All inputs of the C16x family have Schmitt-Trigger input characteristics. These Schmitt-Triggers are intended to always provide proper internal low and high levels, even if anundefined voltage level (between TTL-VIL and TTL-VIH) is externally applied to the pin.The hysteresis of these inputs, however, is very small, and can not be properly used in anapplication to suppress signal noise, and to shape slow rising/falling input transitions.Thus, it must be taken care that rising/falling input signals pass the undefined area of theTTL-specification between VIL and VIH with a sufficient rise/fall time, as generally usualand specified for TTL components (e.g. 74LS series: gates 1V/us, clock inputs 20V/us).The effect of the implemented Schmitt-Trigger is that even if the input signal remains inthe undefined area, well defined low/high levels are generated internally. Note that allinput signals are evaluated at specific sample points (depending on the input and theperipheral function connected to it), at that signal transitions are detected if twoconsecutive samples show different levels. Thus, only the current level of an input signalat these sample points is relevant, that means, the necessary rise/fall times of the inputsignal is only dependant on the sample rate, that is the distance in time between twoconsecutive evaluation time points. If an input signal, for instance, is sampled throughsoftware every 10us, it is irrelevant, which input level would be seen between thesamples. Thus, it would be allowable for the signal to take 10us to pass through theundefined area. Due to the sample rate of 10us, it is assured that only one sample canoccur while the signal is within the undefined area, and no incorrect transition will bedetected. For inputs which are connected to a peripheral function, e.g. capture inputs, thesample rate is determined by the clock cycle of the peripheral unit. In the case of theCAPCOM unit this means a sample rate of 400ns @ 20MHz CPU clock. This requiresinput signals to pass through the undefined area within these 400ns in order to avoidmultiple capture events.For input signals, which do not provide the required rise/fall times, external circuitry mustbe used to shape the signal transitions.In the attached diagram, the effect of the sample rate is shown. The numbers 1 to 5 in thediagram represent possible sample points. Waveform a) shows the result if the inputsignal transition time through the undefined TTL-level area is less than the time distancebetween the sample points (sampling at 1, 2, 3, and 4). Waveform b) can be the result ifthe sampling is performed more than once within the undefined area (sampling at 1, 2, 5,3, and 4).Sample points:1. Evaluation of the signal clearly results in a low level2. Either a low or a high level can be sampled here. If low is sampled, no transition willbe detected. If the sample results in a high level, a transition is detected, and anappropriate action (e.g. capture) might take place.3. Evaluation here clearly results in a high level. If the previous sample 2) had alreadydetected a high, there is no change. If the previous sample 2) showed a low, atransition from low to high is detected now.
上傳時間： 2013-10-23
上傳用戶：copu
All inputs of the C16x family have Schmitt-Trigger input characteristics. These Schmitt-Triggers are intended to always provide proper internal low and high levels, even if anundefined voltage level (between TTL-VIL and TTL-VIH) is externally applied to the pin.The hysteresis of these inputs, however, is very small, and can not be properly used in anapplication to suppress signal noise, and to shape slow rising/falling input transitions.Thus, it must be taken care that rising/falling input signals pass the undefined area of theTTL-specification between VIL and VIH with a sufficient rise/fall time, as generally usualand specified for TTL components (e.g. 74LS series: gates 1V/us, clock inputs 20V/us).The effect of the implemented Schmitt-Trigger is that even if the input signal remains inthe undefined area, well defined low/high levels are generated internally. Note that allinput signals are evaluated at specific sample points (depending on the input and theperipheral function connected to it), at that signal transitions are detected if twoconsecutive samples show different levels. Thus, only the current level of an input signalat these sample points is relevant, that means, the necessary rise/fall times of the inputsignal is only dependant on the sample rate, that is the distance in time between twoconsecutive evaluation time points. If an input signal, for instance, is sampled throughsoftware every 10us, it is irrelevant, which input level would be seen between thesamples. Thus, it would be allowable for the signal to take 10us to pass through theundefined area. Due to the sample rate of 10us, it is assured that only one sample canoccur while the signal is within the undefined area, and no incorrect transition will bedetected. For inputs which are connected to a peripheral function, e.g. capture inputs, thesample rate is determined by the clock cycle of the peripheral unit. In the case of theCAPCOM unit this means a sample rate of 400ns @ 20MHz CPU clock. This requiresinput signals to pass through the undefined area within these 400ns in order to avoidmultiple capture events.
上傳時間： 2014-04-02
上傳用戶：han_zh
This application note demonstrates how to write an Inter Integrated Circuit bus driver (I2C) for the XA-S3 16-bitMicrocontroller from Philips Semiconductors.Not only the driver software is given. This note also contains a set of (example) interface routines and a smalldemo application program. All together it offers the user a quick start in writing a complete I2C system applicationwith the PXAS3x.The driver routines support interrupt driven single master transfers. Furthermore, the routines are suitable foruse in conjunction with real time operating systems.
上傳時間： 2013-11-02
上傳用戶：zw380105939
I2C interface, is a very powerful tool for system designers. Theintegrated protocols allow systems to be completely software defined.Software development time of different products can be reduced byassembling a library of reusable software modules. In addition, themultimaster capability allows rapid testing and alignment ofend-products via external connections to an assembly-line computer.The mask programmable 87LPC76X and its EPROM version, the87LPC76X, can operate as a master or a slave device on the I2Csmall area network. In addition to the efficient interface to thededicated function ICs in the I2C family, the on-board interfacefacilities I/O and RAM expansion, access to EEPROM andprocessor-to-processor communications.
標簽： microcontro Using 76X LPC
上傳時間： 2013-12-30
上傳用戶：Artemis
//芯片資料請到www.elecfans.com查找 //DS1820 C51 子程序//這里以11.0592M晶體為例，不同的晶體速度可能需要調整延時的時間//sbit DQ =P2^1;//根據實際情況定義端口 typedef unsigned char byte;typedef unsigned int word; //延時void delay(word useconds){ for(;useconds>0;useconds--);} //復位byte ow_reset(void){ byte presence; DQ = 0; //pull DQ line low delay(29); // leave it low for 480us DQ = 1; // allow line to return high delay(3); // wait for presence presence = DQ; // get presence signal delay(25); // wait for end of timeslot return(presence); // presence signal returned} // 0=presence, 1 = no part //從 1-wire 總線上讀取一個字節byte read_byte(void){ byte i; byte value = 0; for (i=8;i>0;i--) { value>>=1; DQ = 0; // pull DQ low to start timeslot DQ = 1; // then return high delay(1); //for (i=0; i<3; i++); if(DQ)value|=0x80; delay(6); // wait for rest of timeslot } return(value);} //向 1-WIRE 總線上寫一個字節void write_byte(char val){ byte i; for (i=8; i>0; i--) // writes byte, one bit at a time { DQ = 0; // pull DQ low to start timeslot DQ = val&0x01; delay(5); // hold value for remainder of timeslot DQ = 1; val=val/2; } delay(5);} //讀取溫度char Read_Temperature(void){ union{ byte c[2]; int x; }temp; ow_reset(); write_byte(0xCC); // Skip ROM write_byte(0xBE); // Read Scratch Pad temp.c[1]=read_byte(); temp.c[0]=read_byte(); ow_reset(); write_byte(0xCC); //Skip ROM write_byte(0x44); // Start Conversion return temp.x/2;}
上傳時間： 2013-11-03
上傳用戶：hongmo
#include <reg51.h>#include<intrins.h> #define BUSY1 (DQ1==0) sbit DQ1 = P0^4; unsigned char idata TMP; unsigned char idata TMP_d; unsigned char f; void wr_ds18_1(char dat);unsigned char rd_ds18_1(); /***************延時程序，單位us,大于10us*************/void time_delay(unsigned char time){ time=time-10; time=time/6; while(time!=0)time--;} /*****************************************************//* reset ds18b20 *//*****************************************************/void ds_reset_1(void){ unsigned char idata count=0; DQ1=0; time_delay(240); time_delay(240); DQ1=1; return;}
上傳時間： 2013-10-29
上傳用戶：sssnaxie
PLC TM卡開發系統匯編程序(ATM8051) ;***************** 定義管腳*************************SCL BIT P1.0SDA BIT P1.1GC BIT P1.2BZ BIT P3.6LEDI BIT P1.4LEDII BIT P1.5OK BIT 20H.1OUT1 BIT P1.3OUT2 BIT P1.0OUT3 BIT P1.1RXD BIT P3.0TXD BIT P3.1PCV BIT P3.2WPC BIT P3.3RPC BIT P3.5LEDR BIT P3.4LEDL BIT P3.6TM BIT P3.7;********************定義寄存器***********************ROMDTA EQU 30H;NUMBY EQU 61H;SLA EQU 60H;MTD EQU 2FH;MRD EQU 40H;TEMP EQU 50H;;ORG 00H;;INDEX:MOV P1, #00H;MOV P2, #0FFHMOV MTD ,#00HCALL REEMOV R0,40HCJNE R0,#01,NO;MOV P2,#1CHLJMP VIMEN MOV P2,#79HACALL TOUCHRESET ;JNC NO ;CALL READTM ;CJNE A,#01H,NO;NOPMOV MTD, #00HCALL WEENOPMOV P2,#4AHSETB BZCALL TIMECLR BZMOV PCON, #0FFHVIME:CALL TIME1CALL TOUCHRESETJNC VIMECALL READTMCJNE A, #01H,VIME;NOPNOPNOPIII: MOV MTD,#00HCALL REECALL BBJNB OK,NO1LJMP ZHUNO1:MOV MTD,#10H
上傳時間： 2014-03-24
上傳用戶：448949
用單片機配置FPGA—PLD設計技巧 Configuration/Program Method for Altera Device Configure the FLEX Device You can use any Micro-Controller to configure the FLEX device–the main idea is clocking in ONE BITof configuration data per CLOCK–start from the BIT 0The total Configuration time–e.g. 10K10 need 15K byte configuration file•calculation equation–10K10* 1.5= 15Kbyte–configuration time for the file itself•15*1024*8*clock = 122,880Clock•assume the CLOCK is 4MHz•122,880*1/4Mhz=30.72msec
上傳時間： 2013-10-09
上傳用戶：a67818601
自動檢測80C51 串行通訊中的波特率本文介紹一種在80C51 串行通訊應用中自動檢測波特率的方法。按照經驗，程序起動后所接收到的第1 個字符用于測量波特率。這種方法可以不用設定難于記憶的開關，還可以免去在有關應用中使用多種不同波特率的煩惱。人們可以設想：一種可靠地實現自動波特檢測的方法是可能的，它無須嚴格限制可被確認的字符。問題是：在各種的條件下，如何可以在大量允許出現的字符中找出波特率的定時間隔。顯然，最快捷的方法是檢測一個單獨位時間（single bit time），以確定接收波特率應該是多少。可是，在RS-232 模式下，許多ASCII 字符并不能測量出一個單獨位時間。對于大多數字符來說，只要波特率存在合理波動（這里的波特率是指標準波特率），從起始位到最后一位“可見”位的數據傳輸周期就會在一定范圍內發生變化。此外，許多系統采用8 位數據、無奇偶校驗的格式傳輸ASCII 字符。在這種格式里，普通ASCII 字節不會有MSB 設定
上傳時間： 2013-10-15
上傳用戶：shirleyYim
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their productsor to discontinue any product or service without notice, and advise customers to obtain the latestversion of relevant information to verify, before placing orders, that information being relied onis current and complete. All products are sold subject to the terms and conditions of sale suppliedat the time of order acknowledgement, including those pertaining to warranty, patentinfringement, and limitation of liability
上傳時間： 2013-12-26
上傳用戶：凌云御清風
