Designing read/write device (RWD) units for industrial RF-Identification
applications is strongly facilitated by the NXP Semiconductors HITAG
Reader Chip HTRC110. All needed function blocks, like the antenna
driver, modulator Demodulator and antenna diagnosis unit, are integrated
in the HTRC110. Therefore only a minimum number of additional passive
components are required for a complete RWD.
This Application Note describes how to design an industrial
RF-Identification system with the HTRC110. The major focus is
dimensioning of the antenna, all other external components including
clock and power supply, as well as the demodulation principle and its
implementatio
為了在CDMA系統中更好地應用QDPSK數字調制方式，在分析四相相對移相（QDPSK)信號調制解調原理的基礎上，設計了一種QDPSK調制解調電路，它包括串并轉換、差分編碼、四相載波產生和選相、相干解調、差分譯碼和并串轉換電路。在MAX+PLUSⅡ軟件平臺上，進行了編譯和波形仿真。綜合后下載到復雜可編程邏輯器件EPM7128SLC84-15中，測試結果表明，調制電路能正確選相，解調電路輸出數據與QDPSK調制輸入數據完全一致，達到了預期的設計要求。
Abstract:
In order to realize the better application of digital modulation mode QDPSK in the CDMA system， a sort of QDPSK modulation-demodulation circuit was designed based on the analysis of QDPSK signal modulation-demodulation principles. It included serial/parallel conversion circuit, differential encoding circuit, four-phase carrier wave produced and phase chosen circuit, coherent demodulation circuit, difference decoding circuit and parallel/serial conversion circuit. And it was compiled and simulated on the MAX+PLUSⅡ software platform,and downloaded into the CPLD of EPM7128SLC84-15.The test result shows that the modulation circuit can exactly choose the phase，and the output data of the Demodulator circuit is the same as the input data of the QDPSK modulate. The circuit achieves the prospective requirement of the design.
為了在CDMA系統中更好地應用QDPSK數字調制方式，在分析四相相對移相（QDPSK)信號調制解調原理的基礎上，設計了一種QDPSK調制解調電路，它包括串并轉換、差分編碼、四相載波產生和選相、相干解調、差分譯碼和并串轉換電路。在MAX+PLUSⅡ軟件平臺上，進行了編譯和波形仿真。綜合后下載到復雜可編程邏輯器件EPM7128SLC84-15中，測試結果表明，調制電路能正確選相，解調電路輸出數據與QDPSK調制輸入數據完全一致，達到了預期的設計要求。
Abstract:
In order to realize the better application of digital modulation mode QDPSK in the CDMA system， a sort of QDPSK modulation-demodulation circuit was designed based on the analysis of QDPSK signal modulation-demodulation principles. It included serial/parallel conversion circuit, differential encoding circuit, four-phase carrier wave produced and phase chosen circuit, coherent demodulation circuit, difference decoding circuit and parallel/serial conversion circuit. And it was compiled and simulated on the MAX+PLUSⅡ software platform,and downloaded into the CPLD of EPM7128SLC84-15.The test result shows that the modulation circuit can exactly choose the phase，and the output data of the Demodulator circuit is the same as the input data of the QDPSK modulate. The circuit achieves the prospective requirement of the design.
This packet is a IS-95 baseband simulation for 1 data channel of 9.6 KBps rate. The simulation is written for static channel and AWGN noise.
The packet include:
1) Packet Builder (Viterbi Encoding, Interleaver, PN generation)
2) Modulator (RRC filter)
3) Demodulator (Matched Filter, RAKE receiver)
4) Receiver (HD or SD) (Deinterleaver, Viterbi Decoder).
You should run "Simulation.m" function that include all modules.
his packet is a IS-95 baseband simulation for 1 data channel of 9.6 KBps rate.
The simulation is written for static channel and AWGN noise. The packet include:
1) Packet Builder (Viterbi Encoding, Interleaver, PN generation)
2) Modulator (RRC filter)
3) Demodulator (Matched Filter, RAKE receiver)
4) Receiver (HD or SD) (Deinterleaver, Viterbi Decoder).
You should run "Simulation.m" function that include all modules.
This paper investigates the design of joint frequency
offset and carrier phase estimation of a multi-frequency time division
multiple access (MF-TDMA) Demodulator that is applied to
a digital video broadcasting—return channel system via satellite
(DVB-RCS). The proposed joint estimation algorithm is based on
the interpolation technique for two correlation values in the frequency
and phase domains. This simple interpolation technique
can significantly improve frequency and phase resolution capabilities
of the proposed technique without increasing the number of
the correlation values. In addition, the overall block diagram of a
digital communications receiver for DVB-RCS is presented, which
was designed using the proposed estimation algorithms.
Index Terms—Carrier phase estimation, DVB-RCS, frequency
offset estimation, interpolation, joint estimation, MF-TDMA.
This packet is a IS-95 baseband simulation for 1 data channel of 9.6 KBps rate.
The simulation is written for static channel and AWGN noise. The packet include:
1) Packet Builder (Viterbi Encoding, Interleaver, PN generation)
2) Modulator (RRC filter)
3) Demodulator (Matched Filter, RAKE receiver)
4) Receiver (HD or SD) (Deinterleaver, Viterbi Decoder).
