<sub id="xfmul"></sub>
A series of .c and .m files which allow one to perform univariate and bivariate wavelet analysis of discrete time series. Noother wavelet package is necessary -- everything is contained in this archive. The C-code computes the DWT and maximal overlap DWT. MATLAB routines are then used to compute such quantities as the wavelet variance, covariance, correlation, cross-covariance and cross-correlation. Approximate confidence intervals are available for all quantities except the cross-covariance and cross-correlation. A set of commands is provided. For a description of this example, please see http://www.eurandom.tue.nl/whitcher/software/.
標簽： univariate and bivariate analysis
上傳時間： 2015-06-23
上傳用戶：chongcongying
Linux 虛擬網絡接口 實例 In the Linux (or Unix) world, most network interfaces, such as eth0 and ppp0, are associated with a physical device that is in charge of transmitting and receiving data packets. However, some logical network interfaces don t feature any physical packet transmission. The most well-known examples of these "virtual" interfaces are the shaper and eql interfaces.
標簽： Linux interfaces network world
上傳時間： 2014-01-11
上傳用戶：zhangzhenyu
Windows下讀寫硬件的工具. RW - Read & Write utility, for hardware engineers, firmware (BIOS) engineers, driver developers, QA engineers, performance test engineers, diagnostic engineers, etc., This utility access almost all the computer hardware, including PCI (PCI Express), PCI Index/Data, Memory, Memory Index/Data, I/O Space, I/O Index/Data, Super I/O, Clock Generator, DIMM SPD, SMBus Device, CPU MSR Registers, ATA/ATAPI Identify Data, ACPI Tables Dump (include AML decode), Embedded Controller, USB Information and LPT Remote Access. And also an Command Window is provided to access hardware manually.
標簽： engineers firmware hardware Windows
上傳時間： 2015-07-01
上傳用戶：xc216
RW - Read & Write utility, for hardware engineers, firmware (BIOS) engineers, driver developers, QA engineers, performance test engineers, diagnostic engineers, etc., This utility access almost all the computer hardware, including PCI (PCI Express), PCI Index/Data, Memory, Memory Index/Data, I/O Space, I/O Index/Data, Super I/O, Clock Generator, DIMM SPD, SMBus Device, CPU MSR Registers, ATA/ATAPI Identify Data, ACPI Tables Dump (include AML decode), Embedded Controller, USB Information and LPT Remote Access. And also an Command Window is provided to access hardware manually. Website1: http://rw.net-forces.com/ Website2: http://home.kimo.com.tw/ckimchan.tw/ Website3: http://jacky5488.myweb.hinet.net/ For best view, please change the screen resolution to 1024 x 768 (or above) pixels.
標簽： engineers developers firmware hardware
上傳時間： 2013-12-22
上傳用戶：王楚楚
這個是關于GCC編譯器編譯安裝文檔，在您需要定制安裝GCC或搭建交叉編譯器（Cross-GCC）時可以參考一下哦
上傳時間： 2014-01-15
上傳用戶：小儒尼尼奧
his project was built and tested with WinAVR-20060125. Make sure the MCU target define in the Makefiles corresponds to the AVR you are using!! To build the code, just install WinAVR and run "make" from the console in echomaster and echoslave subdirs. "make program" will program the device if you have a AVRISP attached. Remember to set the AVR device to at least 8MHz. The AVR may use the programmable clock from MC1319x, just remember to check if the MC1319x and SPI communication is working FIRST! Otherwise you wont get any clock signal to the AVR and then you can t program it or reset the fuses! The MC1319x has default clock output of 32kHz so you will have to set your programmer to a very low frequency (<=32kHz/4) to be able to program it while it is running on that!
標簽： the 20060125 project WinAVR
上傳時間： 2014-10-10
上傳用戶：yan2267246
藍牙協議This specification describes the Audio/Video Control Transport Protocol (AVCTP), which is used to transport command and response messages for controlling Audio Video features in conformant devices. This protocol enables a device to support more than one control profile at the same time each supported profile shall define its own message formatting and/or usage rules.
標簽： specification describes Transport Protocol
上傳時間： 2015-08-11
上傳用戶：大融融rr
matlab編寫的一個涂膠機的仿真程序，可用于仿真和控制方法的驗證，具體可參見文獻"Identification and cross-directional control of coating processes"
上傳時間： 2015-08-16
上傳用戶：sammi
Linux 2.4內核字符設備驅動開發實例。 是Linux下驅動開發人員再好不過的參考源碼。編譯之后加載驅動，附有測試程序進行驅動的測試！ Linux kernel 2.4 char device driver example.
上傳時間： 2015-08-22
上傳用戶：liglechongchong
遺傳算法的matlab程序，包括三個，cross,ga,myfun
上傳時間： 2014-01-18
上傳用戶：王者A
