The PW2601 is a charger front-end integrated circuit designed to provide protection to Li-ionbatteries from failures of charging circuitry. The device monitors the input voltage, battery voltageand the charging current to make sure all three parameters are operated in normal range. Thedevice will switch off internal MOSFET to disconnect IN to OUT to protect load when any of inputvoltage, output current exceeds the threshold. The Over temperature protection (OTP) functionmonitors chip temperature to protect the device. The PW2601 also can protect the system’sbattery from being over charged by monitors the battery voltage continuously. The deviceoperates like a linear regulator, maintaining a 5.1V output with input voltages up to the input overvoltage threshold.The PW2601 is available in DFN-2x2-8L package. Standard products are Pb-free and Halogenfree
基于藥物治療在臨床治療中的重要性,分析目前服藥提醒裝置存在的不足,以STM32F103VET6單片機為控制核心,設計了一種多功能電子藥箱。該系統包括顯示模塊、語音模塊和數據存儲模塊。顯示模塊通過觸摸屏電路和LED指示燈電路,與語音模塊相配合,實現了服藥提醒及指導的功能;數據存儲模塊通過EEPROM存儲電路,能夠實現掉電時服藥信息不丟失的功能。并且為了實現電子藥箱的智能化控制,開發了手機APP,兩者之間可通過WIFI進行數據通信。經測試,該藥箱能夠有效地幫助慢性病患者按時、定量、正確服用藥物,適合在家庭中推廣使用,具有較高的應用價值和實踐意義。Based on the importance of drug therapy in clinical treatment, this paper analyzes the shortcomings of current drug reminder devices, and designs a multi-function electronic medicine box with STM32 F103 VET6 microcontroller as the control core. The system includes a display module, a voice module, and a data storage module. The display module cooperates with the voice module through the touch screen circuit and the LED indicator circuit to realize the function of reminding and guiding the medicine;the data storage module can realize the function of not losing the medication information when the power is off through the EEPROM storage circuit.After testing, the medicine box can effectively help chronic diseases patients to take drugs on time, in a quantitative and correct manner,and is suitable for popularization in the family, and has high application value and practical significance.
數字示波器功能強大,使用方便,但是價格相對昂貴。本文以Ti的MSP430F5529為主控器,以Altera公司的EP2C5T144C8 FPGA器件為邏輯控制部件設計數字示波器。模擬信號經程控放大、整形電路后形成方波信號送至FPGA測頻,根據頻率值選擇采用片上及片外高速AD分段采樣。FPGA控制片外AD采樣并將數據輸入到FIFO模塊中緩存,由單片機進行頻譜分析。測試表明:簡易示波器可以實現自動選檔、多采樣率采樣、高精度測頻及頻譜分析等功能。Digital oscilloscope is powerful and easy to use, but also expensive. The research group designed a low-cost digital oscilloscope, the chip of MSP430F5529 of TI is chosen as the main controller and the device of EP2C5T144C8 of Altera company is used as the logic control unit. Analog signal enter the programmable amplifier circuit, shaping circuit and other pre-processing circuit. The shaped rectangular wave signal is sent to FPGA for measure the frequency. According to the frequency value to select AD on-chip or off-chip high-speed AD for sampling. FPGA controls the off-chip AD sampling and buffers AD data by FIFO module. The single chip microcomputer receives the data, and do FFT for spectrum analysis. The test shows that the simple oscilloscope can realize automatic gain selection, sampling at different sampling rates, high precision frequency measurement and spectrum analysis.
設計功率MOSFET驅動電路時需重點考慮寄生參數對電路的影響。米勒電容作為MOSFET器件的一項重要參數,在驅動電路的設計時需要重點關注。重點觀察了MOSFET的開通和關斷過程中柵極電壓、漏源極電壓和漏源極電流的變化過程,并分析了米勒電容、寄生電感等寄生參數對漏源極電壓和漏源極電流的影響。分析了柵極電壓在米勒平臺附近產生振蕩的原因,并提出了抑制措施,對功率MOSFET的驅動設計具有一定的指導意義。When designing the drive circuit of power MOSFET,the influence of parasitic parameters on the circuit should be concerned.As an important parameter of MOSFET device,Miller capacitance should be considered in the design of drive circuit.The variation of gate voltage,drain source voltage and drain source current during the turn-on and turn-off of MOSFET were observed.The influences of parasitic parameters such as Miller capacitance and parasitic inductance on drain source voltage and drain source current were analyzed.The reasons of gate voltage oscillation nearby Miller plateau were analyzed,and the restraining measures were put forward.This research was instructive for the drive design of power MOSFET.
