All inputs of the C16x family have Schmitt-Trigger input characteristics. These Schmitt-Triggers are intended to always provide proper internal low and high levels, even if anundefined voltage level (between TTL-VIL and TTL-VIH) is externally applied to the pin.The hysteresis of these inputs, however, is very small, and can not be properly used in anapplication to suppress signal noise, and to shape slow rising/falling input transitions.Thus, it must be taken care that rising/falling input signals pass the undefined area of theTTL-specification between VIL and VIH with a sufficient rise/fall time, as generally usualand specified for TTL components (e.g. 74LS series: gates 1V/us, clock inputs 20V/us).The effect of the implemented Schmitt-Trigger is that even if the input signal remains inthe undefined area, well defined low/high levels are generated internally. Note that allinput signals are evaluated at specific sample points (depending on the input and theperipheral function connected to it), at that signal transitions are detected if twoconsecutive samples show different levels. Thus, only the current level of an input signalat these sample points is relevant, that means, the necessary rise/fall times of the inputsignal is only dependant on the sample rate, that is the distance in time between twoconsecutive evaluation time points. If an input signal, for instance, is sampled throughsoftware every 10us, it is irrelevant, which input level would be seen between thesamples. Thus, it would be allowable for the signal to take 10us to pass through theundefined area. Due to the sample rate of 10us, it is assured that only one sample canoccur while the signal is within the undefined area, and no incorrect transition will bedetected. For inputs which are connected to a peripheral function, e.g. capture inputs, thesample rate is determined by the clock cycle of the peripheral unit. In the case of theCAPCOM unit this means a sample rate of 400ns @ 20MHz CPU clock. This requiresinput signals to pass through the undefined area within these 400ns in order to avoidmultiple capture events.For input signals, which do not provide the required rise/fall times, external circuitry mustbe used to shape the signal transitions.In the attached diagram, the effect of the sample rate is shown. The numbers 1 to 5 in thediagram represent possible sample points. Waveform a) shows the result if the inputsignal transition time through the undefined TTL-level area is less than the time distancebetween the sample points (sampling at 1, 2, 3, and 4). Waveform b) can be the result ifthe sampling is performed more than once within the undefined area (sampling at 1, 2, 5,3, and 4).Sample points:1. Evaluation of the signal clearly results in a low level2. Either a low or a high level can be sampled here. If low is sampled, no transition willbe detected. If the sample results in a high level, a transition is detected, and anappropriate action (e.g. capture) might take place.3. Evaluation here clearly results in a high level. If the previous sample 2) had alreadydetected a high, there is no change. If the previous sample 2) showed a low, atransition from low to high is detected now.
標簽： Signal Input Fall Rise
上傳時間： 2013-10-23
上傳用戶：copu
All inputs of the C16x family have Schmitt-Trigger input characteristics. These Schmitt-Triggers are intended to always provide proper internal low and high levels, even if anundefined voltage level (between TTL-VIL and TTL-VIH) is externally applied to the pin.The hysteresis of these inputs, however, is very small, and can not be properly used in anapplication to suppress signal noise, and to shape slow rising/falling input transitions.Thus, it must be taken care that rising/falling input signals pass the undefined area of theTTL-specification between VIL and VIH with a sufficient rise/fall time, as generally usualand specified for TTL components (e.g. 74LS series: gates 1V/us, clock inputs 20V/us).The effect of the implemented Schmitt-Trigger is that even if the input signal remains inthe undefined area, well defined low/high levels are generated internally. Note that allinput signals are evaluated at specific sample points (depending on the input and theperipheral function connected to it), at that signal transitions are detected if twoconsecutive samples show different levels. Thus, only the current level of an input signalat these sample points is relevant, that means, the necessary rise/fall times of the inputsignal is only dependant on the sample rate, that is the distance in time between twoconsecutive evaluation time points. If an input signal, for instance, is sampled throughsoftware every 10us, it is irrelevant, which input level would be seen between thesamples. Thus, it would be allowable for the signal to take 10us to pass through theundefined area. Due to the sample rate of 10us, it is assured that only one sample canoccur while the signal is within the undefined area, and no incorrect transition will bedetected. For inputs which are connected to a peripheral function, e.g. capture inputs, thesample rate is determined by the clock cycle of the peripheral unit. In the case of theCAPCOM unit this means a sample rate of 400ns @ 20MHz CPU clock. This requiresinput signals to pass through the undefined area within these 400ns in order to avoidmultiple capture events.
上傳時間： 2014-04-02
上傳用戶：han_zh
I2C interface, is a very powerful tool for system designers. Theintegrated protocols allow systems to be completely software defined.Software development time of different products can be reduced byassembling a library of reusable software modules. In addition, themultimaster capability allows rapid testing and alignment ofend-products via external connections to an assembly-line computer.The mask programmable 87LPC76X and its EPROM version, the87LPC76X, can operate as a master or a slave device on the I2Csmall area network. In addition to the efficient interface to thededicated function ICs in the I2C family, the on-board interfacefacilities I/O and RAM expansion, access to EEPROM andprocessor-to-processor communications.
標簽： microcontro Using 76X LPC
上傳時間： 2013-12-30
上傳用戶：Artemis
The MC68HC05K0 is a low cost, low pin countsingle chip microcomputer with 504 bytes of userROM and 32 bytes of RAM. The MC68HC05K0 isa member of the 68HC05K series of devices whichare available in 16-pin DIL or SOIC packages.It uses the same CPU as the other devices in the68HC05 family and has the same instructions andregisters. Additionally, the device has a 15-stagemulti-function timer and 10 general purposebi-directional I/0 lines. A mask option is availablefor software programmable pull-downs on all ofthe I/O pins and four of the pins are capable ofgenerating interrupts.The device is ideally suited for remote-controlkeyboard applications because the pull-downs andthe interrupt drivers on the port pins allowkeyboards to be built without any externalcomponents except the keys themselves. There isno need for external pull-up or pull-down resistors,or diodes for wired-OR interrupts, as these featuresare already designed into the device.
標簽： Infra-red Remote Cont 05K
上傳時間： 2014-01-24
上傳用戶：zl5712176
The 87C576 includes two separate methods of programming theEPROM array, the traditional modified Quick-Pulse method, and anew On-Board Programming technique (OBP).Quick Pulse programming is a method using a number of devicepins in parallel (see Figure 1) and is the traditional way in which87C51 family members have been programmed. The Quick-Pulsemethod supports the following programming functions:– program USER EPROM– verify USER EPROM– program KEY EPROM– program security bits– verify security bits– read signature bytesThe Quick-Pulse method is quite easily suited to standardprogramming equipment as evidenced by the numerous vendors of87C51 compatible programmers on the market today. Onedisadvantage is that this method is not well suited to programming inthe embedded application because of the large number of signallines that must be isolated from the application. In addition, parallelsignals from a programmer would need to be cabled to theapplication’s circuit board, or the application circuit board wouldneed to have logic built-in to perform the programming functions.These requirements have generally made in-circuit programmingusing the modified Quick Pulse method impractical in almost all87C51 family applications.
上傳時間： 2013-10-21
上傳用戶：xiaozhiqban
有兩種方式可以讓設備和應用程序之間聯系：1. 通過為設備創建的一個符號鏈；2. 通過輸出到一個接口WDM驅動程序建議使用輸出到一個接口而不推薦使用創建符號鏈的方法。這個接口保證PDO的安全，也保證安全地創建一個惟一的、獨立于語言的訪問設備的方法。一個應用程序使用Win32APIs來調用設備。在某個Win32 APIs和設備對象的分發函數之間存在一個映射關系。獲得對設備對象訪問的第一步就是打開一個設備對象的句柄。 用符號鏈打開一個設備的句柄為了打開一個設備，應用程序需要使用CreateFile。如果該設備有一個符號鏈出口，應用程序可以用下面這個例子的形式打開句柄：hDevice = CreateFile("\\\\.\\OMNIPORT3", GENERIC_READ | GENERIC_WRITE,FILE_SHARE_READ, NULL, OPEN_EXISTING, FILE_ATTRIBUTE_NORMAL ,NULL);文件路徑名的前綴“\\.\”告訴系統本調用希望打開一個設備。這個設備必須有一個符號鏈，以便應用程序能夠打開它。有關細節查看有關Kdevice和CreateLink的內容。在上述調用中第一個參數中前綴后的部分就是這個符號鏈的名字。注意：CreatFile中的第一個參數不是Windows 98/2000中驅動程序(.sys文件)的路徑。是到設備對象的符號鏈。如果使用DriverWizard產生驅動程序，它通常使用類KunitizedName來構成設備的符號鏈。這意味著符號鏈名有一個附加的數字，通常是0。例如：如果鏈接名稱的主干是L“TestDevice”那么在CreateFile中的串就該是“\\\\.\\TestDevice0”。如果應用程序需要被覆蓋的I/O，第六個參數(Flags)必須或上FILE_FLAG_OVERLAPPED。 使用一個輸出接口打開句柄用這種方式打開一個句柄會稍微麻煩一些。DriverWorks庫提供兩個助手類來使獲得對該接口的訪問容易一些，這兩個類是CDeviceInterface, 和 CdeviceInterfaceClass。CdeviceInterfaceClass類封裝了一個設備信息集，該信息集包含了特殊類中的所有設備接口信息。應用程序能有用CdeviceInterfaceClass類的一個實例來獲得一個或更多的CdeviceInterface類的實例。CdeviceInterface類是一個單一設備接口的抽象。它的成員函數DevicePath()返回一個路徑名的指針，該指針可以在CreateFile中使用來打開設備。下面用一個小例子來顯示這些類最基本的使用方法：extern GUID TestGuid;HANDLE OpenByInterface( GUID* pClassGuid, DWORD instance, PDWORD pError){ CDeviceInterfaceClass DevClass(pClassGuid, pError); if (*pError != ERROR_SUCCESS) return INVALID_HANDLE_VALUE; CDeviceInterface DevInterface(&DevClass, instance, pError); if (*pError != ERROR_SUCCESS) return INVALID_HANDLE_VALUE; cout << "The device path is " << DevInterface.DevicePath() << endl; HANDLE hDev; hDev = CreateFile( DevInterface.DevicePath(), GENERIC_READ | GENERIC_WRITE, FILE_SHARE_READ | FILE_SHARE_WRITE, NULL, OPEN_EXISTING, FILE_ATTRIBUTE_NORMAL, NULL ); if (hDev == INVALID_HANDLE_VALUE) *pError = GetLastError(); return hDev;} 在設備中執行I/O操作一旦應用程序獲得一個有效的設備句柄，它就能使用Win32 APIs來產生到設備對象的IRPs。下面的表顯示了這種對應關系。Win32 API DRIVER_FUNCTION_xxxIRP_MJ_xxx KDevice subclass member function CreateFile CREATE Create ReadFile READ Read WriteFile WRITE Write DeviceIoControl DEVICE_CONTROL DeviceControl CloseHandle CLOSECLEANUP CloseCleanUp 需要解釋一下設備類成員的Close和CleanUp：CreateFile使內核為設備創建一個新的文件對象。這使得多個句柄可以映射同一個文件對象。當這個文件對象的最后一個用戶級句柄被撤銷后，I/O管理器調用CleanUp。當沒有任何用戶級和核心級的對文件對象的訪問的時候，I/O管理器調用Close。如果被打開的設備不支持指定的功能，則調用相應的Win32將引起錯誤（無效功能）。以前為Windows95編寫的VxD的應用程序代碼中可能會在打開設備的時候使用FILE_FLAG_DELETE_ON_CLOSE屬性。在Windows NT/2000中，建議不要使用這個屬性，因?yàn)樗鼘?dǎo)致沒有特權的用戶企圖打開這個設備，這是不可能成功的。I/O管理器將ReadFile和WriteFile的buff參數轉換成IRP域的方法依賴于設備對象的屬性。當設備設置DO_DIRECT_IO標志，I/O管理器將buff鎖住在存儲器中，并且創建了一個存儲在IRP中的MDL域。一個設備可以通過調用Kirp::Mdl來存取MDL。當設備設置DO_BUFFERED_IO標志，設備對象分別通過KIrp::BufferedReadDest或 KIrp::BufferedWriteSource為讀或?qū)懖僮鳙@得buff地址。當設備不設置DO_BUFFERED_IO標志也不設置DO_DIRECT_IO，內核設置IRP 的UserBuffer域來對應ReadFile或WriteFile中的buff參數。然而，存儲區并沒有被鎖住而且地址只對調用進程有效。驅動程序可以使用KIrp::UserBuffer來存取IRP域。對于DeviceIoControl調用，buffer參數的轉換依賴于特殊的I/O控制代碼，它不在設備對象的特性中。宏CTL_CODE（在winioctl.h中定義）用來構造控制代碼。這個宏的其中一個參數指明緩沖方法是METHOD_BUFFERED, METHOD_IN_DIRECT, METHOD_OUT_DIRECT, 或METHOD_NEITHER。下面的表顯示了這些方法和與之對應的能獲得輸入緩沖與輸出緩沖的KIrp中的成員函數：Method Input Buffer Parameter Output Buffer Parameter METHOD_BUFFERED KIrp::IoctlBuffer KIrp::IoctlBuffer METHOD_IN_DIRECT KIrp::IoctlBuffer KIrp::Mdl METHOD_OUT_DIRECT KIrp::IoctlBuffer KIrp::Mdl METHOD_NEITHER KIrp::IoctlType3InputBuffer KIrp::UserBuffer 如果控制代碼指明METHOD_BUFFERED，系統分配一個單一的緩沖來作為輸入與輸出。驅動程序必須在向輸出緩沖放數據之前拷貝輸入數據。驅動程序通過調用KIrp::IoctlBuffer獲得緩沖地址。在完成時，I/O管理器從系統緩沖拷貝數據到提供給Ring 3級調用者使用的緩沖中。驅動程序必須在結束前存儲拷貝到IRP的Information成員中的數據個數。如果控制代碼不指明METHOD_IN_DIRECT或METHOD_OUT_DIRECT，則DeviceIoControl的參數呈現不同的含義。參數InputBuffer被拷貝到一個系統緩沖，這個緩沖驅動程序可以通過調用KIrp::IoctlBuffer。參數OutputBuffer被映射到KMemory對象，驅動程序?qū)@個對象的訪問通過調用KIrp::Mdl來實現。對于METHOD_OUT_DIRECT，調用者必須有對緩沖的寫訪問權限。注意，對METHOD_NEITHER，內核只提供虛擬地址；它不會做映射來配置緩沖。虛擬地址只對調用進程有效。這里是一個用METHOD_BUFFERED的例子：首先，使用宏CTL_CODE來定義一個IOCTL代碼：#define IOCTL_MYDEV_GET_FIRMWARE_REV \CTL_CODE (FILE_DEVICE_UNKNOWN,0,METHOD_BUFFERED,FILE_ANY_ACCESS)現在使用一個DeviceIoControl調用：BOOLEAN b;CHAR FirmwareRev[60];ULONG FirmwareRevSize;b = DeviceIoControl(hDevice, IOCTL_MYDEV_GET_VERSION_STRING, NULL, // no input 注意，這里放的是包含有執行操作命令的字符串指針 0, FirmwareRev, //這里是output串指針，存放從驅動程序中返回的字符串。sizeof(FirmwareRev),& FirmwareRevSize, NULL // not overlapped I/O );如果輸出緩沖足夠大，設備拷貝串到里面并將拷貝的資結束設置到FirmwareRevSize中。在驅動程序中，代碼看起來如下所示：const char* FIRMWARE_REV = "FW 16.33 v5";NTSTATUS MyDevice::DeviceControl( KIrp I ){ ULONG fwLength=0; switch ( I.IoctlCode() ) { case IOCTL_MYDEV_GET_FIRMWARE_REV: fwLength = strlen(FIRMWARE_REV)+1; if (I.IoctlOutputBufferSize() >= fwLength) { strcpy((PCHAR)I.IoctlBuffer(),FIRMWARE_REV); I.Information() = fwLength; return I.Complete(STATUS_SUCCESS); } else { } case . . . } }
標簽： 驅動程序 應用程序 接口
上傳時間： 2013-10-17
上傳用戶：gai928943
The STWD100 watchdog timer circuits are self-contained devices which prevent systemfailures that are caused by certain types of hardware errors (non-responding peripherals,bus contention, etc.) or software errors (bad code jump, code stuck in loop, etc.).The STWD100 watchdog timer has an input, WDI, and an output, WDO (see Figure 2). Theinput is used to clear the internal watchdog timer periodically within the specified timeoutperiod, twd (see Section 3: Watchdog timing). While the system is operating correctly, itperiodically toggles the watchdog input, WDI. If the system fails, the watchdog timer is notreset, a system alert is generated and the watchdog output, WDO, is asserted (seeSection 3: Watchdog timing).The STWD100 circuit also has an enable pin, EN (see Figure 2), which can enable ordisable the watchdog functionality. The EN pin is connected to the internal pull-downresistor. The device is enabled if the EN pin is left floating.
上傳時間： 2013-10-22
上傳用戶：taiyang250072
winCE msdn講座 XP Embedded Now and the future Windows XP Embedded Developmentand Deployment Model OverviewWindows XP Embedded Component ModelWindows XP Embedded Studio Tools Microsoft WindowsXP Embedded Product Highlights Componentized version of Windows XP Professional~ 12,000 components and updates as of Service Pack 2Flexible localizationSame binaries and API as Windows XP ProfessionalHotfixes and service packsEmbedded Enabling FeaturesRuns on standard PC hardwareSupports boot on hard drives, compact flash, DiskOnChipand read-only mediaSupport for remote install and remote bootHeadless device and remote management supportIntegration with Microsoft management tools
上傳時間： 2013-10-31
上傳用戶：jrsoft
The PL2303 USB to Serial adapter is your smart and convenient accessory forconnecting RS-232 serial devices to your USB-equipped Windows host computer. Itprovides a bridge connection with a standard DB 9-pin male serial port connector inone end and a standard Type-A USB plug connector on the other end. You simplyattach the serial device onto the serial port of the cable and plug the USB connectorinto your PC USB port. It allows a simple and easy way of adding serial connectionsto your PC without having to go thru inserting a serial card and traditional portconfiguration.This USB to Serial adapter is ideal for connecting modems, cellular phones, PDAs,digital cameras, card readers and other serial devices to your computer. It providesserial connections up to 1Mbps of data transfer rate. And since USB does not requireany IRQ resource, more devices can be attached to the system without the previoushassles of device and resource conflicts.Finally, the PL-2303 USB to Serial adapter is a fully USB Specification compliantdevice and therefore supports advanced power management such as suspend andresume operations as well as remote wakeup. The PL-2303 USB Serial cable adapteris designed to work on all Windows operating systems.
標簽： Adapter Serial 2303 USB
上傳時間： 2013-11-01
上傳用戶：ghostparker
用單片機配置FPGA—PLD設計技巧 Configuration/Program Method for Altera Device Configure the FLEX Device You can use any Micro-Controller to configure the FLEX device–the main idea is clocking in ONE BITof configuration data per CLOCK–start from the BIT 0The total Configuration time–e.g. 10K10 need 15K byte configuration file•calculation equation–10K10* 1.5= 15Kbyte–configuration time for the file itself•15*1024*8*clock = 122,880Clock•assume the CLOCK is 4MHz•122,880*1/4Mhz=30.72msec
標簽： FPGA PLD 用單片機 設計技巧
上傳時間： 2013-10-09
上傳用戶：a67818601
蟲蟲下載站版權所有 京ICP備2021023401號-1
