ip源代碼，硬件平臺由MSP430f149和CS8900構成，實現采集溫度傳感器的溫度，以web形式顯示在上位機上，應用軟件是IAR Embedded Workbench EValuation for MSP430 V4
上傳時間： 2014-01-15
上傳用戶：ynsnjs
FIBPlus is a component suite intended for work with InterBase. It is direct, fast and flexible InterBase connectivity for Delphi, C++ Builder, Ada and Kylix. FIBPlus supports Delphi 5-7, Delphi 2005, Delphi 2006, Delphi 2007, C++ Builder 5-6, C++ Builder 2006, C++ Builder 2007, Kylix 3, gnat-3.15p, gnat2006 GPL, and all versions of InterBase 4.x-7.x, InterBase 2007 and Firebird 1.x-2.x. Using FIBPlus in your applications you do not need to install any additional software except for InterBase Client Software. FIBPlus supports all special InterBase features such as array-fields, event alerters, BLOB-fields, etc. FIBPlus is a native component set and its EValuation versions are distributed partially in sources. Registering FIBPlus you get full sources of components and technical support
標簽： component InterBase intended flexible
上傳時間： 2013-12-01
上傳用戶：xuan‘nian
This SPI-mode SD Card controller is a free SOPC Builder component that can be used in any SOPC Builder system. The included example design runs on the Nios II Embedded EValuation Kit, Cyclone III edition (NEEK).
標簽： SOPC controller component SPI-mode
上傳時間： 2013-12-18
上傳用戶：jing911003
This SPI-mode SD Card controller is a free SOPC Builder component that can be used in any SOPC Builder system. The included example design runs on the Nios II Embedded EValuation Kit, Cyclone III edition (NEEK).
標簽： SOPC controller component SPI-mode
上傳時間： 2017-05-14
上傳用戶：LouieWu
This file is distributed in the hope that it will be useful, but WITHOUT WARRANTY OF ANY KIND. Author(s): Ole Saether DESCRIPTION: This example should be used together with ex2a-tx433.asm. One nRF9E5 EValuation board (receiver) should be programmed with the hex-file generated from assembling this file and the other EValuation board (transmitter) programmed with the hex-file generated from assembling ex2a-tx433.asm. All switches on the DIP-swith S206 on the receiver must be set to the "on" position and all switches on the DIP-swith S205 on the transmitter must be set to the "on" position. When one of the switched SW1-SW4 on the transmitter is pressed the corresponding LED on the receiver is turned on. The functionality is the same as in ex2c-rx.c.
標簽： distributed WARRANTY WITHOUT useful
上傳時間： 2017-05-17
上傳用戶：xieguodong1234
它是SourceForge上的一個開源項目，使用Malib實現實時處理，CSU Face Identification EValuation System進行人臉識別。算法包括：主成份分析(principle components analysis (PCA)),a.k.a eigenfaces算法,混合主成份分析,線性判別分析(PCA+LDA),圖像差分分類器(IIDC),彈性圖像匹配算法(EBGM)等等 Malic is realtime face recognition system that based on Malib and CSU Face Identification EValuation System (csuFaceIdEval). Uses Malib library for realtime image processing and some of csuFaceIdEval for face recognition.
標簽： SourceForge 開源 項目
上傳時間： 2014-01-21
上傳用戶：sz_hjbf
The goal of this thesis is the development of traffic engineering rules for cellular packet radio networks based on GPRS and EDGE. They are based on traffic models for typical mobile applications. Load generators, representing these traffic models, are developed and integrated into a simulation environment with the prototypical implementation of the EGPRS protocols and models for the radio channel, which were also developed in the framework of this thesis. With this simulation tool a comprehensive performance EValuation is carried out that leads to the traffic engineering rules.
標簽： development engineering cellular traffic
上傳時間： 2014-01-11
上傳用戶：Miyuki
These codes require an ASCII input file interp.dat of the following form: N: Number of Polynomial Interpolation Points (Small) First Sample (x1,y1) Second Sample (x2,y2) ... Nth Sample (xN,yN) N1: Number of Error EValuation Points (Large) First Sample (x1,y1) Second Sample (x2,y2) ... N1th Sample (xN1,yN1)
標簽： Polynomia following require Number
上傳時間： 2017-09-21
上傳用戶：許小華
A large body of computer-aided techniques has been developed in recent years to assist in the process of modeling, analyzing, and designing communication systems . These computer-aided techniques fall into two categories: formula-based approaches, where the computer is used to evaluate complex formulas, and simulation-based approaches, where the computer is used to simulate the waveforms or signals that flow through the system. The second approach, which involves “waveform”-level simulation (and often incorporates analytical techniques), is the subject of this book. Since performance EValuation and trade off studies are the central issues in the analysis and design of communication systems, we will focus on the use of simulation for evaluating the performance of analog and digital communication systems with the emphasis on digitalcommunication systems.
標簽： computer-aided techniques developed assist
上傳時間： 2014-01-01
上傳用戶：541657925
