為深入了解基于UC3854A控制的PFC變換器中的動力學特性，研究系統參數變化對變換器中分岔現象的影響，在建立Boost PFC變換器雙閉環數學模型的基礎上，用Matlab軟件對變換器中慢時標分岔及混沌等不穩定現象進行了仿真。在對PFC變換器中慢時標分岔現象仿真的基礎上，分析了系統參數變化對分岔點的影響，并進行了仿真驗證。仿真結果清晰地顯示了輸入整流電壓的幅值變化對系統分岔點的影響。 Abstract: In order to better understand the dynamics characteristic of power factor correction converter based on UC3854A， and make the way that parameters change influences the bifurcation phenomena of the system clearly. The math model of the two closed loop circuits to the Boost PFC （Power Factor Correction） converter controller was built. Then， with the help of Matlab， the simulation for nonlinear phenomena such as chaos and slow-scale bifurcation in the PFC converter was made. Finally the factors that have influence to the phenomenon of bifurcation under slow-scale in PFC converter were analyzed. The simulation results clearly show the parameters change influences the bifurcation point of the system.
上傳時間： 2013-10-17
上傳用戶：杜瑩12345
以AVR單片機ATmega8和USB接口器件PDIUSBD12為核心，基于標準的USB1.1協議，設計一種通用USB接口模塊，以滿足嵌入式系統中對USB接口的需求。對模塊的硬件電路或單片機固件程序的硬件接口層稍加修改即可用于其他各種微處理器。該模塊可為各種嵌入式系統增加USB接口,實現與USB主機系統通信。 Abstract: Based on AVR microcontroller ATmega8 and USB interface chip PDIUSBD12, a general USB interface module is designed according to USB1.1 protocol for various requirements of embedded systems. Only with few modifications in circuit or hardware abstract layer of firmware, the module can be used on many types of microprocessors. All kinds of embedded systems can realize high speed and stable communication with USB host systems, owing to the facility of this module.
上傳時間： 2014-01-08
上傳用戶：趙云興
針對材料試驗機等設備中要求測量或控制材料拉伸或壓縮的位移，一般采用光電軸角編碼器檢測位置信號，輸出正交編碼脈沖信號。若采用其他方法檢測位置信號，必然導致電路設計復雜，可靠性降低。因此，提出一種基于LS7266R1的電子式萬能材料試驗機設計方案。給出了試驗機中的控制器工作原理，LS7266R1與單片機的接口硬件設計，以及主程序軟件流程圖。巧妙地把力量傳感器，位移傳感器等機械運動狀態的壓力或拉力以及位置坐標，變成了電壓信號和電脈沖數字信號，供A/D測量和LS7266R1計數，從而實現了獨立完成材料試驗控制或通過PC機串口命令完成材料試驗控制。 Abstract: Aiming at the requirement that the displacement of the tension and compression always be tested and controlled in the equipement such as material testing machine. The position signal was tested by photoelectric axial angle coder. Therefore， the paper proposes the design of electronic universal testing machine design based on LS7266R1. If the position signal detected by other methods， will inevitably lead to the circuit design complexity， reliability decreased. The work theory of the controller， the hardware interface design between LS7266R1 and single chip， and the flow chart of main program， are presented in this paper. The signal of the compression or tension power and displacement at working， which tested by power sensor and displacement sensor especially， is changed into electric voltage and electric pulse numerical signals. And these signals can be tested by A/D and counted by LS7266R1. Finally the test of the material properties can be controlled by itself， or controlled by the COM command of PC.
上傳時間： 2013-11-02
上傳用戶：yl1140vista
介紹一種應用于長城賽弗SUV汽車后門車窗多功能控制器，能實現對電動玻璃車窗、車窗雨刮器、噴水器以及電加熱除霜器等控制。介紹了基于NXP P89LPC922單片機多功能汽車后車窗控制器的控制功能、硬件電路原理和軟件設計方法。 Abstract: This paper presents a multipurpose automotive rear windows controller for CHANGCHENG SAFE SUV.The controller can control rear power-operated window,rear wiping,washing water pump and rear defroster of the windows. In this paper, it is introduced in detail that the functions and the design of the circuit and program of the controller based on NXP P89LPC922 MCU.
上傳時間： 2013-11-13
上傳用戶：z754970244
介紹了基于單片機C8051F020的通用串口適配器的設計與實現方法，即由單片機控制的智能化一對多口收發信號轉換器。通過采用C51對單片機進行編程，控制與RS-232（標準RS-232電平）、RS232(TTL電平)、RS-422接口的數據通信；采用C++ Builder作為開發平臺，通過RS-232接口實現上位機對適配器各個通信端口的控制。 Abstract: Design and realization of a universal serial port adapter based on the MCU C8051F020 are introduced.The adapter is an intelligent one-to-more receiving and transmitting signal converter controlled by the MCU. By programming the MCU with the language C51,MCU control data communication between the MCU and RS-232(RS-232 level),RS-232(TTL level),RS-422 port; Using C++ Builder as the development plane, by one RS232 port, the upper PC can control each of the communication port of the adapter.
上傳時間： 2013-11-19
上傳用戶：hebanlian
介紹一種以MSP430單片機為基礎的智能頻率測量系統，采用硬件邏輯與軟件指令相結合的方式控制閘門，實現0 MHz~10 MHz范圍內無檔切換的等精度測量。 Abstract: An intelligent frequency measurement system based on MSP430 singlechip is introduced. The system uses a way that can combine hardware logic and software instructions to contronl the strobe ,and completes the functions of equal precision in the range of 0MHz~10MHz without shifting
上傳時間： 2013-10-28
上傳用戶：dbs012280
介紹一種基于單片機的多路溫度采集及監控系統，能夠測量6路溫度信號，具有計算機聯網功能，各測量點可以單獨監控和設置，可根據用戶的需求自動控制。測量溫度范圍為-10 ℃～200 ℃，控制方式采用模擬量調壓模式。該系統具有控制精度高、沖擊小等特點。 Abstract: A temperature collecting and surveillance-controlling system based on sing-chip microcomputer is introduced. It can measure 6 channel signal of the temperature,and it has a function of network connection.The temperature measure points can be monitored and located, it can be controlled automatic according to user’s demand.The temperature range is -10℃ to 200℃.The model of control is adjustable voltage with simulation. It features high precision and little impact.
上傳時間： 2013-10-23
上傳用戶：bjgaofei
出了一種利用ATmega8單片機對ISD2500系列語音芯片進行控制的智能語音系統，此系統使用靈活，易于功能升級，具有良好的應用前景。提供了硬件連接電路和關鍵源程序。 Abstract: An intelligent voice system using ISD2500 series voice chips based on ATmega8 MCU is described.This system is flexible and easy to upgrade for users,and it has pretty good using foreground. The circuit diagram and the key program are also provided.
上傳時間： 2014-01-22
上傳用戶：Artemis
為降低成本和解決現有膜片鉗放大器系統中PC機的干擾問題，研究了一種基于單片機的膜片鉗放大器小系統。該系統采用ADI公司生產的ADuC841作為控制核心，并且配置相應的液晶顯示模塊LCM3202401。模擬電路部分采用高輸入阻抗的AD8627實現微電流信號的采集，并由后級電路進行信號的放大和電阻電容的補償。它具有硬件電路簡單、體積小、使用方便的特點。既可以單獨作為小系統實現采集和顯示，也可以通過紅外方式和PC機進行通訊，在PC機上進行信號的處理。 Abstract: In order to reduce cost and resolve the interferential problem with PC in existing patch clamp amplifiers, a small patch clamp amplifier system design based on microcontroller is studied. It adopts a new high performance microconverter ADuC841 by the ADI as the control core in the system, configuring a liquid crystal module LCM3202401. In the analog circuit, AD8627 with high input impedance is used to detect the low current，signal magnification, as well as resistance and capacitance compensation are accomplished by subsequent circuits. It has the advantage of simple hardware circuit design, small volume and convenient operation. It can either be used as an independent system to measure and show signal detected or transmit to PC by infrared ray.
上傳時間： 2013-11-06
上傳用戶：yy_cn
在介紹基于MSP430單片機的指紋保險柜工作原理的基礎上，從系統軟件設計的角度出發，詳細介紹了指紋保險柜軟件的總體分析過程、程序結構的設計以及代碼的編寫，給出了按鍵管理流程和部分源代碼。 Abstract: On basis of the operating principle of MSP430 microcontroller-based fingerprint safe,the general analyzing process,program designing and code compiling of the fingerprint safe software are introduced mainly,and the key-press flows chart and some codes according to the system software designing are put forward.
上傳時間： 2014-12-27
上傳用戶：gaojiao1999
