Demonstration circuit 1562A is an engineering toolto design and evaluate the LTC699X-X family ofTimerBlox circuits. The center section of the boardcontains a pre-configured TimerBlox function.DC1562A comes in twelve timing function variationsas outlined in Table 1.Surrounding the center board is a ”playground”prototyping area. The prototyping area has padsfor Dip-8, S8, MS8, or S6 packages with breadboarding connections to each pin and two convenientpower buses and ground bus surrounding theentire area. This area is for conditioning signals tocontrol the timer function and for adding loads controlled in time.
標簽： 6994 LTC PCB 參考設計
上傳時間： 2013-10-18
上傳用戶：如果你也聽說
Analog Inputs and Outputs in an S7 PLC are represented in the PLC as a 16-bit integer. Over the nominal span of the analog input or output, the value of this integer will range between - 27648 and +27648. However, it is easier to use the analog values if they are scaled to the same units and ranges as the process being controlled. This applications tip describes methods for scaling analog values to and from engineering units.
標簽： 300 PLC 西門子 模擬量
上傳時間： 2013-11-17
上傳用戶：3294322651
為了提高傳統溫度控制系統的性能，將PID控制理論與嵌入式系統相結合，采用瑞薩電子公司的H8S/2166作為核心處理器，AD公司的AD7705以及熱敏電阻溫度傳感器作為溫度檢測單元，利用4×6小鍵盤、LCD顯示器和S1D13305液晶控制器達到良好的人機交互，設計出了一個應用于化工領域的嵌入式實時溫度控制系統。相比于傳統溫度控制系統，該系統提供了更強的計算能力和可擴展能力，采用增量PID控制算法實現復雜控制。通過實驗，該系統能達到0.1 ℃的溫度控制精度以及小于120 s的溫度穩定時間。 Abstract: In order to improve the performance of conventional temperature control system， combining PID control theory with embedded systems， using the Renesas Electronics Corp. H8S/2166 micro-controller as a core processors， AD7705 and thermistor temperature sensor as a temperature detection unit and 4×6 small keyboard， LCD and S1D13305 LCD controller as a good human-computer interaction， this paper designed an embedded real-time temperature control system which is applied in chemical industry. Compared with conventional temperature control system， this system provides more computing power and extensibility， and adopts PID control algorithm for complex control. Through the experiment， the system can reach temperature control accuracy of 0.1 ℃ and temperature stabilization time of less than 120 seconds.
標簽： 瑞薩電子 微控制器 溫度控制 系統設計
上傳時間： 2014-12-26
上傳用戶：003030
為了有效地提升鉛酸蓄電池的使用壽命，同時實現對充電過程的監控，設計出一種用單片機控制的36 V鉛酸蓄電池充電電源。本電路采用反激式拓?fù)洌B續電流工作模式，電源管理IC設計在電源的副邊，由ELAN公司的EM78P258N單片機模擬，是用可編程器件模擬電源管理IC，實現智能電源低成本化的一次成功嘗試，通過對單片機的軟件設計實現了充電電源的狀態顯示、充電時間控制、報警、過溫保護、過壓保護、過流保護等功能。本充電器真正的實現了鉛酸蓄電池的三段式充電過程，其最高輸出功率可達90 W，效率約85%，成本不到20元，具有很高的市場競爭力。 Abstract: In order to extend the life of lead-acid battery efficiently and supervise the charging process meanwhile， a 36V lead-acid battery charge powe supply controlled by microcontroller is designed. The charger is flyback switching power supply and works in CCM mode. A EM78P258N microcontroller made by ELAN microelectronics corporation is used as power management IC which is designed at the secondary circuit. The project is a successful attempt to low-cost intelligent power used microcontroller simulating power management IC. The charger also has the functions of the status reveal， charge time control， alarming， thermal protect， current limit and overvoltage protect by the software design. The circuit actually implements the three-step charge process， whose power is up to 90W and whose efficiency can get 85%. The net cost of this charger is less than 20 RMB， so that the charger is of powerful market competitiveness.
標簽： 單片機控制 充電電源 鉛酸蓄電池
上傳時間： 2013-11-16
上傳用戶：cepsypeng
為解決當前計算機串行通訊接口只有USB，難以滿足舊型號設備或某些單片機要求RS232通訊的問題，設計出兩款RS232/USB電路。采用CH341A與MAX223集成電路芯片構建標準9線RS232/USB通用接口轉換器，無需編程。采用CH341A與PIC16F877A構建單片機與計算機之間的USB通訊電路，軟件遵循RS232通訊協議，硬件進行電平轉換。實際使用表明，這兩款產品與計算機端Windows 操作系統下的串口應用程序完全兼容，且通訊過程中無握手失敗現象。 Abstract: To solve the problem that current computer serial communication only with USB interface can not satisfy with the old type equipments or MCU to communicate with RS232， two kinds of RS232/USB circuit were designed.CH341A and MAX223 integrated circuit chips were used to create a standard 9-line RS232/USB universal interface convertor without programme. CH341A and PIC16F877A chips were adopted to build the USB communication circuit between computers and MCU. The software follows RS232 communication protocol， and the hardware converts electrical levels. Actual practices indicate that the two manufactures are compatible with serial application program of Windows operation system completely，and get avoid of handshake lost.
上傳時間： 2013-11-03
上傳用戶：siying
以C8051F020為核心處理器，設計無線傳感器網絡數據采集系統。系統采用SZ05-ADV型無線通訊模塊組建Zigbee無線網絡，結合嵌入式系統的軟硬件技術，完成終端節點的8路傳感器信號的數據采集。現場8路信號通過前端處理后，分別送入C8051F020的12位A/D轉換器進行轉換。經過精確處理、存儲后的現場數據，通過Zigbee無線網絡傳送到上位機，系統可達到汽車試驗中無線測試的目的。 Abstract: This paper designs a wireless sensor network system for data acquisition with C8051F020 as core processors.The system used SZ05-ADV wireless communication module，set up a Zigbee wireless network， combined with hardware and software technologies of embedded systems，completed the end-node 8-locale sensor signal data acquisition.Eight locale signals were sent separately into the 12-bit ADC of C8051F020 for conversion through front treatment.After accurate processing and storage，the locale data was transmitted to the host computer through Zigbee wireless.The system achieves the purpose of wireless testing in vehicle trial.
標簽： C8051F020 Zigbee 汽車測試 系統設計
上傳時間： 2013-11-23
上傳用戶：dsgkjgkjg
生活中許多目標的高度和水平距離需要進行測量。目前主要的測量方法，仍以傳統的皮尺丈量為主，測量效率不高，有時還很不方便，沒有技術成熟的數字式測高測距產品。以基本的數學方法為理論依據，利用遙控小車做為載體，采用角度傳感器測量角度、霍爾傳感器測量水平距離等，通過單片機LM3S615進行數據計算，實現了對待測目標物體的高度、水平距離等數據的快速、精確和數字式的測量，高度測量精度可達99.06%，水平測量精度則可達98.06%。 Abstract: In our lives， the height and horizontal distance of some goals are needed to be measured. Because the currently used methods are still traditional tape-based measuring methods， and the measuring efficiency is low and inconvenient so some kinds of digital and portable measuring methods or instruments are needed. Based on the basic math theory， this paper designed and manufactured a portable， digital and remote controlled measuring mobile small vehicle， which assembled with angle measuring sensor for angle measurement and Hall sensor for horizontal distance measuring. MCU LM3S615 calculated the height and horizontal distance data gotten from these sensors. The measuring process is simple， the measuring results are more accurate and the measuring efficiency is higher than traditional measure instruments. The accuracy of height and distance measurement can reach 99.06% and 98.06%.
標簽： ARM 單片機 自動
上傳時間： 2013-10-30
上傳用戶：jackandlee
提出一種基于凌陽單片機的步進電機加減速的控制方法。采用凌陽科技推出的16位結構工控單片機SPMC75F2413A為控制器，由Allegro公司生產的兩相步進電機專用驅動器件SLA7042M構成步進電機的驅動電路，在傳統的3段直線加減速控制算法基礎上增加至7段S形曲線加減速過程，控制步進電機的啟動和停止。實驗結果表明，該控制方法克服了直線加減速中不連續、易造成系統沖擊的問題，整個系統實現柔性控制，電機啟動、停止連續性能提高30%。 Abstract: The method of controlled stepping motor is referred based on SPMC75F2413A MCU， which adopts the 16 knots SPMC75F2413A MCU as the controller. The special-purpose actuation chip SLA7042M of two stepping motor produced by Allegro Corporation constituted to actuation electric circuit. The purpose of increasing to seven section of S shape curve based on the traditional three sections of straight line is to control the start and stop process of stepping motor. The experimental results show that the control method solves easy to pull-out and overshot problems. The overall system realizes flexible control， and the performance of motor start or stop continuity is increased 30%
標簽： 凌陽單片機 步進電機 減 控制方法
上傳時間： 2013-12-08
上傳用戶：jiangfire
設計一種基于ATmega16L單片機的溫度控制系統，闡述該系統的軟硬件設計方案。采用模塊化設計方法，利用增量式PID算法使被控對象的溫度值趨于給定值。實驗結果表明該系統具有良好的檢測和控制功能。 Abstract: This paper designs a temperature control system based on ATmega16L，describes the hardware and software de－sign scheme of the system，adopts the modularized design method and utilizes the incremental PID algorithm to realize the temperature of controlled device incline to the given value.The experiment result indicates that the system has good detec－tion and control function
標簽： ATmega 16L 16 單片機
上傳時間： 2013-10-09
上傳用戶：stvnash
為提高溫度測量效率，降低系統的成本，擴展傳輸距離，設計出一種新型溫度采集系統。單片機通過控制具有單總線方式的溫度傳感器DS18B20實現對溫度的測量，同時單片機通過控制具有單總線方式300～450MHz頻率范圍內的MAX7044與MAX7033無線發射與接收芯片實現溫度數據的無線傳輸。與傳統溫度采集系統相比，該系統利用單總線方式連接，采用無線傳輸方式實現遠距離通信，易于系統的集成與擴展。實驗結果表明，該系統結構簡單、方便移植，能夠同時實現多達上百點溫度的測量與500m范圍的傳輸。 Abstract: To improve the temperature measurement efficiency and reduce system cost,expansion of transmission distance,a new type of temperature acquisition system is designed.Microcontroller controlled temperature sensor DS18B20which has a single-bus achieves temperature measurement,while microcontroller by controlled the MAX7044and MAX7033chip with a single-bus and having300~450MHz radiofrequency to achieve the wireless transmission of temperature data.Compared with conventional temperature acquisition system,the system uses single-bus connected,and uses wireless transmission means to achieve long-distance communications,easy-to-system integration and expansion.The experimental results show that the system is simple,convenient transplantation,and can be implemented in as many as a hundred-point temperature measure-ment and the transmission range of500meters.
標簽： 單總線 無線溫度 采集 系統設計
上傳時間： 2013-10-29
上傳用戶：515414293
蟲蟲下載站版權所有 京ICP備2021023401號-1
